Installation Guide

ManualsBrandsBelvedere ManualsBathAlpha Wall-Mount Bathroom Sink with Fixtures and 403 Vacuum Breaker in Black

Shampoo

Bowls

3100 CAMEO BOWL

3800 ALPHA BOWL

Belvedere USA Corporation

A wholly owned subsidiary of The Wella Corporation

One Belvedere Boulevard, Belvidere, Illinois 61008

Printed in U.S.A. E.C.O. 4164 4001021 Rev. 1-03

PORCELAIN ENAMEL SHAMPOO

BOWL WITH VACUUM BREAKER

AND MODEL 522 FIXTURE

INSTALLATION AND PLUMBING

NOTE: Read the instructions through before starting

to familiarize yourself with the components.

Any conformance with LOCAL CODES or

INSPECTIONS is the RESPONSIBILITY

OF THE PURCHASER.

1. Attach the Fixture to the Bowl according to

the instructions packed with the Fixture.

ATTACH HOSE RECEIVER TO BOWL

(STEPS 2 thru 6).

2. To make Hose Receiver installation easier,

complete these steps to cut screw threads

in the mounting holes:

S Take a Mounting Screw and drive it 2 or

3 turns into one hole.

DO NOT OVERTIGHTEN.

S Remove the Screw.

S Repeat for all four (4) mounting holes.

If the Bowl is not equipped with a Vacuum

Breaker, proceed to Step 4.

*NOTE: If you ordered a Vacuum Breaker,

your Hose Receiver will have two

holes for mounting the Vacuum

Breaker.

4. Place the Gasket

over the flange

on the bottom of

the Hose Receiver.

PAGE 1 of 4

3100

3800

VACUUM

BREAKER

MOUNTING

HOLES

DRIVE

SCREW

IN 2 OR 3

TURNS

MOUNTING

SCREW

3. Place the Vacuum

Breaker pipes

through the

Gaskets and the

holes in the

Hose Receiver as

shown.

Secure the Vacuum

Breaker to the Hose

Receiver with

two Nuts.

DO NOT

OVERTIGHTEN.

NOTE: Install the Vacuum

Breaker as shown.

If the Vacuum Breaker is

installed backwards,

it will interfere with the

Spray.

VACUUM

BREAKER

HOSE

RECEIVER

GASKET

NUTS

VACUUM

BREAKER

HOSE

RECEIVER

GASKET

Summary of content (4 pages)

PAGE 1
Shampoo Bowls 3100 CAMEO BOWL 3800 ALPHA BOWL PORCELAIN ENAMEL SHAMPOO BOWL WITH VACUUM BREAKER AND MODEL 522 FIXTURE INSTALLATION AND PLUMBING NOTE: Read the instructions through before starting to familiarize yourself with the components. Any conformance with LOCAL CODES or INSPECTIONS is the RESPONSIBILITY OF THE PURCHASER. 3100 1. Attach the Fixture to the Bowl according to the instructions packed with the Fixture. ATTACH HOSE RECEIVER TO BOWL (STEPS 2 thru 6). 2.
PAGE 2
5. Place the Hose Receiver in the Bowl with the large hole in the dome facing the front of the Bowl. Install the Mounting Bracket on the bottom side of the Bowl with four (4) embossed DOME corners facing upward, against the bottom of the Bowl. Secure with EMBOSSED four (4) CORNER (UP) Screws. DO NOT OVERTIGHTEN. MOUNTING SCREW 6. If your Bowl is not equipped with a Vacuum Breaker attach the Spray Hose connector to the fixture tailpiece. INSTALL THE DRAIN ASSEMBLY (STEPS 7-10) PLUMBER’S 7.
PAGE 3
12. Mount the Bowl onto the Wall Bracket by lowering the Lugs on the back of the Bowl into the Wall Bracket. TO MOUNT THE 3100 and 3800 BOWLS TO THE WALL (STEPS 11 THRU 13) 11. Install the Wall Bracket so that the top edge is 31-1/4” from the finished floor. (This backet height is suggested to obtain the most suitable neckrest height. However, the bracket height may be varied to suit personal preference.) Be sure that the Bracket is securely fastened to a structural member in the wall.
PAGE 4
ROUGH-IN PLUMBING SPECIFICATIONS. This Shampoo Bowl is designed for optimum comfort when the Bowl Neckrest is at 31”. However, this may vary to suit individual salon owners. SEE NOTE BELOW. Belvedere Recommends a Bowl Neckrest height of 31”. To mount the Bowl at this height, locate the bracket height as shown in these specifications.