Use And Care Manual

ManualsBrandsBostitch ManualsAir Nailers & Staplers16-Gauge Pneumatic Medium Crown Siding & Sheathing Stapler

651 SERIES

PNEUMATIC STAPLER

ENGRAPADORA NEUMÁTICA

AGRAFEUSE

189863RA 04/10

STANLEY FASTENING SYSTEMS L.P.

OPERATION and MAINTENANCE MANUAL

MANUAL DE OPERACIÓNY DE MANTENIMIENTO

MANUEL D’INSTRUCTIONS ET D’ENTRETIEN

BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO

UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE

INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,

CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.

ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR

ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE

SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA

HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON

SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR.

LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE

ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX

AVERTISSEMENTS. GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS

AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE

BOSTITCH.

Summary of content (13 pages)

PAGE 1
651 SERIES PNEUMATIC STAPLER ENGRAPADORA NEUMÁTICA AGRAFEUSE OPERATION and MAINTENANCE MANUAL MANUAL DE OPERACIÓN Y DE MANTENIMIENTO MANUEL D’INSTRUCTIONS ET D’ENTRETIEN BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
PAGE 2
INTRODUCTION Bostitch pneumatic tools are precision-built, and designed for high speed/high volume fastening. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before operating the tool and understand the safety warnings and cautions.
PAGE 3
SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
PAGE 4
MAINTAINING THE TOOL When working on air tools note the warnings in this manual and use extra care when evaluating problem tools. TOOL SPECIFICATIONS All dimensions in inches unless otherwise specified. 651S5 7/16” Crown Stapler 70-120 PSI (4.9 to 8.43kg/cm2) 16S5 & 17S5 Series Staples 16 & 17 Gauge 1” to 2” (25mm to 50mm) 120 14” Description Operation Pressure Range Fastener Type Fastener Gauge Fastener Range Magazine Capacity Length Width Height Weight 3 1/8” 11” 4.3 lbs.
PAGE 5
OPERATING MODES Always disconnect air supply before making adjustments as accidental actuation may occur, possibly causing injury. BOSTITCH OFFERS TWO MODES OF OPERATION FOR THIS SERIES TOOL. CONTACT TRIP: The common operation procedure on “Contact Trip” tools is for the operator to contact the work surface to actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work surface is contacted. This will allow rapid fastener placement on many jobs.
PAGE 6
AIR SUPPLY AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses should have a minimum of 150 p.s.i. (10.6 kg/cm2) working pressure rating or 150 percent of the maximum pressure that could be produced in the air system.
PAGE 7
LOADING THE 651 STAPLER EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
PAGE 8
FASTENER DEPTH CONTROL ADJUSTMENT Always disconnect air supply: 1) Before making adjustments; 2) When servicing the tool; 3) When clearing a jam; 4) When tool is not in use; 5) When moving to a different work area, as accidental actuation may occur, possibly causing injury. The Fastener Depth Control Adjustment feature provides control of the staple drive depth from flush with or just above the work surface to shallow or deep countersink.
PAGE 9
TOOL OPERATION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
PAGE 10
TOOL OPERATION (CONTINUED) The Contact Trip will not prevent a nail from being accidentally driven if the trigger is depressed and the “trip” is bumped against any object or person. Never hold or carry the tool with your finger on the trigger. Only depress and hold trigger when you intend to rapidly drive multiple nails and the tool is pointed at the work surface.
PAGE 11
TOOL OPERATION CHECK CAUTION: Remove all fasteners from tool before performing tool operation check. 1. CONTACT TRIP OPERATION: A. With finger off the trigger, press the contact trip against the work surface. THE TOOL MUST NOT CYCLE. B. Hold the tool off the work surface, and pull the trigger. THE TOOL MUST NOT CYCLE. C. With the tool off the work surface, pull the trigger. Press the contact trip against the work surface. THE TOOL MUST CYCLE. D.
PAGE 12
TROUBLE SHOOTING PROBLEM CAUSE Trigger valve housing l eaks air O-ring cut or cracked . . . . . . . . . . . . . . . . . . . . .Replace O-ring CORRECTION Trigger valve stem leaks air O-ring/seals cut or cracked . . . . . . . . . . . . . . . . .Replace trigger valve assembly Frame/nose leaks air Loose nose screws . . . . . . . . . . . . . . . . . . . . . . .Tighten and recheck O-ring or Gasket is cut or cracked . . . . . . . . . . .Replace O-ring or gasket Bumper cracked/worn . . . . . . . . . . . . .
PAGE 13
AVAILABLE ACCESSORIES 651-RB1 651 O-RING KIT TVA6 TRIGGER VALVE KIT PREMOIL-4OZ PREMIUM PNEUMATIC TOOL OIL 16S5 SERIES STAPLES VSA5 VINYL SIDING ADAPTER PRO-3850 & PRO-1450 PREMIUM POLYURETHANE AIR HOSE -13-