Installation Sheet

12
www.bradleycorp.com
METHOD OF USE
Correct cleaning of the unit will lengthen its working life considerably.
When in use, the machine will accumulate dust inside which should be cleaned out every six months.
PREVENTATIVE MAINTENANCE AND CLEANING
Sensor
3
These models operate by hand detection. Place hands 2-6" (5 - 15 cm) from
the air outlet and the dryer will start working. Once activated, immediately
place hands in air flow and rub together until dry. This machine will stop 2-3
seconds after use.
NOTE: Vandal Resistant Operating System will cause this unit automatically
shut-off if sensor is completely blocked.
1. Preventative maintenance
2. Cleaning Method
Sensored models
1.Turn off power to the unit.
2. Remove cover using security wrench (See Dismantling for Installation).
3. Clean away any accumulated dust on the fan with a soft bristle brush while rotating it manually. Use
the same brush, to clean away all accumulated dust from the other components. Carefully remove
any dust from the electronic circuit board and hand detecting sensors using a fine brush.
4. Use brush to clean the air inlet grill and make sure the LED visor is completely clean.
5. Check the condition of the motor brushes. These should be replaced when they are less than13/64
inches (5 mm.).
6. Reconnect power to the unit and let it run continuosly, removing any excess dust.
7. Turn off power to the unit and install cover per the Mounting Instructions.
Caution: Do not damage or force any components.
Cleaning the cover - Use only a wet cloth to clean the covers. Do not use any kind of detergent, acids,
lye, abrasives, hydrocloric acid, etc.
For Warranty information go to:
www.bradleycorp.com/customerservice/warranty-dryers.jsp
WARRANTY
Sensor
MODO DE EMPLEO
Modelos automáticos
Estos modelos actúan por detección de las manos. Colocar las manos a 2-6"
(5 -15 cm) de la salida de aire y la secadora se pondrá en funcionamiento. Una
vez activada, colocar inmediatamente las manos bajo el flujo de aire y frotarlas
hasta que se sequen. El aparato se detendrá 2-3 segundos después de su
empleo.
NOTA: El Sistema antivandálico desconectará automáticamente este aparato
si el sensor se encuentra completamente bloqueado.
Una adecuada limpieza de la máquina alargará lavida útil de la secadora de manos.
Durante el uso, la máquina acumulará polvo en su interior que se deberá limpiar cada seis meses.
MANTENIMIENTO PREVENTIVO Y LIMPIEZA
1. Mantenimiento preventivo
2. Método de limpieza
1. Desconectar la unidad.
2. Quitar la carcasa con la llave de seguridad (Véase el apartado Desmontaje para la instalación).
3. Limpiar el polvo acumulado en el ventilador con un cepillo de cerdas suave realizando movimientos
rotatorios. Utilizar el mismo cepillo para limpiar todo el polvo acumulado en los demás componentes.
Eliminar con cuidado el polvo presente en cualquier placa electrónica y en los sensores de detección
de las manos con un cepillo fino.
4. Utilizar el cepillo para limpiar la rejilla de entrada de aire y comprobar que el visor LED esté
completamente limpio.
5. Comprobar el estado de las escobillas del motor. Se deberán sustituir cuando tengan una longitud
inferior a13/64 pulgadas (5 mm).
6. Volver a conectar la unidad a la alimentación eléctrica y hacerla funcionar continuamente, hasta que
no salgan restos de polvo por la salida de aire.
7. Apagar la unidad e instalar la carcasa según las instrucciones de montaje.
Precaución: no dañar ni forzar los componentes.
Limpieza de la carcasa - Usar únicamente un trapo húmedo para limpiar la carcasa. No utilizar ningún
tipo de detergente, ácidos, lejía, abrasivos, ácido clorhídrico, etc.
Para información sobre la garantía entrar en:
www.bradleycorp.com/customerservice/warranty-dryers.jsp
GARANTÍA