Installation Guide
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 01/12/18 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2018 by Bobrick Washroom Equipment, Inc.
Technical Data
Mount Within 12" 305mm
of Front of Toilet Seat
10-21/32"
271mm
Viewing Slot
1"
25mm
Ty p.
1-43/64"
45mm
S S
S
S
S
3-11/32"
85mm
5-11/32"
135mm
1/2"
12mm
Ty p.
3-1/8"
80mm
6-5/8"
170mm
9-1/8"
230mm
Finish Wall
Door
Lock
4-29/64"
115mm
Pivot Point
10-45/64"
270mm
Back Plate
Reccommended Mounting Height Off Floor
29-1/2" 750mm
SURFACE-MOUNTED
SINGLE JUMBO-ROLL
TOILET TISSUE DISPENSER
MATERIAL:
Mounting Plate — 16-gauge (1.6mm) stainless steel.
Door — Type-304, 22-gauge (0.8mm) stainless steel with satin-fi nish. Slot reveals toilet tissue supply inside cabinet. Equipped with a
lock keyed like other Bobrick Washroom Equipment accessories.
Spindle — Removable rubber-o-rings converts to smaller spindle. Fixed inner spindle, 20 gauge (0.9mm) stainless steel.
OPERATION:
Door unlocks with key provided and swings down for loading dispenser. Spindle adapter accommodates one toilet tissue roll up to
10" (255mm) diameter with a 1-5/8" (40mm) diameter core roll; convertible for 3" (75mm) diameter core rolls. Rubber o-rings (2)
(furnished by manufacturer) may be added to the steel inner spindle to accommodate a 2-1/8" (55mm) diameter core roll. Wide
viewing slot in door reveals the amount of toilet tissue on roll. Unit is designed for quick reloading.
INSTALLATION:
Mount unit on wall or toilet partition with sheet-metal screws at points indicated by an S. Rear edge of unit should be 20" (510mm) from
back wall. This locates toilet tissue within 12" (305mm) of front of standard toilet that projects 30" (305mm) from back wall.
For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure with sheet-metal
screws (not furnished). For other wall surfaces, provide fi ber plugs or expansion shields for use with sheet-metal screws (not
furnished), or provide 6mm (1/4") toggle bolts or expansion bolts.
For partitions with particle-board or other solid core, secure with sheet-metal screws (not furnished), or provide through-bolts, nuts,
and washers. For hollow-core metal partitions, provide solid backing into which the sheet-metal screws can be secured. If two units are
installed back-to-back, then provide threaded sleeves and machine screws for the full thickness of partition.
SPECIFICATION:
Single jumbo-roll toilet tissue dispenser door shall be 22-gauge (0.8mm) stainless steel with satin-fi nish. Door shall be equipped with a
lock keyed like other Bobrick washroom accessories. Door shall have a slot to reveal toilet tissue supply inside cabinet. Spindle shall
accommodate one toilet tissue roll up to 10" (255mm) diameter with a 1-5/8" (40mm) diameter core roll convertable for 3" (75mm)
diameter core rolls or 2-1/8" (55mm) diameter core roll by adding rubber o-rings (2) furnished.
Single Jumbo-Roll Toilet Tissue Dispenser shall be Model B-2890 of Bobrick Washroom Equipment, Inc., Clifton Park,
New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario;
Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.
B-2890
Note: Dispenser is ICC A117.1 - 2009 Standard
for Accessibility compliant. Unit can be located
below grab bar, in area 24" minimum to 42"
maximum from rear wall, with outlet 18"
minimum above fl oor.