User's Manual
Table Of Contents
- 1. Safety Instructions
- 2. Getting Started
- 2.1 Baby Unit Power Supply
- 2.2 Parent Unit Battery Installation
- 2.3 Parent Unit Power Supply
- 2.4 Desktop Stand of the Parent Unit
- 3. Using the Baby Monitor
- 3.1 Setting Up
- 3.2 Night Vision Mode
- 3.3 Video ON/OFF
- 3.4 Talk Mode
- 3.5 Temperature Display (HH °C / °F or LL °C / °F)
- 4. Parent Unit Menu Options
- 4.1 Adjust Speaker Volume
- 4.2 LCD Brightness
- 4.3 Set Alarm Time on the Parent Unit
- 4.3.1 Set lullaby
- 4.4 Monitor the Temperature
- 4.4.1 Temperature Format
- 4.5 Remove a Baby Unit
- 4.6 Set Screen Off time for the Parent Unit
- 4.7 Zoom, Pan or Tilt
- 4.8 Pair and Replace a Baby Unit
- 4.9 Multi-Camera Use
- 5. Wi-Fi® Internet Viewing
- 5.1 Minimum System Requirements
- 5.2 Getting Started - Connecting Devices
- 5.2.1 Setup
- 5.3 User Account and Camera Setup on Android™ Devices
- 5.3.1 Power ON and Connect the Camera
- 5.3.2 Download Hubble for Motorola Monitors App
- 5.3.3 Run Hubble for Motorola Monitors App on Android™ device
- 5.3.4 Add the Camera to your account
- 5.4 User Account and Camera Setup on iPhone®/iPad®
- 5.4.1 Power ON and Connect the Camera
- 5.4.2 Download Hubble for Motorola Monitors App
- 5.4.3 Run Hubble for Motorola Monitors App on iPhone®/iPad®
- 5.4.4 Add the Camera to your account
- 5.5 Camera Functions:
- 5.5.1 Connecting the Camera Unit to power
- 5.5.2 Overview of the Features on Hubble App
- 5.6 Working with PC/Notebook
- 5.7 Procedure for Resetting the Camera
- 6. Disposal of the Device (Environment)
- 7. Cleaning
- 8. Help
- 9. General Information
- 10. Technical Specifications
Help 37
ENGLISH
8. Help
Display
No display
• Try recharging or replacing the battery pack.
• Reset the Units. Disconnect the battery pack of the Parent Unit and unplug
both the Units' electrical power, then plug them back in.
• Is the Unit turned on?
Press and hold the ON/OFF button on the Parent Unit to turn it ON.
• Is the correct camera selected? Change the camera number, if necessary.
• Is the video display turned on? Press the VIDEO ON/OFF button
to turn it
ON.
• When operating using batteries only, the display will go blank after 5 minutes
or 30 minutes or 60 minutes to save power (depending on video settings).
The Unit is still active and will give you audio alerts. You can reactivate the
screen by pressing any button.
Registration
If the Baby Unit has lost its link with the Parent Unit
• Try recharging or replacing the battery pack.
• If the Baby Unit is too far away it may be going out of range, so move the
Baby Unit closer to the Parent Unit.
• Reset the Units by disconnecting them from the battery and electrical power.
Wait about 15 seconds before reconnecting. Allow up to one minute for the
Baby Unit and the Parent Unit to synchronize.
• See 2.4 Registration (Pairing), if there is a need to re-register the Units.
Interference
Noise interference on your Parent Unit
• Your Baby and Parent Units may be too close. Move them further apart.
• Make sure there is at least 3 to 6ft (1 to 2m) between the 2 Units to avoid
audio feedback.
• lf the Baby Unit is too far away, it may be out of range. Move the Baby Unit
closer to the Parent Unit.