Install Instructions

ManualsBrandsBraeburn ManualsHeating Supplies7 Day, 5-2 Day Programmable Touchscreen Hybrid Thermostat w/ Humidification Control (4H/2C)

Programmable Touchscreen Thermostat

Speciﬁcations

Installation and Wiring

Quick Reference

Installer Settings

System Testing

To prevent damage to the thermostat, never use a sharp instrument

to press the touchscreen keys. Always press keys with your ﬁngers.

Attention

• Possible electric shock or damage to equipment can occur.

• Disconnect power before beginning installation.

Caution

This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline batteries for proper

operation.

When connecting 24 Volt AC Power the batteries may be installed as a backup. Thermostat

installation and all components of the system shall conform to Class II Circuits per NEC code.

For use only as described in this manual. Any other use will void warranty.

6425

Up to 4 Heat / 2 Cool Heat Pump

Up to 3 Heat / 2 Cool Conventional

with Humidity Control

Warning

For installation by experienced service technicians only.

6425-100-01

Installer Guide

Touchscreen

This thermostat is compatible with:

• Single stage heat / cool conventional and heat pump systems

• Conventional systems up to 3 stages of heating and 2 stages of cooling

• Heat pump systems up to 4 stages of heating and 2 stages of cooling

• 250 – 750 millivolt heating only systems

Electrical and control speciﬁcations:

• Electrical Rating: 24 Volt AC

• 1 amp maximum load per terminal

• AC Power: 18 – 30 Volts AC

• DC Power: 3.0 Volt DC (2 “AA” Alkaline

Batteries Included)

• Control Range: 45° – 90° F (7° – 32° C)

• Temperature Accuracy: +/- 1° F (+/- .5° C)

• Outdoor Temperature Display Range:

-40° - 120° F (-40° - 49° C)

Humidiﬁcation Speciﬁcations

• Humidiﬁcation Control Range: 10% - 50% RH

• Dehumidiﬁcation Control Range: 40% - 80% RH

Speciﬁcations

Terminations

Rc, Rh, G, W1/E/AUX1, W2/AUX2, W3/O/B, Y1, Y2, C,

L, H, A/D, S1, S2

Summary of content (16 pages)

PAGE 1
® Installer Guide Touchscreen ® Programmable Touchscreen Thermostat 6425 Up to 4 Heat / 2 Cool Heat Pump Up to 3 Heat / 2 Cool Conventional with Humidity Control 1 Specifications 2 Installation and Wiring 3 Quick Reference 4 Installer Settings 5 System Testing Attention To prevent damage to the thermostat, never use a sharp instrument to press the touchscreen keys. Always press keys with your fingers. Warning For installation by experienced service technicians only.
PAGE 2
Installation and Wiring Warning Disconnect power before beginning installation. Thermostat Location Install the thermostat approximately 5 feet (1.5m) above the floor in an area that has a good amount of air circulation and maintains an average room temperature. Avoid installation in locations where the thermostat can be affected by drafts, dead air spots, hot or cold air ducts, sunlight, appliances, concealed pipes, chimneys and outside walls.
PAGE 3
2 Provide Power C + + Batteries Installed as Shown 24VAC Power Terminal (C) • For 24 Volt AC power, you must connect the common side of the transformer to the C terminal on the thermostat sub-base. In dual transformer installations, the transformer common must come from the cooling transformer. • For battery power, insert the 2 supplied “AA” type alkaline batteries into the battery compartment located in the rear housing of the thermostat.
PAGE 4
3 Connecting Your Wires (continued) Wiring Terminations Terminal Function Description H Output Humidifier A / D Output (A) Economizer Control, (D) Dehumidifier G Output Fan Control Rc Input 24 Volt AC Cooling Transformer (Dual Transformer Systems Only) Rh Input W1 / E / Output AUX1 Power Connection (24 Volt AC Heating Transformer or Millivolt Power Source) (W1) 1st Stage Conventional Heat, (E) Emergency Heat, (AUX1) 1st Stage Auxiliary Heat W2 / AUX2 Out
PAGE 5
Conventional Systems Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section.
PAGE 6
Heat Pump Systems Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section.
PAGE 7
All System Types Additional Wiring Options NOTE: Additional options are configured in the Installer Settings section. S1 S2 Indoor or Outdoor Remote Sensor [note 1] A/D Economizer Control / Dehumidification Output [note 2] H Humidification Output [note 3] NOTES - Additional Wiring Options [1] These terminals can be used to connect a Braeburn® indoor or outdoor remote sensor.
PAGE 8
3 Quick Reference 13 12 Instructions 11 1 10 2 9 8 3 14 4 RESET 5 6 15 7 Thermostat Display 1 Room Temperature....................... .Displays the current room temperature 2 Lock Mode Indicator .................... .Indicates if the thermostat is locked 3 Set Temperature........................... .Displays the current set point temperature 4 Humidity Indicator........................ .Indicates when there is a call for humidity 5 Fan Indicator............................
PAGE 9
RESET Thermostat TouchPads NOTE: Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are the “touch sensitive” segments used to adjust your thermostat. Depending on the equipment installed, all touch pads may not show.
PAGE 10
4 Installer Settings The Installer Settings must be properly configured in order for this thermostat to operate correctly. The Installer Settings are menu driven. The portion of these settings that do not apply to your setup will be skipped. These settings are indicated below with comments. More detail on each setting follows this table. 1. 2. 3. 4. Touch and hold down the SYSTEM and CONFIG TouchPads for 3 seconds. Release both buttons and the first installer setting will be displayed.
PAGE 11
No.
PAGE 12
No.
PAGE 13
Reversing Valve [Note 5] – Selects the output state of the O/B terminal. Select O for this terminal to be active in the cool mode or select B for this terminal to be active in the heat mode. 14 Auxiliary Fossil Fuel Heat Pump Control [note 4] – When set to electric (AE AUX), both the compressor (1st stage) and auxiliary stage(s) will run when a call for auxiliary heat is made. When set to gas (AG AUX), the compressor stage(s) will be locked out one minute after a call for auxiliary heat.
PAGE 14
27 Dehumidification Fan Speed Control [note 10] – Select normally inactive relay (NI) or a normally active (NA) relay. 28 Auto Changeover Dead Band [note 11] – When Auto Changeover mode is enabled in option 5 and selected, the system automatically switches between heating and cooling when the room temperature meets the normal criteria for either a heating or cooling call. There is a forced separation (dead band) between the heating and cooling set points so the systems do not work against each other.
PAGE 15
5 System Testing Warning Read Before Testing • Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system control board to test the thermostat installation. This could damage the thermostat and void the warranty. • Do not select the COOL mode of operation if the outside temperature is below 50º F (10º C). This could possibly damage the controlled cooling system and may cause personal injury.
PAGE 16
® Limited Warranty When installed by a professional contractor, this product is backed by a 5 year limited warranty. Limitations apply. For limitations, terms and conditions, you may obtain a full copy of this warranty: · Visit us online: www.braeburnonline.com/warranty · Phone us: 866.268.5599 · Write us: Braeburn Systems LLC 2215 Cornell Avenue Montgomery, IL 60538 5 YEAR LIMITED WARRANTY Store this manual for future reference.