Blaze Drop-In Single Side Burner Manual
Table Of Contents
- USE & CARE GUIDE
- ATTENTION:
- INSTALLER: PLEASE LEAVE THESE INSTRUCTIONS WITH THE CONSUMER.
- I. Burner Specifications 4
- II. General Safety and Installation Warnings 5-8
- i. Location of Appliance 8-10
- III. Electrical Safety and Installation Warnings 11-12
- IV. Gas Safety and Installation Warnings 12-13
- i. Checking for Gas Leaks 14-16
- ii. Unpacking Unit 16
- V. Gas Connections 17
- i. Natural Gas Requirements 17
- ii. Liquid Propane Gas and Tank Requirements 17-18
- iii. Transporting and Storing LP Gas 18-19
- VI. Installing the Appliance in a BBQ Island 20
- i. Outdoor Kitchen Ventilation 21-23
- ii. Building BBQ Specifications + Instruction Diagrams 23-24
- VII. First Time Operation 25
- i. Lighting the Appliance 25-26
- ii. Manually Lighting the Appliance 26
- iii. Flame Adjustment 26-27
- VIII. Cleaning your Appliance 27-28
- NOTE: ALWAYS have equipment measured by Contractor before beginning any project.
- Single Side Burner Cut Out
- Do not attempt to heat unopened containers on the burner as pressure may build up and cause the container to explode.
- Never use charcoal or any other solid fuel in the appliance.
- Never cook without the drip pan in place.
- Never operate this appliance while under the influence of alcohol or drugs.
- Location of Appliance
- Gas Safety and Installation Warnings
- IMPORTANT: Never connect the appliance to an unregulated gas supply.
- If there are local codes that apply to outdoor burners, you will have to conform to them. Installation must conform with local codes or in the absence of local codes, to the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and Natural Gas Installation Code...
- Leak Testing
- NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS.
- Natural Gas Requirements
- Liquid Propane (LP) Gas and Tank Requirements
- Installing the Appliance in a BBQ Island
- FIRST TIME OPERATION
- Cleaning Your Appliance
- Fuel Conversion
- Blaze Outdoor Products, Warranty Registration, 6620 Greenwell Springs Rd.
- Baton Rouge, LA 70805
BLAZE Instructional Book
Page | 30
Fuel (Gas) Conversion Instructions for BLAZE Gas Burners.
There will be an orifice conversion kit in each Side Burner appropriate for the opposite gas type. The kit
will include the office to be replaced.
CAUTION: This should only by performed by a licensed gas professional.
Burners:
1.
You must remove the cooking grate to expose the main burner in the appliance.
2.
Pull up slightly on side burner head and rotate to the side. This will expose the orifice where the
gas enters into the burner. (pic below)
3.
Remove orifice and replace with orifice of desired gas type and reassemble.
4.
If unsure of full procedure please contact your dealer.
Troubleshooting
Smell of Gas is Present
Check for loose connections or cracks in the gas line. Perform a leak test
with soapy water or a leak testing solution. DO NOT TRY AND TEST WITH
A FLAME. If you find a leak, immediately shut off the gas supply and call a gas
professional to fix the problem.
Burner Does Not Ignite
Check position of
igniting pin.
It should jump over to the brass burner.
Clean area where contact will be made from spark tip to burner. Make sure
there is a blue spark at the electrode tip to burner. Make sure the wire is
connected correctly. Make sure the orifice is free of any grease or dirt.
Make sure burner “slit” is aligned with igniter.
ALWAYS TURN OFF GAS WHEN TESTING
Yellow Flame
Color on flame should be mostly blue. There should be a yellow tip
but if flame is completely yellow, clean burner and substances around
burner to remove oil or debris on the burner, burner pedestal or orifice.
Plugged Orifice
Remove orifice and clean with a fine wire.
No Gas To Burner
Check shut off valve to see if it is in the ON position – gas may be turned
off.