BENDIX COMPRESSORS AND PARTS REMANUFACTURED EXCHANGE COMPRESSORS Model Bendix Piece No. Serial No. Country of Manufacture TUFLO501COMPRESSOR PC NO. SER. NO. REMFG. BY BENDIX IN U.S.A. Tu-Flo® 550 & Tu-Flo® 750 Compressor most popular configurations Port Right Unless indicated, inlet and Orientation discharge locations are as shown. Tu-Flo® 550 for CAT Part No. 5002984x 3406, C10, C12, C15, C16 (rear end cover studs) Part No. 5005790X 3176, C15, C16 Tu-Flo® 750 for CAT Part No.
BENDIX COMPRESSORS AND PARTS WHY A BENDIX REMANUFACTURED COMPRESSOR? •All components are inspected and then replaced or remanufactured to the highest Bendix OEM manufacturing and product specifications, long the industry standard. •All Bendix remanufactured compressors meet or exceed OE manufacturing functional, end-of-line test specifications.
HALDEX COMPRESSORS AND PARTS REMANUFACTURED HALDEX COMPRESSORS Head Assembly Cylinder Block Rotate to match your inlet/outlet port needs; extra gasket included! Water cooled to provide maximum life and performance. Piston & Ring Assembly Unloader Assembly Thru-the-head servicing. Quick and easy way to restore to original performance! Perfect balance of function and service life. Minimizes oil passing and life ending early failures due to piston and cylinder wear.
BENDIX AIR DRYERS Governor Compressor Reservoir #1 The primary duty of the air dryer is to eliminate the moisture and dirt that would cause damage to valves and other system components. The air dryer removes these pollutants, providing dry air, free of contaminants that can cause premature failure of the air and brake system.
BENDIX AD-9™ AIR DRYER Part No. 107794X Desiccant Cartridge Kit Part No. 5004341X AD9 12V Purge Valve Kit AD-9 Air Dryer Parts Kit List Key Description New Purge Valve w/ heater 800405 -12v 109570 -24v Reman Purge New Purge DLU Heater-note 1 Valve w/ heater Valve w/ heater Des. Cart kit Purge Vlv & Therm kit 5004341X -12v 109580 -12v 107796 -new Maint.
BENDIX AIR DRYERS BENDIX REPAIR KITS AD-2 - Desiccant type Reman. 12 volt, for AD-2 AIR DRYER 1/2" port. 102657N Thermostat Kit Includes Thermostat, Part No. 286934RX gasket and "O" ring. 287053N Purge Valve Replacement Kit Includes purge valve, diaphragm, boot and "O" rings 101900X Desiccant cartridge 286875RX End cover assy. -12v. 286876RX End cover assy.-24v.
HALDEX AIR DRYERS & REPLACEMENT PARTS •MTC Multi-Treatment Cartridge• Part No. 47178964(DRYest™) Part No. DQ6050 (PURest™) 5 stages - inreases dryer life! 1-Dust filter 2-Small dessicant 3-Medium dessicant 4-Large desiccant 5-Aluminum mesh •DRYest™ System Purge Dryer• Part No. DA35100 new outright Uses MTC dessicant cartridge for superior drying (Part No. 47178964), compact size, built in heater. •PURestTM Air Dryer• Part No.
FLEETCRAFT AIR DRYER AND PARTS Fleetcraft Air Dryer With integral turbo cut-off valve, no need for purge tank. Includes mounting bracket. Part No. FC955205 Fleetcraft Desiccant Cartridge Kit For Turbo-2000 & HD-2000 Air Dryer Part No. FCT224 Air Dryer Cartridge Part No. FC950011 ISOLATION VALVE - ALCOHOL EVAPORATOR - GOVERNORS ISOLATION VALVE (Turbo Cut-Off Valve) Used with air dryers not equipped with this feature. Allows use of air dryer on turbo charged engines without affecting engine performance.
PRESSURE PROTECTION VALVES PRESSURE PROTECTION VALVE Used to protect air brake system from accessory failure. Nonadjustable. 1 /4" NPTF inlet port, 1 /4" NPTF outlet port. Operating PSI Part No. Open Closed KN31000 65 45 KN31010 95 75 PRESSURE PROTECTION VALVE with one way check valve Used to protect air brake system from accessory failure. Nonadjustable. 3/8" NPTF inlet port, 1/2" NPTF outlet port. Opening Part No. Pressure KN31170 50 PSI KN31171 75 PSI Tractor Protection Valve TP-3DC Part No.
CHECK VALVES C A B SINGLE CHECK VALVE SC-2 Steel Seat Part No. A B C 800372 1/2" PT 1/2" PT 2.92" 800373 3/8" PT 3/8" PT 25/32" SINGLE CHECK VALVE SC-1 Steel Seat Part No. A B C 800375 1/4" PT 1/4" PT 23/32" C The 800372 single check valve is A also available in Fleetcraft: Part No. FC800372 B DS-2™ DOUBLE CHECK VALVE with STOP LIGHT SWITCH Part No. 286452N Ports 3/8" "B" Hole 227/32" 227/32" DC-4 DOUBLE CHECK VALVE 3 /8" NPTF All Ports: 11 "B" Hole: /32" Dia. Part No.
QUICK RELEASE VALVES Aluminum Die Cast Body Supply/Delivery Differential 0 PSI (B) (C) Inlet Delivery Differential Part No. Port Ports PSI 3 KN32050 1/2" /8" 6 3 KN32060 3/8" /8" 6 QRN - Lightweight, nonmetallic. Mounting holes 11/32" diameter on 11/2" centers. QUICK RELEASE VALVES Used wherever a quick release function is required in the air brake system. Aids in meeting FMVSS 121 timing requirements. Part No. QRN-2 Inlet Delivery Differential Part No.
CONTROL VALVES MV-3 CONTROL MODULE Auxiliary An integrated control assembly Port for control panel mounting in tractor. It provides all the federal legal Mounting Plate requirements for trailer air supply and parking brake control and permits the tractor parking brakes to be applied while air is supplied to the trailer. Six 1/4" ports. Nonmetallic.Designed to supersede the MV-2 valve. Different mounting separates styles. Part No. 800257 - Fig. 1, .27 Push in fittings. Part No. 800516 - Fig. 1, .
PUSH PULL VALVES PUSH PULL CONTROL VALVE PP-5 (w/pilot air release) A pressure sensitive on-off control commonly used with vehicle torque converter system, engine speed control, and some parking brake systems. Automatic release pressure 40 PSI. 1 /8" supply, 1/8" delivery and exhaust, all NPTF. Part No. 281946N PUSH-PULL STYLE VALVE Controls parking /emergency brakes. Pop pressure: 35±10 PSI. 7 /8" mounting hole required. Knob included. Delivery Made of Engineering Grade Composite. All ports 1/8" NPTF.
LEVER STYLE VALVES / TRAILER BRAKE CONTROL VALVES DOUBLE FLIPPER STYLE VALVES Panel mount, directional air control valve. May be used for control of push-pull air cylinders or various other air operated devices. Supply ports 1/4" NPTF Delivery Ports (2) 1/8" NPTF PART NO. KN20080 APPLY/RELEASE POSITIONS 3 position with manual release only. FLIPPER STYLE VALVE Panel mount. Exhaust On-off nonautomatic two position valve. Made of Engineering Delivery Grade Composite. Delivery All Ports 1/8".
SPRING BRAKE CONTROL VALVES SR-5 TRAILER 1 /4" Service/ SPRING BRAKE VALVE Spring Brake Reservoir Die-cast aluminum, reservoir mounted valve that controls up to four spring brake actuators (A) during parking or emergency applications.Trailer Service All threads NPTF. 3 /8" Delivery (4) Anti-Compounding: Part No. 065437 Part No. OR109615X MULTIFUNCTION RT-4 SPRING BRAKE VALVES Meets all FMVSS-121 trailer requirements for spring brake control and other regulations.
RELAY VALVES - BENDIX R-12™ RELAY VALVE Part No. 102802N Piston operated, with 4 delivery ports for service or parking brakes. Crack pressure: 4 PSI unless noted. Maintenance Kit for R-12 & R-14 Valves. KIT INCLUDES: (A) Key 1 2 3 4 5 6 7 8 9 10 11 Part No. 065104 3 /8" Vertical Delivery Ports 1 /2" Supply Ports 1 /4" Service Port Part No. 102626N Service (A) Supply 1 /2" Vertical Delivery Parts 1 /2" Supply Ports 1 /4" Service Port (B) Delivery Part No.
RELAY VALVES - BENDIX CORELESS VALVES Bendix Coreless® Valves - Outright Reman Program. The Coreless® valves program gives you virtually 100% coverage of the Bendix remanufactured valve line. Forget about carrying remanufactured valves with core obligation as part of your regular inventory. With expanded product coverage, it has never been easier to make the jump to Coreless.
RELAY VALVES - SEALCO 2 PORT SERVICE RELAY Used primarily for single axle trailer service brakes, or axle by axle trailer brake designs. Nipple mounted. Crack Pressure 4 PSI. 3 Control Port: /8" NPTF Reservoir Port: 1/2" NPTF Delivery Ports: 3/8" NPTF Part No. 110410 2 PORT SERVICE RELAY VALVE LOV-2 3 Control Port : /8" NPTF 1 Reservoir Port: /2 " NPTF 3 Delivery Ports (2): /8" NPTF Cracking Pressure 1.5 PSI Part No.
RELAY VALVES - HALDEX RELAY VALVES(RG2) 2 Delivery Ports. Compact size. A fast, low cracking pressure straight relay for tractor-trailer-truck applications. Crack pressures 5.6 +/- 1.0 PSI. Cover may be rotated without affecting warranty. EMERGENCY RELAY VALVE 4 port. Suitable for pre-121 trailers, converter dollies, or exempt trailers. Crack pressure 3.0 PSI (1)=Plugged * = non-charging SERVICE EMERG. PART NO.
BRAKE (FOOT) VALVES DUAL BRAKE VALVE The E-6 dual brake valve is a floor mounted treadle or lever operated valve with two separate supply and delivery circuits for service and secondary braking, providing graduated control for applying and releasing vehicle brakes. Part No. 286171N Part No. 238888N Folcrum Pin Part No. 236979N Mounting Plate Shown with valve. Valve not included. E8P BRAKE VALVE Lower Body Rotated 90° Part No. 800629 (Replaces E-12 065313 AND 800583) Part No.
SHUT OFF VALVES / DRAIN VALVES SHUT OFF VALVE Ball type valve with 1/2" NPTF both ends. Working pressure 150 PSI. Part No. 12116 EXTERNAL SEAT DRAIN COCK NPTF 1 /8" 1 /4" 3 /8" 1 /2" DRAIN VALVES WITH CABLE Use on wet or dry tanks. 1/4" NPTF. Nylon coated stainless cable. DRAIN VALVES WITH CABLE Use on wet or dry tanks. 1/4" NPTF. Brass body with stainless spring. Nylon coated stainless cable. 4' Cable Part No. FC12104 5' Cable Part No. FC12105 DRAIN COCK NPTF Part No.
FLEETCRAFT VALVES Valves Valves New outright, one year warranty. New outright, one year warranty. Part No. FC28500 Part No. FC28510 Part No. FC28520 Relay Valve Straight relay. 3/8" delivery, 3/8" reservoir. Crack pressure 6 psi. Relay Valve Straight relay. 3/8" delivery, 1/2" reservoir. Crack pressure 6 psi. Relay Valve Straight relay. 1/2" delivery, 1/2" reservoir. Crack pressure 6 psi. Part No. FC065104 Relay Valve 3/8" vertical delivery ports (4) 1/2" supply. 1/4" service port.
VELVAC AIR VALVES Four-Way Push/Pull Valves Part No. 320121 - Two Position Valve Part No. 320122 - Three Position, Holding Type Valve Four-Way Electronic Solenoid Valve Part No. 320131 • Features newly designed orifice area increasing airflow • Manual override switch for manual operation • (3) 9/32" dia. valve body mounting holes, (5) 1/4"-18 FPT ports • Exhaust cone filters included (030084 = 1/8" & 030092 = 1/4") Four-Way Rotary Handle Valve Part No.
ABS TECH INFO - ARVIN MERITOR End of Line Testing without TOOLBOX™Software ( Using the ABS lamp to check the line.) 1. Apply 12 volts DC power to the ABS. 2. The ECU/single modulator valve assembly should click two times. 3. If the indicator lamp comes on for three seconds and goes out: This indicates a correct installation. The end of line test is complete. If the ABS indicator lamp comes on and stays on, check the sensor installation: A.
OEM ONLY - ABS 2S/1M, 2S/2M MERITOR WABCO COMPONENT KITS 2 Sensor/1 Modulator Valve (2S/1M) Configuration Shown Tandem Suspension, Two Wheels Sensed 2 Sensor/1 Modulator Valve (2S/1M) Configuration Shown Tandem Suspension, Two Wheels Sensed KIT PART NO. 1542014 KIT PART NO. 1542015 REPLACEMENT PARTS LIST REPLACEMENT PARTS LIST FOR Qty 1 1 2 1 1 Part No.
ABS - 2S/1M COMPONENT PARTS - SPRING BRAKE PRIORITY A/C = Anti-Compounding Service Brake Spring Brake Supply Line (Red) Control Line (Blue) COMPONENTS LISTING: Typical Set Up Guide: No. 1 = 110500 - Spring Brake control valve, No. 2 =S4005001010 - Wabco ECU valve, No. 4 = 6003 - 3/4" to 1/2" pipe nipple, No. 5 = 6006 - 3/4" pipe nipple, No. 6 = N9508-AA air tank, No. 7 = 1010447 - spring brake chamber, No. 8 = 1011451 - red emergency gladhand, No. 8 = 1011452 blue service gladhand.
ABS - 4S/2M MERITOR WABCO COMPONENT KITS 4 Sensor/2 Modulator Valve (4S/2M) Configuration Shown Suggested Electrical Diagram Tandem Suspension, Four Wheels Sensed We have developed these kits for MANUFACTURERS ONLY - OEM ONLY. These kits are not available to aftermarket distributors - Those kits are on the following pages. THANK YOU! SPRING BRAKE CONTROL VALVE Spring Brake Priority System Complies with all changes to FMVSS121.
MERITOR WABCO ABS ENHANCED EASYSTOP™ CONVERSION KITS Meritor WABCO has created a series of retrofit kits to replace the previous Easy-Stop platform, to the current production Enhanced Easy-Stop platform. Easy Stop was installed on production built trailers between March 1997 and February 2001. Enhanced Easy-Stop incorporated current technology to address regulatory PLC requirements and has been installed from March 2001 to present.
MERITOR WABCO ENHANCED EASYSTOP™ COMPONENTS Part No. S4005001010 ECU Valve Assembly 2S/1M Basic for trailer (after the 3/1/01 date) Part No. S8946073120 Adapter cable. Connects Easystop power cable to enhanced Easystop ECU/Valve assembly. Part No. S4461082010 ECU Only Part No. S4005001020 ECU Valve Assembly 2S/2M Basic for trailer (after the 3/1/01 date) Part No. S8946073130 Adapter cable with diagnostic cable. Connects Easystop power cable to enhanced Easystop ECU/Valve assembly. Part No.
MBS ABS KIT - FLEETCRAFT Wabash National announced that it has discontinued its proprietary ABS products for all production trailers, and we have the complete replacement retrofit kits available for slider suspensions.
MISCELLANEOUS MERITOR WABCO ABS COMPONENTS Sensor Placement When more than one wheel is controlled by a single valve, sensors should be mounted at the axle which tends to lock first. For spring suspensions this is usually the forward axle. For air suspensions this is usually the rear most axle. 1810000 1810002 1810003 1810001 Right Angle (90°) Sensor Kits Includes sensor, bushing clip, friction lube, and instructions. Part No. Cable lead in Feet R955335 1.0 R955336 3.0 R955341 5.8 R955342 6.
ABS ELECTRIC CONFIGURATION - 2S/1M - HALDEX PLC - FULL FUNCTION Kit Part No. AQ961404 PARTS LIST Consisting of: Qty Part No. Description 1 AL919310 ECU 1 AL430624 Full Function ABS Valve 2 AL919804 7.5' Sensor Cable Ext 1 AL919901 12' Power Cord Ext 1 box Tie Down Clips Kit Part No. AQ960802 PARTS LIST Consisting of: Qty Part No. Description 1 AL919310 ECU 1 AL430624 Full Function ABS Valve 2 AL919804 7.5' Sensor Cable Ext 1 AL918602 62' Power Cord, 38' drop 1 box Tie Down Clips ECU Part No.
ABS PLC SELECT UPGRADE KIT - 2S / 1M ECU Valve PLC Select Part No. AL919338 Wheel-speed Sensor and Trailer Power connects directly to ECU - no intermediate cables required. Single fastener design assures easy serviceability. Potted ECU Enclosure provides excellent protection from the environment. Part No.AQ964110 KIT CONTAINS: 1M Power Cord Extension 0.5M Sensor Extensions PLC Select ECU & Bracket. •Meets FMVSS121 requirements including March 2001 In-Cab Malfunction Lamp.
HALDEX ABS COMPONENTS ABS Power Cable With integral spring brake control. ECU end includes industry Pre-installed reservoir nipple with standard 5-pin female swivel and locknut feature. connector. Comes standard with filters in 7-way end is stripped wires. both the control and supply ports. For production Mar. '01-present. Part No. Description Part No. Length AL430611 4 port, 1/2" nipple, AL918603 38 feet 12 volt, 3/8" ports. ABS lamp lead is 25 feet. ABS Modular Valve less ECU FFABS Valve Part No.
BENDIX ABS COMPONENTS ® Bendix TABS-6 (Standard) Trailer Antilock Braking System Few connections, small and light, fast and reliable, for all applications. Part No.801855 2S/1M trailer ABS module. Communicates over PLC. Has a 4 port relay. MC-12 Trailer ABS Modules Replacement Kit Part No.802902 Bendix EC-30™ Electronic Controller -ECU Part No. 801236 6S/4M -sensors and modulators. Traction control. EC-16™ and EC-17™ service replacement. Bendix MC-30™ trailer ABS module Part No.800737 Tank mounting.
