Warranty

Belldinni’s responsibility for the merchandise is limited to the regulations of the present
Manufacturer’s Warranty.
All Belldinni doors are manufactured to the highest-quality craftsmanship standards and are backed by a limited 2-year warranty
against defects in workmanship and materials. The 2-year period starts from the date of delivery of goods to the customer.
WHAT THIS LIMITED WARRANTY DOES NOT COVER
This Limited Warranty does not include non-conformities or damages attributable to or arising from:
 General wear an
d tear.
 Any
Product that is over three-feet (3′) in width and/or eight-feet (8′) in height.
 The finish on a locking system (door handles and lockset) and hinges is not warranted and is purchased “AS IS”. This
includes but is not limited to finish discoloration, tarnishing, scratches, abrasions, and visual imperfections. Exposure to
certain environmental conditions, including but not limited to salt spray, acid rain, high humidity, or other corrosive
elements may adversely affect the coatings on finishes (as well as the mechanical and multi-point locking system
(door
h
andles and lockset mechanisms). Timely and proper cleaning of hinges and a multi-point locking system will help to
extend the finish appearance (and mechanical mechanisms) and discourage the possibility of rust and corrosion. Hing
es
and a l
ocking system (door handles and lockset) should be wiped down periodically with a soft, water-dampened cloth and
dried off with a soft dry cloth. Abrasive cleaners or other harsh chemicals should never be used on hinges or a lockin
g
syste
m (door handles and lockset). Maintenance of the finish (and mechanical mechanisms) is the responsibility of th
e
Warranty Hol
d
er.
 Th
e mechanism on hinges installed within 5 miles of a body of salt
water.
 Th
e mechanism on the locking system if the Product is installed within 5 miles of a body of salt water or installed on any
steel products. Belldinni does not recommend the use of locking systems with steel products. If any locking system is used
with steel products, it’s used “AS IS” WITH NO WARRANTIES.
 EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY RELEVANT TO ITS SUITABLITY FOR
ANY
PARTIC
ULAR PURPOSE OR USE.
 Failure by the Warranty Holder or its agents to observe one or more of the following rules of Product handling will void
this Warrant
y:
- A
void direct contact with water, fire, sunlight exposure;
- Avoid rough handling of doors and door un
its;
- Al
l doors must be transported in containers, on pallets or other devices, protecting them from damage, moisture
,
preci
pitation or sunlight exposure;
- The door assembly in newly built or repaired premises is allowed only after the building materials have dried out
completely;
- Prior to the installation, doors and door units must be kept at the place of installation 3-4 days before they achieve optimu
m
hum
idity and temperature paramete
rs;
- Doo
r unit installation should be carried out by trained and properly qualified specialists;
- Prefinished door units should be installed after the floor, ceiling and wall priming and painting is over, in orde
r
t
o secure the door finishes from getting stained and/or dirty;
- Only detergents (not water!) suitable for corresponding surfaces (veneer, enamel, polypropylene) and containing no
abrasives and solvents can be used for cleaning a door un
it;
-
Aerosols for wooden furniture may be applied on a door unit to give the surface additional shine and freshn
ess (with
refe
rence to the recommendations on the use of aerosols);
- It is forbidden to knock on the door glass with objects that may cause the glass shattering;
 Misapplication of Products or faulty building design or construction, including inadequate flashings, caulking, building
settlement, or structural failures of walls or foundations, or inadequate overhang
s;
 Installation in
locations or a manner that exceeds or deviates from Product design standards and/or testing and certifie
d
perform
ance specifications, and/or not in compliance with building codes;
 Product failure due to improper installatio
n.
 Produ
ct reinstalled after removal from its original installation, except in connection with proper and timely maintenance of
components which incur normal wear and tear;
 Rotting, splitting, warping, swelling, or other adverse condition, of or attributed to or arising from a frame system, un
less
th
e frame system is a genuine Belldinni component part. Use of a non-Belldinni frame system by the Warranty Holder (or