Your Berkey® Water Purifier This booklet contains important information. Please do not discard. WARNING: Read all instructions supplied by the manufacturer prior to assembling and using your Berkey water filter. This booklet is a supplemental document only and is not meant to replace the manufacturer’s instructions.
Copyright © 2018 James Enterprise Inc. All rights reserved. No part of this booklet, including the interior and cover design, may be reproduced or transmitted in any form, by any means (electronic, photocopying, recording, or otherwise) without the prior written permission of the publisher.
Table of Contents Assembly Instructions..........................................................................1-5 Black Berkey® Purification Elements Priming Tips........................................................................................... 6 Troubleshooting......................................................................................8 Storing the Elements...............................................................................8 Testing the Elements.............................
Assembly Instructions Diagram 1 3 Berkey Light Model Variation: The Berkey® Light includes the Fabric Lid, Elevated Base (LED Lighted Base is optional), and its own spigot. See the table on page 4 for spigot assembly instructions.
Diagram 2 4 Diagram 3 10. PF-2 Fluoride Element (optional) 1. Lid Knob 11. Lower Chamber 2. Lid 12. Spigot 3. Knob Washer 13. Spigot Washer (beveled)** 4. Knob Screw 14. Spigot Washer (flat)** 5. Upper Chamber 6. Black Berkey® Elements 15. Spigot Hex Nut 16. Rubber Base Ring 7. Element Washer 8. Element Wing Nut 9. Hole Plug* Dotted line indicates assembly direction *Hole plugs are not included with the Travel Berkey, as they are not needed.
***If at any time you experience an issue with your system leaking water, discontinue use, empty the water from both the upper and lower chambers, and contact Customer Service. *** Note: If you intend on storing your Berkey® system for any length of time instead of using it immediately, test the Black® Berkey Elements prior to storing them. See “Storing the Black Berkey® Purification Elements” on page 8 as well as “Testing the Black Berkey® Purification Elements” on page 9 for more information.
F. While holding the hex nut (15) firmly in place, finish tightening by slowly turning the spigot (12) clockwise to the upright position. Spigot Type Outer Washer Inner Washer Standard Spigot (included with Stainless Steel System) Beveled Black - Beveled side toward chamber wall Flat Black Berkey Light Spigot Beveled White - Beveled side toward chamber wall Beveled White - Beveled side toward chamber wall • Follow the printed instructions provided within element box.
To install, place one washer on the threaded hole plug stem. Insert the stem into the upper chamber hole. Place the second washer and then the wing nut onto the hole plug stem below the upper chamber and tighten securely by hand. F. Install the primed PF-2 Fluoride and Arsenic Reduction Elements (optional) (10) by screwing them onto the threaded stems of the purification elements, beneath the element wing nuts (8). Note: Do not turn them more than eight revolutions as this can damage the elements.
Continuous Operation: • Your system will continue to filter water even when the lower chamber is full. This can cause the system to overflow. It is recommended to empty the lower chamber completely prior to refilling the upper chamber. • Purified water can remain in the lower chamber for three days. If any water still remains at the end of three days, dispense into a clean secondary container and refrigerate up to four more days.
2. Press the rubber priming button (tan or black colored) onto the stem of the element. 3. Place the threaded stem of the element between your index and middle fingers and press the priming button against the faucet while placing your thumb on top of the faucet to create a tight seal. 4. While holding the priming button against the faucet, turn on the cold water slowly, allowing water to fill the inside of the element. 5. Allow the exterior wall of the element to sweat beads of water for about 10 seconds.
Troubleshooting - Slow Initial Flow Rate Note: If your Berkey® system also contains the optional PF-2 Fluoride and Arsenic Reduction Elements, the flow rate will typically be reduced by 15 to 20% under normal conditions. 1. To determine if the Black Berkey® Elements have been successfully primed, remove them from the system and submerge them in a tall container of clean water, such as the lower chamber of your Berkey® system. If they sink to the bottom, they are fully saturated.
Testing the Black Berkey® Purification Elements To determine whether the Black Berkey® Elements are working properly, perform the following test using red food coloring. Note: Due to its specific composition, only artificial food coloring that is red in color can be used. Natural dyes that are red in color, such as vegetable juices, cannot be used in place of artifical red food coloring. 1. Confirm that the placement of the element washer and wing nut are correct.
Red Dye Troubleshooting Tips Continued • Are the Washers and Wingnuts installed correctly? The Washer should be on the stem of the black filter inside the upper chamber, and the Wingnut should be secured on the black filter stem in the lower chamber. If not you will not have a proper seal, and will cause your system to fail the test. Please see diagram 2 on page 2 to ensure the washers and wingnuts are correctly installed.
PF-2 Fluoride and Arsenic Reduction Elements Priming Tips 1. With the blue caps in place, wash the exterior of each PF-2 element with water and dish washing soap. 2. With clean hands, remove one blue cap from the end of a PF-2 element. It does not matter which blue cap is removed. 3. While holding the PF-2 element under your sink faucet, slowly turn on the cold water and fill the PF-2 element with water (about ½ cup is needed). Then turn the water off. 4.
Installation Tips 1. Remove the upper chamber of the system and place it upside down so that the threaded stems of the Black Berkey® Elements are facing upwards. 2. With the water flow arrow pointing away from the upper chamber, screw the PF-2 elements onto the stems of each Black Berkey® Element exactly eight full revolutions, and no more. Do not screw the PF-2 elements more than eight revolutions in an attempt to tighten them further as this may damage the internal media screen. 3.
Storing the PF-2 Elements • UNUSED: The PF-2 elements can be stored indefinitely in their original packaging. Do not store with fragrant items. • USED: Place the PF-2 elements in a re-sealable zipper storage bag and store them in the refrigerator for up to two weeks. Note: o Do not store used PF-2 elements for longer than two weeks. o Do not store the PF-2 elements in the freezer. o Remember to re-prime the PF-2 elements before using them again.
also be cleaned in the dishwasher but remove all parts and attachments first. If you have a Berkey® Light system, do not place any of its components in the dishwasher. Note: If your Berkey® system is filtering hard water, which is water with a high dissolved mineral content, scale from naturally-occurring minerals such as calcium may develop in the spigot and chambers after prolonged use.
Why is there a Residue in the Chambers and Cookware? • Naturally-occurring minerals such as calcium and magnesium carbonates, bicarbonates, chlorides, and sulfates can leave deposits in the Berkey® chambers as well as cookware that have contained the filtered water. These deposits can be removed by thoroughly cleaning the chambers and cookware. For cleaning instructions, see “Cleaning the Chambers of the Berkey® System” found on page 13. If filtering hard water see the note section on page 14, as well.
Packages received without a RMA # will be charged a 20% handling fee. Return instructions can be found in the "Returning your Berkey® Water Filter System" section on page 19. Exchanges For exchanges please follow the instructions in the above section. If the returning item is valued at $55 or more, we will cover the return shipping cost to us. Outbound shipments for new items will ship free if the value meets or exceeds $45*.
Warranty - Continued Berkey Care Lifetime Warranty For our customers who chose to register at the time of purchase, we offer a lifetime warranty on select Berkey® Systems. The Berkey Care Lifetime Warranty covers the; Travel Berkey®, Big Berkey®, Royal Berkey®, Imperial Berkey®, and Crown Berkey®.
Manufacturer’s General Warranty - Continued This warranty will not apply to units which have been used for purposes not intended, which have been altered so as, in the manufacturers judgment, to adversely affect its performance. This warranty is for the original retail purchaser only, and cannot be transferred. The laws of the state of Texas, USA will govern any disputes regarding this warranty or claim made.
Returning Your Berkey® Water Filter System Please follow the disassembly and packing instructions carefully. Fees may apply if the product is not returned in its entirety with original packaging, or if it is damaged during return shipment. The following information is comprehensive, and all sections may not apply to your specific return. Disassembly (Please refer to the Assembly Diagram on page 1) Step 1 –Disassemble the Lid A. Unscrew the knob (1) from the lid (2). B.
B. Remove the hex nut (15) and the spigot from the inside of the lower chamber (11) and screw the hex nut back onto the spigot (12) with the washers (13, 14) attached. C. Leave the rubber base ring (16) attached to the bottom of the lower chamber (11). D. Set all pieces aside. Step 4 – Packing the System for Return Shipping Failure to properly pack your system for return shipping could result in a restocking handling fee of up to 20% if the unit is received damaged. A.
Parts and Accessories *Prices are subject to change without notice. * Black Berkey® Replacement Elements (Set of 2) $107.00 Set of 2 Wing Nuts with Washers $4.00 Black Berkey Primer™ $25.00 PF-2 Fluoride and Arsenic Reduction Elements $50.00 For Black Berkey® Elements Require Black Filters Optional Hole Plug $1.25 Stainless Steel Stand Elevates stainless steel system six inches. Rubberized feet for extra stability. Four sizes to fit all stainless steel systems.
*Prices are subject to change without notice. * Replacement Spigot for Stainless Steel Systems $10.00 Berkey Light® Replacement Spigot $10.00 Fits all stainless steel systems Fits Berkey Light® Systems only Stainless Steel Spigot Fits all stainless steel systems $20.00 Water View Spigot Spigot with glass sight tube. Fits all stainless steel systems. Sizes vary based on system model. $40 - $45 Berkey® Shower Filter $63.00 Shower Filter Replacement $46.
*Prices are subject to change without notice. * Sport Berkey® Water Bottle $34.95 Sport Berkey® Water Bottle Replacement Filter $19.95 Thinksport Stainless Steel Water Bottle Available in 350mL, 500mL, & 750mL. $15 - $19 Berkey® Maintenance Kit Includes 2 scrubbing pads, 1 spigot, 2 wing nuts and washers, 1 priming button, 2 hole plugs, 1 knob, red food dye, and instruction booklet. Fits Stainless Steel Units.
*Prices are subject to change without notice. * Boroux Glass Bottle $58.99 Boroux Starter Kit $73.99 Boroux Storage Rack $39.99 Boroux Insulated Glass Bottle Sleeve $29.99 Boroux Can Jacket $9.
For further assistance please contact Customer Service: • • • • 1-800-350-4170 customerservice@berkeyfilters.com Live Chat on www.berkeyfilters.com Please provide the order/invoice number for prompt service. Customer Service hours: Monday through Friday - 7:00AM to 5:00PM (MST) Saturday - 8:30AM to 5:00PM (MST) Additional information about the Berkey Water Purifiers is also available online at http://www.berkeyfilters.com. My Order/Invoice Number: Information accurate at time of publication.
