6100 Installation Manual

ManualsBrandsBraeburn ManualsThermostatsDeluxe Series - 7 Day Programmable Thermostat - Touchscreen - 1H/1C

Programmable Touchscreen Thermostats

Speciﬁcations

Installation and Wiring

Quick Reference

Installer Settings

System Testing

To prevent damage to the thermostat, never use a sharp instrument

to press the touchscreen keys. Always press keys with your ﬁngers.

Attention

• Possible electric shock or damage to equipment can occur.

• Disconnect power before beginning installation.

Caution

This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline batteries for proper

operation. When connecting 24 Volt AC Power the batteries may be installed as a backup. Thermostat

installation and all components of the system shall conform to Class II Circuits per NEC code.

For use only as described in this manual. Any other use will void warranty.

6100

Single Stage Heat / Cool Conventional

or Heat Pump

6300

Up to 4 Heat / 2 Cool Heat Pump

Up to 3 Heat / 2 Cool Conventional

Warning

For installation by experienced service technicians only.

6100-100-01

Installer Guide

Touchscreen

This thermostat is compatible with:

• Single stage heat / cool conventional and heat pump systems

• Conventional systems up to 3 stages of heating and 2 stages of cooling (6300 only)

• Heat pump systems up to 4 stages of heating and 2 stages of cooling (6300 only)

• 250 – 750 millivolt heating only systems

Electrical and control speciﬁcations:

• Electrical Rating: 24 Volt AC

• 1 amp maximum load per terminal

• AC Power: 18 – 30 Volts AC

• DC Power: 3.0 Volt DC (2 “AA” Alkaline

Batteries Included)

• Control Range: 45° – 90° F (7° – 32° C)

• Temperature Accuracy: +/- 1° F (+/- .5° C)

• Outdoor Temperature Display Range:

-40° - 120° F (-40° - 49° C)

Speciﬁcations

Terminations

• 6100: G, Rc, Rh, W, O/B, Y, C, S1, S2

• 6300: A, G, Rc, Rh, W1/E/AUX1, W2/AUX2, W3/O/B,

Y1, Y2, C, L, S1, S2

Summary of content (18 pages)

PAGE 1
® Installer Guide Touchscreen ® Programmable Touchscreen Thermostats 6100 Single Stage Heat / Cool Conventional or Heat Pump 6300 Up to 4 Heat / 2 Cool Heat Pump Up to 3 Heat / 2 Cool Conventional 1 Specifications 2 Installation and Wiring 3 Quick Reference 4 Installer Settings 5 System Testing Attention To prevent damage to the thermostat, never use a sharp instrument to press the touchscreen keys. Always press keys with your fingers. Warning For installation by experienced service technicians only.
PAGE 2
Installation and Wiring Warning Disconnect power before beginning installation. Thermostat Location Install the thermostat approximately 5 feet (1.5m) above the floor in an area that has a good amount of air circulation and maintains an average room temperature. Avoid installation in locations where the thermostat can be affected by drafts, dead air spots, hot or cold air ducts, sunlight, appliances, concealed pipes, chimneys and outside walls.
PAGE 3
2 Provide Power C + + Batteries Installed as Shown 24VAC Power Terminal (C) • For 24 Volt AC power, you must connect the common side of the transformer to the C terminal on the thermostat sub-base. In dual transformer installations, the transformer common must come from the cooling transformer. • For battery power, insert the 2 supplied “AA” type alkaline batteries into the battery compartment located in the rear housing of the thermostat.
PAGE 4
3 Connecting Your Wires (continued) Wiring Terminations for model 6300 Terminal Function Description A Output Economizer Control G Output Fan Control Rc Input 24 Volt AC Cooling Transformer (Dual Transformer Systems Only) Rh Input Power Connection (24 Volt AC Heating Transformer or Millivolt Power Source) W1 / E / Output AUX1 (W1) 1st Stage Conventional Heat, (E) Emergency Heat, (AUX1) 1st Stage Auxiliary Heat W2 / AUX2 Output (W2) 2nd Stage Conve
PAGE 5
Conventional Systems Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section. The 6100 is a single stage thermostat and not intended for multi stage equipment.
PAGE 6
Heat Pump Systems Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section. The 6100 is a single stage thermostat and not intended for multi stage equipment.
PAGE 7
All System Types Additional Wiring Options NOTE: Additional options are configured in the Installer Settings section. S1 Indoor or Outdoor Remote Sensor [note 1] S2 Indoor or Outdoor Remote Sensor [note 1] A Economizer Control (6300 only) [note 2] NOTES - Additional Wiring Options [1] These terminals can be used to connect a Braeburn® indoor or outdoor remote sensor. [2] This terminal can be used for outside air control (model 6300 only).
PAGE 8
3 Quick Reference 12 11 Instructions 10 1 9 2 8 7 3 13 RESET 4 5 14 6 Thermostat Display 1 Room Temperature....................... .Displays the current room temperature 2 Lock Mode Indicator .................... .Indicates if the thermostat is locked 3 Set Temperature........................... .Displays the current set point temperature 4 Fan Indicator................................. .Indicates when the system fan is running 5 Service Indicators .......................
PAGE 9
RESET Thermostat TouchPads NOTE: Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are the “touch sensitive” segments used to adjust your thermostat. Depending on the equipment installed, all touch pads may not show.
PAGE 10
4 Installer Settings The Installer Settings must be properly configured in order for this thermostat to operate correctly. The Installer Settings are menu driven. The portion of these settings that do not apply to your setup will be skipped. These settings are indicated below with comments. More detail on each setting follows this table. 1. 2. 3. 4. Touch and hold down the SYSTEM and CONFIG TouchPads for 3 seconds. Release both buttons and the first installer setting will be displayed.
PAGE 11
No.
PAGE 12
NOTES - Installer Settings 1 2 3 4 5 6 7 8 9 10 11 Only available if Residential profile was selected in option 1. Only available if a 2, 3 or 4 stage system type was selected in option 6. Only available if a Conventional system was selected in option 6. Only available if a 2, 3 or 4 stage Heat Pump system was selected in option 6. Only available if a Heat Pump system was selected in option 6. Only available if the 24 Volt AC common wire is connected to the C terminal.
PAGE 13
16 AC Power Interrupt Warning [note 6] – When enabled, the thermostat will display an outage warning when AC power to the thermostat is lost. 17 Short Cycle Protection – Selects the number of minutes the cooling compressor will be locked out after turning off. This short cycle protection is also active in the heat mode if a heat pump system was selected in Option 6. 18 Residual Cooling Fan Delay – Selects a delay for the system fan after the cooling compressor has turned off.
PAGE 14
26 Outside Air Intake [note 11] – Selects economizer control options. Select between disabled (NONE), economizer mode (ECON) and time of day (TOD) mode.
PAGE 15
5 System Testing Warning Read Before Testing • Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system control board to test the thermostat installation. This could damage the thermostat and void the warranty. • Do not select the COOL mode of operation if the outside temperature is below 50º F (10º C). This could possibly damage the controlled cooling system and may cause personal injury.
PAGE 16
® Limited Warranty When installed by a professional contractor, this product is backed by a 5 year limited warranty. Limitations apply. For limitations, terms and conditions, you may obtain a full copy of this warranty: · Visit us online: www.braeburnonline.com/warranty · Phone us: 866.268.5599 · Write us: Braeburn Systems LLC 2215 Cornell Avenue Montgomery, IL 60538 Store this manual for future reference.
PAGE 17
Notes
PAGE 18
® Braeburn Systems LLC 2215 Cornell Avenue • Montgomery, IL 60538 Technical Assistance: www.braeburnonline.com Call us toll-free: 866-268-5599 (U.S.) 630-844-1968 (Outside the U.S.) ©2018 Braeburn Systems LLC • All Rights Reserved. Made in China.