3FHJTU FS \RXU QHZ GH YLFH RQ 0\%RV FK QRZ DQG JHW IUH H EHQH ILWV CPTDI IPNF XFMDP DPN NF Extractor hood [en] Instructions for installation and use Extractor hood
en Table of contents [en]I nst r uct i ons f or i nst al at i on and useExt r act or ho d INSTRUCTION MANUAL.......................................................... 2 8 Intended use ..........................................................2 ( Important safety information ...............................3 7 Environmental protection.....................................4 Ç Operating modes...................................................4 1 Operating the appliance .......................................
Important safety information en (Important safety information :Warning – Danger of suffocation! Packaging material is dangerous to children. Never allow children to play with packaging material. I mpor t ant saf et y i nf or mat i on : Warning – Danger of death! Risk of poisoning from flue gases that are drawn back in. Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room airdependent heat-producing appliance is being operated.
en Environmental protection : Warning – Risk of injury! Components inside the appliance may have sharp edges. Wear protective gloves. Risk of injury! ■ Items placed on the appliance may fall down. Do not place any objects on the appliance. Risk of injury! ■ The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.
Operating the appliance Air recirculation The air which is drawn in is cleaned by the grease filters and an activated carbon filter, and is conveyed back into the kitchen. Note: To bind odours in air recirculation mode, you must install an activated carbon filter. The different options for operating the appliance in air recirculation mode can be found in the brochure. Alternatively, ask your dealer.
en Cleaning and maintenance Follow all instructions and warnings included with the cleaning agents. Area Stainless steel Cleaning agent Hot soapy water: Clean with a dish cloth and then dry with a soft cloth. Clean stainless steel surfaces in the grind direction only. Special stainless steel cleaning products are available from our after-sales service or from specialist retailers. Apply a very thin layer of the cleaning product with a soft cloth.
Trouble shooting On appliances with a glass plate in the filter pull-out: ■ ■ The glass plate can be removed easily and can be cleaned in the dishwasher. To remove it, carefully lift the glass plate. en Replacing bulbs These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. : Warning – Risk of burns! Halogen bulbs become very hot when switched on.
en Customer service 4Customer service Accessories When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access). You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.
Installation instructions en INSTALLATION INSTRUCTIONS I nst al at i on i nst r uct i onsInstallation instructions These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. ■ ■ ■ This appliance is installed in a upper cabinet. Follow the enclosed installation instructions for additional special accessories (e.g. for circulating-air mode). The surfaces of the appliance are sensitive.
en Important safety information (Important safety information Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.
General information : Warning – Risk of fire! Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, the largest specified distance applies. Only one side of the appliance may be installed directly next to a high-sided unit or a wall.
General information en Electrical connection : Warning – Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation. The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal mesh grease filter. Length of the cable: approx. 1.30 m This appliance complies with the EC interference suppression regulations. 1.
Installation Body wall thickness: 16 mm 1. Screw the mounting pieces to the body on the left and right. ¨ 2. Remove the tabs from the bottom of the mounting pieces. © en 2. Connect the power cord provided to the appliance.¨ 3. Use the strain relief to secure the power cord in place.© $ $ PP % % PP [ Body wall thickness: 19 mm 1. Fold out the tabs on both of the mounting pieces. ¨ 2. Screw the mounting pieces to the body on the left and right. © 3.
Installation en 4. Screw in the filler strip fully. Sliding out the appliance Note: Before you remove the appliance, protect the hob with a piece of polystyrene from the packaging. PP [ 1. Use a flat-blade screwdriver to push in the fastening bolt, and turn it 90° until it locks into place. ¨ 2. Push in the fastening bolt gently with your fingers, and turn it until it comes out of the housing along with the spring.
Installation Appliance width 90 cm: You must also screw the appliance to the wall-hanging cupboards either side of it. en Connecting the pipes Note: If an aluminium pipe is used, smooth the area where it is to be connected before you connect it. Exhaust air pipe, dia. 150 mm (recommended size) Fit the exhaust air pipe directly to the air-pipe connector and seal the joint. Exhaust air pipe, dia. 120 mm 1. Fit the reducing connector directly to the air-pipe connector. 2.
5IBOL ZPV GPS CVZJOH B #PTDI )PNF "QQMJBODF 5HJLVWHU \RXU QHZ GHYLFH RQ 0\%RVFK QRZ DQG SURILW GLUHFWO\ IURP t &YQFSU UJQT USJDLT GPS ZPVS BQQMJBODF t 8BSSBOUZ FYUFOTJPO PQUJPOT t %JTDPVOUT GPS BDDFTTPSJFT TQBSF QBSUT t %JHJUBM NBOVBM BOE BMM BQQMJBODF EBUB BU IBOE t &BTZ BDDFTT UP #PTDI )PNF "QQMJBODFT 4FSWJDF )UHH DQG HDV\ UHJLVWUDWLRQ ² DOVR RQ PRELOH SKRQHV XXX CPTDI IPNF DPN XFMDPNF -PPLJOH GPS IFMQ :PV}MM GJOE JU IFSF ([SHUW DGYLFH IRU \RXU %RVFK KRPH DSSOLDQFHV QHHG KHOS ZLWK SUREOHPV RU
