Intelligent Bidet Toilet USER MANUAL BM-5000-E This unit should be installed according to this manual. Read this manual carefully and install properly. Do not attempt to service this unit yourself. Doing so could void your warranty.
IMPORTANT SAFEGUARDS When using electronics, basic safety precautions should always be followed, especially when children are present. READ ALL INSTRUCTIONS BEFORE USING. WARNING To reduce the risk of electrical shock, burns, fire, or injury: 1. Children and people that need assistance should be closely supervised when near to or using product. 2. Product should only be used as described in this manual. Do not use attachments not recommended by manufacturer. 3.
TABLE OF CONTENTS Functions 1 Parts § Controls... 2 Remote . 3 Warnings & Safety. 4 Installation... 8 Before you Install... 9 Installing Your Product... 10 Function Explanations... 14 Maintenance... 16 Troubleshooting 177 Specifications... 19 Warranty 20 BidetMate.
FUNCTIONS Remote Control Side Control Knob Unlimited Cleaning Rear Cleaning Feminine Cleaning Aerated Cleaning Automatic Cleaning Oscillating Cleaning Hot/Cold Massage Cleaning Water Pressure Adjustment Water Temperature Adjustment Bidet Wand Position Adjustment Removable Nozzle Nozzle Self-Cleaning Seat Sensor Heated Seat Heated Dryer Dryer Speed Adjustment Dryer Temperature Adjustment Cyclone-Dir Technology Dryer Damper Slow Down Instant Water Heating Night Light Pr-Flush Flush While Air Drying Remote Flu
PARTS AND CONTROLS Overview, Control Knob, Remote Control OVERVIEW Caution Label Control Knob Grounded Power Plug T-valve Water valve Hose Control Knob ‘Warm Dryer Nozzle (Rear & Front wash} Heated Seat Rotated forward (REAR WASH) Rotated backward (FRONT WASH) BidetMate.
Stop Front Wash Feminine Wash Rear Wash ‘Warm Air Dryer Hands-Free Flush or Rear Wash Crass multiple times to adjust spud, low/mad/hight Decrease the Water ~~ Nozzle position For manual Alternate cleaning Night light lighting Pressure of the Rear can be adjusted nozzle cleaning with hot and cold on or off and Front Wash in 5 positions | water temperature i il —L Cooke Gore Pairing Insbeuetfone: 1 Bugging the beet | 2 Press and held the hep Watson ud the lobes Beige hw pug kts the connote a the bl Uk url ght
EARNINGS AND SAFETY Please Read Thoroughly First of all, thank you for purchasing our product. To ensure proper and safe use of this product, carefully read this section prior to any usage. Afterwards, store this manual in a safe place for any needed future reference. The hazards and warnings listed herein are important to our user's safety. Significant consequences may result from failure to heed warnings.
EARNINGS AND SAFETY This product needs to be properly Do not dispose of or use lit cigarettes, grounded. matches, or other burning objects into ¥Risk of electric shock the unit. If unsure, contact an electrician or *Risk of fire. electrical Installation company. Do not use during thunderstorms. Pull Do not touch, insert or pull out the 1m out the power plug during storms. power plug with a wet hand. WW 3% Failure to do so may lead to injury Risk of electric shock.
EARNINGS AN SAFETY For cleaning or maintenance of plastic parts, do not use any harsh cleaning agents. (These include, but are not limited to products such as: concentrated sulfuric acid, concentrated nitric acid, glacial acetic acid, carbon tetra chloride, chloroform, acetone, butane, benzene, methyl benzene, phenol, methyl phenol, dimethylformamide, methyl ether, soybean oil, acetate, 40% nitric acid, thick salt acid, 95% alcohol, gasoline, kerosene or brake oil, etc).
EARNINGS AN « Place the battery out of children and infant reach. Xf battery is swallowed, contact a doctor immediately. « If battery fluid leaks onto user, quickly rinse off area using water. SAFETY ® « If battery fluid gets into eyes, immediately rinse with water. Do not rub eyes and seek medical attention. ¥May result in vision impairment or blindness. When battery is in use, do not: * Do not hold or store with metal objects (such as a necklace or a watch). + Do not mix new and old batteries.
INSTALLATION Required Tools Required tools for installation. Please have these tools prepared prior to installation.
BEFORE YOU INSTALL Water pressure check, dimensional drawing. Checking your water supply The lowest working water pressure is 20.3 PSI, the highest water pressure is 108 PSI. If these conditions cannot be met, the bidet may not function as intended; the flush and bidet functions may not work properly. Confirm dimensions of product with installation space Wall Unit: inches 15.66 i T 26.92in n z apg] Side profile Front view Top view BidetMate.
INSTALLING YOUR PRODUCT Install your unit using the Following steps 1 Open the box right side up Remove the accessories first, then remove the unit from the top, as shown In the diagrams below. Smart Toilet Mark your drainage hole with a cross 1. Align the flange with the drain hole, and mark the positions of the four mounting holes of the flange on the ground with a marking pen. NOTE: If your existing toilet flange is still in good condition, you may not need to replace it. 2.
INSTALLATION CONTINUED Install your unit using the Following steps 4 Install the ceramic body, water supply hose and water filter 4, Wrap the T-valve’s threads with Teflon Plumber's Tape, attach the flush water hose to the T-valve, and tighten, 1. Place the wax ring on the drain hole at the bottom of the ceramic. Clean water hose T-valve tp ES Water supply 5. Wrap the T-valve’s threads with Teflon Plumber's Tape, 2.
INSTALLATION CONTINUED 5 Installing the remote 1.Drill two 6mm (1/4 inch) diameter holes on the wall 1.75" (1 3/4 inch) deep. 2. Hammer the anchors into the holes. . 3.Secure the holder with anchors. 4.Use the screws to secure the holder to the wall. 5.Remove the battery cover from the backside of the remote to install batteries 6.0nce finished, remote is ready to be placed in its holder.
INSTALLATION CONTINUED 1. Connact to the grounded outlet. | (1) Check to see if the power light 2.Plug in AC 120V power plug. is on. (2) Once the power light Is on, the taller will run lis Initial diagnostics: lights will tum on, cleaning nozzle will extend, the motor will begin to run and water will run through the system.Once the light is off, the self-diagnostic is complete. (3) Press the side knob to confirm that the toilet is powered on. 1.
FUNCTION EXPLANATIONS Stand by: Press it for 3 seconds to activate it. Activated: under the hip cleaning, female washing, drying mode, press Tt for short time to stop It, press and hold for 3 seconds to shut down. To Flush, not sitting on the seat, press for a short time, Press and hold for another 3 seconds to enter the standby mode, Le ime, Societal Dewey-Tg] Under no cleaning and drying mode, Under no cleaning and drying mode, and seating the toilet. and seating the toilet.
FUNCTION EXPLANATIONS 1 ‘When the seat sensor no longer detracts a user, it will automatically flush The toilet will only flush once. 2 Drying With Flush Press the "Dryer button The warm air function is activated and a flush is performed. Cyclone Dri Tate dries front and rear To Activate: Press “Dryer” once. Press the "Dryer" button again to adjust speed by pressing button 1-3 times for low/mid/high.
MAINTENANCE Regular maintenance is required to ensure optimal performance Directly spraying water onto the 5000 Series body, seat, and lid is prohibited. * Vinegar, "natural" cleaning products, all-purpose cleaners or wipes, and most cleaning products are too harsh for the plastic body of the bidet unit and will damage it. Maintenance of Seat, Lid, and Ceramic Surfaces * Wipe dust or stains with a soft, woven cloth dampened with WATER ONLY.
TROUBLESHOOTING Experiencing issues with your product? If the user should run into any issues, please consult the troubleshooting guide below. If problem persists, please contact a professional. Power button eth Not working Fault Diagnoses Check whether the power cord is fully plugged in or loose. Please check the circuit Check whether the power is switching on or off {the power light is not on} Press the control knob for 3 seconds, the power light is on.
TROUBLESHOOTING Experiencing issues with your product? If the user should run into any issues, please consult the troubleshooting guide below. If problem persists, please contact a professional. Git Ht on The dryer blows cold air Fault graininess Check whether or not the Regulate the temperature of dryer according to dryer switches off the instruction manual. element of dryer is damaged Check whether or not the heating Please contact with our qualified maintenance personnel for repairing.
SPECIFICATIONS Power Rating. 120v~ Frequency 60Hz Ra tad Power Input 1050W (When inlet water temp in 59°F) Seat and Dryer Temperature Range 4 levels Dryer Temperature Range Water Supply Hose Type DNA (G1/27) Water Inlet Minimum pressure 20.
WARRANTY Bidet Mate warrants its Bidets to be Free From defects in materials and workmanship during normal use when properly installed and serviced For a period of: year From the date of purchase For personal use. year From the date of purchase For commercial use. 3 years From the date of purchase For personal users that register their warranty. This limited warranty is extended only to the ORIGINAL PURCHASER of the smart toilet seat and is not transferable to any third party.