Bona MiniEdge Manual and safety instructions in original AMO260000.3 | AMO260001.0 | AMO260001.3 | AMO260003.3 Translation of manual in originals v1.
Bona MiniEdge TECHNICAL DATA Motor type: Voltage (+/- 10%): Frequency: Power: Rated current: Recommended fuses: Isolation class: Safety class: Sanding disc speed: Illumination: Total weight: Dust discharge: Abrasive disc diameter: Sanding arm height: Hour meter: EU 1-fasmotor 230V 50/60 Hz 1,3 kW 6A 10A F IP54 Ca 3 800 rpm normal load 25W halogen 9 kg < 2 mg/m³ air 150mm 145mm, 245mm 99 999 timmar USA 1-phasemotor 115V 60 Hz 1-3/4 HP 15A 20A F IP54 4400 rpm normal load 25W halogen 18,7 lbs < 2 mg/m³ air
Bona MiniEdge DANGER means that you or other staff can suffer a serious injury or death if THE INSTRUCTIONS MARKED WITH DANGER ON THIS MACHINE OR IN THESE USER INSTRUCTIONS are ignored or are not followed. Read the entire user manual before you use the machine. WARNING means that you or other staff can suffer an injury if the instructions marked with WARNING on this machine or in this user manual are ignored or not followed.
Bona MiniEdge The operator or other persons present can be injured if the power to the machine is connected while maintenance is performed, or while a tool is changed. Because dust from sanding (i.e. red lead, certain types of wood and metals) are hazardous to health, a face mask of at least class P2 must be used. There is a risk of damage to the eyes and/or body if protective clothing and/or protective equipment is not used during sanding.
Bona MiniEdge Do not forget to put the on the tool before you start the machine. Always check that the sanding paper is correctly adjusted before you begin sanding. Keep the handle clean and free from grease. Keep unauthorised persons away from the work site. Do not allow unauthorised persons to come into contact with the machine or power cables. Do not misuse the machine. The machine works better when it is used according to its capacity and design. Allow the motor to “rest” during periods of heavier use.
Bona MiniEdge Repairs, Service and Maintenance Service Bona MiniEdge is a high quality machine and is tested by authorised test personnel at the factory before delivery. However, electrical and mechanical parts wear down and age during long-term use. In order to keep the machine in a safe and functioning condition, service must be performed every 250 work hours or at least once a year.
Bona MiniEdge Warranty A 24 month factory warranty (from the date of invoice) against material and manufacturing faults applies to Bona Division Sanding’s own manufactured machines and Bona DCS with accessories manufactured after 01-01-2008. Bona Division Sanding pledges to rectify material and manufacturing faults free of charge provided that the machine, with paid freight, is sent to us with the relevant warranty claim form describing the fault. The factory warranty only covers new sales.
Bona MiniEdge The main function of the machine is to serve as a complement to a belt or a drum sander for sanding edges. The machine is designed in accordance with latest information regarding ergonomics, safety and efficiency. The machine has been thoroughly checked and approved before leaving the factory. ASSEMBLY (Pict. 1) 1 Push the dust tube into the dust bag. Tighten the dust bag with the Velcro band on the tube. Put the dust bag with the dust tube back into the hole on the motor bracket . N.B.
Bona MiniEdge Machine adjustment (Pict. 4-5) 4 The machine is designed to angled forwards with an angle of approx. 4°. The distance between the underside of the motor bracket and the floor should be 58 mm. . This is achieved by adjusting the wheels using the adjusting screws. Correct adjustment of the machine is very important, as only approx. 1/3 of the disc should be in contact with the floor. The simplest way of checking this is to make a sanding proof.
Bona MiniEdge Changing sanding discs Never start the machine before a sanding disc is attached. N.B. Always use sanding discs of high quality in the correct dimension with a stable back side. N.B. Check the sanding disc regularly. If the sanding disc is worn out or has become clogged by lacquer or paint, the sanding result deteriorates and there is less efficient and the surface of wood may become discoloured. N.B. Only abrasive paper for sanding of wooden floors shall be used.
Bona MiniEdge SERVICE AND MAINTENANCE All maintenance must be made on an unconnected machine Check that the cable keeps an area of at least (120V 3xAWG14 Article no: ASO901527) or (230V 3 x 1,5mm2 Article no: ASO908215). If the cable is too weak the motor can be overloaded and be damaged. If the power supply is too weak the motor can be overloaded and damaged. Avoid prolonged or very hard sanding as will cause the motor to become very hot.
Bona MiniEdge Reassembly (Pict. 15 -18) Distance of gap Line-up the holes consistently 15 Place the new belt on the belt pulley. Twist the Bearing house while holding the pulley in such way that the distance between the bearing housing and the pulley is the biggest and the holes line up consistently. (See picture15) Place the whole package as it is, into the sanding arm, do not fasten the bearing house. Baring house and plate hub against each other with accompanied Textron wrench T15.
Bona MiniEdge Carbon brushes (Pict. 20-22) 20 21 19 22 The task of the carbon brushes is to transport the power to the armature via the rotating collector. There are two carbon brushes. They should be checked regularly and changed in pairs after approx. 100 hours normal operating time. N.B. Carbon brushes wear more quickly when subjected to high loads. Exchange: Unplug the machine. Remove the plastic covers from the machine front cover. Unscrew the two black coal covers on the machine housing.
Bona MiniEdge Changing wheel bracket, complete wheel (Pict. 25) When you wish to change complete wheel do as follows: Insert the Allen key in the key in the socket on the shaft, use a universal pliers and pull the wheel adjusting anti-clockwise. Loosen the wheel locking completely and unscrew the wheel nut from the motor bracket. Do in the opposite way when assembling the new wheel bracket.
Bona MiniEdge Trouble shooting Fault Cause Action The machine doesn’t start No power. Cable broken. Rotation of the disc is impossible Change to another wall socket. Change the cable. Rotate the sanding disc, remove possible blockages. Check that the ventilator runs smoothly. Adjust the ventilator. The sanding disc doesn’t rotate The cogged belt is broken/worn out. Change the cogged belt. The machine is faltering The carbon brushes are worn out. The carbon brackets are broken.
Bona MiniEdge SAFETY INSTRUCTIONS FOR USE OF BONA EDGE MACHINES IMPORTANT! During use of electrical machinery, basic safety precautions should be followed in order to reduce the risk of fire, electrical accidents or personal injury. Therefore, read the following instructions thoroughly before the machine is used. Save the instructions. Always use an earth circuit breaker! 1. For safer use, keep the work area clean. An untidy work area increases risk for accidents. 2. Consider the surroundings.
Bona MiniEdge division Sanding Vallgatan 45, SE-716 31 Fjugesta, Sweden Tel.: +46 (0)40 38 73 90 Fax: +46 (0)585 204 Please visit: www.bona.
Bona MiniEdge Bona AB, Division Sanding Vallgatan 45, SE-716 31 Fjugesta, Sweden Tel.: +46 (0)40 38 73 90 Fax: +46 (0)585 204 Bona AB Box 21074, SE-200 21 Malmö, Sweden Tel.: +46 (0)40 38 55 00 www.bona.com EU assurance of conformity As per directive 2006/42/EC, appendix IIA We hereby guarantee that Bona MiniEdge with article number: AMO260000.3 | AMO260001.0 | AMO260001.3 | AMO260003.
