Night Stand Contains One (1) Night Stand and Hardware IMPORTANT NOTE: Carefully remove all the parts from the box, Arrange on a flat TOOLS REQUIRED: surface and verify you have all of the following parts and hardware -Phillips Screwdriver 1.Top Panel (1 PC) 2. Left Side Panel (1 PC) 3.Right Side Panel (1 PC) 4.Bottom Panel (1 PC) 5.Top Front Bar Panel 6.Top Back Bar Panel 7.Back Panel (1 PC) 8.Small Drawer Front Panel 9.Small Drawer Back } ( I Panel (1 PC) 10.Small Drawer Side Panel ~~ 11.
HARDWARE LIST A.Allen Key (1 PC) Se D. Minifix House (13 PCS) Ge | G.Screw 50mm (16 PCS) pa J.Drawer Slider (2 SET) mE B.Dowel (10 PCS) x E. Minifix Cap (13 PCS) H.L Bracket (4 PCS) K.White Nail (4 PCS) C. Minifix Bolt (13 PCS) F.
ASSEMBLY INSTRUCTIONS Tap Dowels (Part B) into the Top Panel STEP 1 (Part Panel (Part 4) and Top Back Bar Panel (Part 6) in the larger holes provided.Insert Mini fix House (Part E) into the Top Panel, Top Back Panel and Bottom Panels (Part 1,4 and 6) as shown.Ensure the open side of the Mini fix House is facing the opening on the left and right side of the panels. Attach the Drawer Slider (Part J) to STEP 2 the Left Side Panel (Part 2) using Screw 16mm (Part the © Pilot Hole as marked.
ASSEMBLY INSTRUCTIONS STEP 3 = Attach the Drawer Slider {Part J} to the Right Side d Panel (Part 3} using Screw 16mm (Part the Pilot Hole as marked.
ASSEMBLY INSTRUCTIONS STEP 5 This is how a mini fix works... Attach the Top Back Bar Panel (Part 6) to the CB ing ou i open Right Side Panel (Part 3) as shown. Tum the €. oe a evo Mini fix House (Part D}) to tighten using the Allen “Wy, | hoeing mot antigenic Key or screwdriver.Cover the Mini fix House using over th mind fix bolt. the Mini fix Cap (Part E) by pressing it into the Mini fix House. *Attach Minimum Cap as shown. STEP 6 ‘This is how & mini fix works...
ASSEMBLY INSTRUCTIONS STEP 7 — — Attach the Bottom Panel (Part 4) to the hiss how a mia fx works. Right Side Panel (Part 3) as shown. Tum the #7 housing goes into the open. Mini fix House (Part D} to tighten using the Allen a ee Key or screwdriver .Cover the Mini fix House Soi L housing so it tightens using the Mini fix Cap (Part E) by pressing it into the Mini fix House. oo *Attach Mini fix Cap as shown.
ASSEMBLY INSTRUCTIONS STEP 9 *Attach Mini fix Cap as shown. ‘This is how a mini fix works... ‘The head of fhe mini fix ‘housing pos into the pane ‘mouth of the mini fix bolt “You then tym the mini fix housing so i tightens over tho mini fix bolt. Attach the Left Side Panel (Part 2) to the Bottom Panel (Part 4) and Top Panel (Part 1) as shown. Turn the Mini fix House (Part D) to tighten using the Allen Key or screwdriver.
ASSEMBLY INSTRUCTIONS STEP 11 Attach the White Nail (Part K) to the Bottom Panel (Part 4) by either pushing them in with your hand or using a mallet/hammer. STEP 12 Attach L Bracket (Part H) to each corner of the Back Panel (Part 7) using Screw 16mm (Part F) as shown.
ASSEMBLY INSTRUCTIONS STEP 13 Attach the Small Drawer Side Panels (Part 10) to the Small Drawer Front Panel (Part 8) using Screw 50mm (part G). Insert the Drawer Bottom Panel (Part 11) as shown. Attach the Small Drawer Back Panel (Part 9) by using Screw 50mm (Part G) as shown. Attach the slider (Part J) to the bottom of the drawer sides using Screw 16mm (Part F) as shown.
ASSEMBLY INSTRUCTIONS STEP 15 Attach the Large Drawer Side Panels (Part 14) to the Large Drawer Front Panel (Part 12) using Screw 50mm (Part G). Insert the Drawer Bottom Panel (Part 11) as shown. Attach the Large Drawer Back Panel (Part 13) by using Screw 50mm (Part G) as shown. Attach the slider (Part J) to the bottom of the drawer sides using Screw 16mm (Part F) as shown.