Specifications

ManualsBrandsBraeburn ManualsDomestic Appliances6100

Installer Guide

Programmable Touchscreen Thermostats

Speciﬁcations

Installation and Wiring

Quick Reference

Installer Settings

System Testing

To prevent damage to the thermostat, never use a sharp instrument

to press the touchscreen keys. Always press keys with your ﬁngers.

Attention

• Possible electric shock or damage to equipment can occur.

• Disconnect power before beginning installation.

Caution

This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline

batteries for

proper operation. When connecting 24 Volt AC Power the batteries may

be installed as a backup.

For use only as described in this manual. Any other use will void warranty.

6100

Single Stage Heat / Cool Conventional

or Heat Pump

6300

Up to 4 Heat / 2 Cool Heat Pump

Up to 3 Heat / 2 Cool Conventional

6400

Up to 4 Heat / 2 Cool Heat Pump

Up to 3 Heat / 2 Cool Conventional

with Humidity Control

Warning

For installation by experienced service technicians only.

Touchscreen

Summary of content (18 pages)

PAGE 1
® Installer Guide Touchscreen TM Programmable Touchscreen Thermostats 6100 Single Stage Heat / Cool Conventional or Heat Pump 6300 Up to 4 Heat / 2 Cool Heat Pump Up to 3 Heat / 2 Cool Conventional 6400 Up to 4 Heat / 2 Cool Heat Pump Up to 3 Heat / 2 Cool Conventional with Humidity Control 1 Specifications 2 Installation and Wiring 3 Quick Reference 4 Installer Settings 5 System Testing Attention To prevent damage to the thermostat, never use a sharp instrument to press the touchscreen keys.
PAGE 2
1 Specifications This thermostat is compatible with: • • • • Electrical and control specifications: • • • • • • • Single stage heat / cool conventional and heat pump systems Conventional systems up to 3 stages of heating and 2 stages of cooling (6300/6400 only) Heat pump systems up to 4 stages of heating and 2 stages of cooling (6300/6400 only) 250 – 750 millivolt heating only systems Electrical Rating: 24 Volt AC 1 amp maximum load per terminal AC Power: 18 – 30 Volts AC DC Power: 3.
PAGE 3
Install your new Braeburn thermostat in 4 basic steps: 1 2 3 4 Install the sub-base Provide Power Connect your wires Attach the thermostat to the sub-base 1 Install the Sub-Base: • Remove the sub-base from the body of the thermostat. • Mount the sub-base as shown below: Drill 3/16” pilot holes in your desired location. Use supplied anchors for drywall or plaster.
PAGE 4
3 Connecting Your Wires Wiring Terminations for model 6100 Terminal Function Description G Output Fan Control Rc Input 24 Volt AC Cooling Transformer (Dual Transformer Systems Only) Rh Input Power Connection (24 Volt AC Heating Transformer or Millivolt Power Source) W Output 1st Stage Conventional Heat O or B Output Reversing Valve (Cool Active or Heat Active) Y Output 1st Stage Compressor C Input 24 Volt AC Transformer Common S1 Input Optional Remote Sensor (Indoor or Outdoor)
PAGE 5
Conventional Systems Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section. The 6100 is a single stage thermostat and not intended for multi stage equipment.
PAGE 6
Heat Pump Systems Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section. The 6100 is a single stage thermostat and not intended for multi stage equipment.
PAGE 7
All System Types Additional Wiring Options NOTE: Additional options are configured in the Installer Settings section. S1 Indoor or Outdoor Remote Sensor [note 1] S2 Indoor or Outdoor Remote Sensor [note 1] A/D* Economizer Control (6300, 6400 only) / Dehumidifier Output (6400 only) [note 2] H Humidifier Output (6400 only) [note 3] * This terminal appears as A on the 6300 and A/D on the 6400.
PAGE 8
3 Quick Reference 13 12 Instructions 11 1 10 2 9 8 3 14 4 RESET 5 6 15 7 Thermostat Display 1 Room Temperature....................... .Displays the current room temperature 2 Lock Mode Indicator . .................. .Indicates if the thermostat is locked 3 Set Temperature........................... .Displays the current set point temperature 4 Humidity Indicator (6400 only)..... .Indicates when there is a call for humidity 5 Fan Indicator................................. .
PAGE 9
RESET Thermostat TouchPads TM NOTE: Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are the “touch sensitive” segments used to adjust your thermostat. Depending on the equipment installed, all touch pads may not show.
PAGE 10
4 Installer Settings The Installer Settings must be properly configured in order for this thermostat to operate correctly. The Installer Settings are menu driven. The portion of these settings that do not apply to your setup will be skipped. These settings are indicated below with comments. More detail on each setting follows this table. 1. 2. 3. 4. Touch and hold down the SYSTEM and CONFIG TouchPads™ for 3 seconds. Release both buttons and the first installer setting will be displayed.
PAGE 11
No.
PAGE 12
NOTES - Installer Settings 1 2 3 4 5 6 7 8 9 10 11 12 Only available if Residential profile was selected in option 1. Only available if a 2, 3 or 4 stage system type was selected in option 6. Only available if a Conventional system was selected in option 6. Only available if a 2, 3 or 4 stage Heat Pump system was selected in option 6. Only available if a Heat Pump system was selected in option 6. Only available if the 24 Volt AC common wire is connected to the C terminal.
PAGE 13
16 AC Power Interrupt Warning [note 6] – When enabled, the thermostat will display an outage warning when AC power to the thermostat is lost. 17 Short Cycle Protection – Selects the number of minutes the cooling compressor will be locked out after turning off. This short cycle protection is also active in the heat mode if a heat pump system was selected in Option 6. 18 Residual Cooling Fan Delay – Selects a delay for the system fan after the cooling compressor has turned off.
PAGE 14
29 Outside Air Intake [note 12] – Selects economizer control options. Select between disabled (NONE), economizer mode (ECON) and time of day (TOD) mode.
PAGE 15
5 System Testing Warning Read Before Testing • Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system control board to test the thermostat installation. This could damage the thermostat and void the warranty. • Do not select the COOL mode of operation if the outside temperature is below 50º F (10º C). This could possibly damage the controlled cooling system and may cause personal injury.
PAGE 16
® 5 YEAR LIMITED WARRANT Y Store this manual for future reference Limited Warranty Braeburn Systems LLC warrants each new Braeburn thermostat against any defects that are due to faulty material or workmanship for a period of five years after the original date of purchase by a professional service technician.
PAGE 17
Notes
PAGE 18
® Braeburn Systems LLC 2215 Cornell Avenue • Montgomery, IL 60538 Technical Assistance: www.braeburnonline.com Call us toll-free: 866-268-5599 (U.S.) 630-844-1968 (Outside the U.S.