Model 2210 Overview ............................................................... 2 Tools Needed ........................................................ 2 Hardware................................................................2 Assembly........................................................... 3-10 Installation............................................................ 11 Document 101293 RevA 1 Drawer Removal ................................................. 11 Maintenance ........................
OVERVIEW COMPONENT IDENTIFICATION NOTE: Save all packaging in case re-shipment is required. Perform the following sequence in order when setting up the table: Unpacking Assembly Leveling the Table Installing the Paper Roll NOTE: Inspect all boxes and contents for damage. Report any damage to the carrier immediately. MODEL 2210 For the above model you will receive three separate cartons: a frame & shelf carton, an upholstery carton, and a drawer carton.
MODEL 2210 STEP 1 Notch Screw C Screw C STEP A: Start with table frame inverted: note the position of the Notch in the drawing above is facing upwards. STEP B: Positon Legs in corners (see drawing above). Insert Screws C (1/4”-20 x 1 1/4”) and snug up by hand only at this time.
MODEL 2210 STEP 2 Screw B Drawer Supports with holes upward and toward Foot End Foot E nd Screw B Tab Screw B Drawer Supports with holes upward and toward Foot End Screw B Screw B Shelf Support STEP A: With table in the upright position install Shelf Support using 4 Screws B (1/4”-20 x 2”). Do not tighten at this time.
MODEL 2210 STEP 3 Top Rail Tab Paper Shelf Head End Drawer Support Remove this Screw Only STEP A: Remove one Drawer Support screw from the Head End of the table as shown. STEP B: Insert Paper Shelf between the Top Rail and the loose Drawer Support. Make sure the Paper Shelf is mounted below the Tab as shown. STEP C: Reinstall the Drawer Support and its corresponding screw. Do not tighten at this time.
MODEL 2210 STEP 4 Screw G Tab Paper Shelf Nut H Snap Rivets STEP A: Install Screw G (1/4”-20 x 1/2”) through Tab and Paper Shelf as shown. Tighten Nut H (1/4”-20) onto Screw G. Install 3 Snap Rivets into holes on Paper Shelf and the top of the frame rail.
MODEL 2210 STEP 5 5 Detail of Drawer Slide Bumpers LH Side RH Side Drawer Support Screw E Nut K Shelf Support Drawer Slide STEP A: The drawers can be installed so they open from the right hand side (RH Side) or the left hand side (LH Side) of the table. The view above and the instructions below are for right hand installation. STEP B: Position the (4) Drawer Slides on top of the Drawer Support rails. The rubber bumpers should be on the LH Side of the table, facing upward.
MODEL 2210 STEP 6 STEP A: Install J-Bolts as shown in Figure A. Thread Nut L (3/8”) completely onto J-Bolt. Place Washer M onto J-Bolt and thread into Backrest as shown in Figure A. Position J-Bolt toward head of table as shown and tighten nut against backrest. Install J-Bolts onto upholstery top J-Bolt R Rounded Corner Figure A Foot End Dowel Rod Screw F Screw A Screw A STEP B: Set upholstery top and bottom on frame, with Rounded Corners of the upholstery bottom placed at the Foot End of the table.
MODEL 2210 STEP 7 Snap Rivet Shelf Side Plate Snap Rivet Lower Shelf Support Screw B Snap Rivet STEP A: Loosen Screws B at the foot of the table where indicated just enough to allow installation of the Side Plate. STEP B: Mount Side Plate so that the slots of the plate straddle the Screws B that were just loosened. STEP C: Press the top of the Side Plate up against the frame and align the top hole of the plate with the hole in the frame. Insert Snap Rivet into the aligned holes.
MODEL 2210 STEP 8 CAUTION DO NOT USE SHELF AS A STEP! CAUTION MAXIMUM LOAD 15 LBS. PER DRAWER Drawer Slide Positioning Incorrect Positioning Correct Positioning To install drawers, pull drawer slides forward and align the slots of the drawer-mounted slides to their mate on the frame. Push the drawers inward until they reach their fully-closed position.
INSTALLATION Leveling the Table A Leveling Screw Pad is located at each corner under the table’s base. Adjust the four Leveling Screw Pads, by turning them up or down, to achieve a solid, level installation. Leveling Screw Pad DRAWER REMOVAL Retaining Clips Drawer (Bottom View) To remove Drawer from bottom slide support: Fully extend the Drawer, locate the Retaining Clips and push both clips in a clockwise direction as you pull the Drawer forward and out.
MAINTENANCE Preventative Maintenance • Inspect the mechanical functions to ensure satisfactory operation. • Check fasteners to make sure they are present and secured tightly. Cleaning Upholstery Regular care should be maintained by daily wiping with a damp cloth or sponge and periodic cleaning with a mild soap and water solution. Let air dry before placing anything on top of upholstery.