Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
B93x/B94x keypads configuration of IPv6 Server Address
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [2] Network > [1] Ethernet > (choose the bus module or on-board) >
[3] DNS Parameters > [2] IPv6 Server Address. The keypad shows the DHCP/AutoIP
current configuration.
3. Press [IPv6 Server Address] to edit the IP address.
4. Delete the existing number, if necessary, and then enter the new number. Use
/[PREV]
or /[NEXT] to move to a different byte.
5. Press [Save] to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
Module Hostname
B91x/B92x keypads configuration of Module Hostname
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [2] Network > [1] Ethernet > (choose the bus module or on-board) >
[3] DNS Parameters > [3] Module Hostname. The keypad shows the IPv4 Server Address
current configuration.
3. Press [ENTER] to edit the hostname.
4. Delete existing characters, if necessary, and then enter the new characters.
5. Press [ENTER] to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
B93x/B94x keypads configuration of Module Hostname
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [2] Network > [1] Ethernet > (choose the bus module or on-board) >
[3] DNS Parameters > [3] Module Hostname. The keypad shows the DHCP/AutoIP current
configuration.
3. Press [Module Hostname] to edit the hostname
4. Delete existing characters, if necessary, and then enter the new characters.
5. Press [Save] to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
[2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in
module)
You can use a B44x cellular communication module for communication. Plug it directly into the
control panel or use it with a B450 module.
Module 1settings Module 2 settings
SIM APN _______________________________ _______________________________
SIM Username _______________________________ _______________________________
SIM Passcode _______________________________ _______________________________
SIM PIN _______________________________ _______________________________
SIM APN
B91x/B92x keypads configuration of SIM APN
1. Enter the installer passcode, and then open the [1] Installer menu.
20.1.8
Control Panel Keypad Installer menu | en 119
Bosch Security Systems, Inc. Installation and System Reference Guide 2016.05 | 14 | F.01U.287.180