TDS

ManualsBrandsBEHR PRO ManualsPaint5 gal. e600 White Satin Enamel Exterior Paint

TECHNICAL DATA SHEET

This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other nature

are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional, call 1-800-854-0133

Revised 3/1/2016

1 of 2

e600 EXTERIOR SATIN PAINT

NO. PR640 WHITE BASE

PRODUCT INFORMATION

BEHR PRO™ e600 Exterior Satin Paint is specically designed to meet the demanding expectations of professional painters.

Developed for optimal sprayability, this 100% acrylic formula provides excellent hiding power and a highly uniform,

mildew resistant nish. BEHR PRO Exterior Satin Paint is a durable, washable nish for exterior walls and trim. Not for use

on glossy surfaces or oors.

RECOMMENDED USES:

Ideal for both commercial and residential properties over properly prepared:

• Concrete, Concrete Tilt-up • Concrete Block/CMU • Cement Board Siding • Brick

• Stucco • Wood • Plywood • Ferrous Metals

• Non-Ferrous Metals • Vinyl Siding

PRODUCT SPECIFICATIONS:

Tint Bases/Max Tint Load:

No. 640 124 oz. / 6 oz.

No. 644 117 oz. / 13 oz.

No. 643 116 oz. / 14 oz.

Gloss: 10-20 @ 60°

Sheen: 20-30 @ 85°

Resin Type: 100% Acrylic

Weight per Gallon: 10.09 lbs.

% Solids by Volume: 32%

% Solids by Weight: 42%

VOC: <50 g/L

Flash Point: N/A

Viscosity: 95-105 KU

Recommended Film Thickness:

Wet: 6.4 mils; Dry: 2.17 mils @ 250 Sq. Ft./Gal.

Wet: 4.0 mils; Dry: 1.36 mils @ 400 Sq. Ft./Gal.

Coverage: 250-400 Sq. Ft./Gal., depending on the surface

texture, porosity and application method. Does not include

the loss of material from spraying. Film thickness depends

on porosity and various substrate irregularities.

APPLICATION:

Brush: Nylon/polyester

Roller:

Smooth Surfaces: 3/8"-1/2" nap

Porous Surfaces: 1/2"-3/4" nap

Airless Spray: Fluid pressure of 1,500 - 2,200 psi

Tip: .015"- .021"

Filter: 60 mesh

Thinning: Not recommended. Product is formulated for use

at package consistency only.

Dry Time: 77°F (25°C), 50% RH:

Longer dry time may be required in cooler temperatures

and higher humidity.

To Touch: 2 hours

To Recoat: 4 hours

Full Cure: 14 days

SURFACE PREPARATION:

• All surfaces must be clean, free of dust, chalk, oil, grease,

mold and mildew stains, loose and peeling paint, rust and

all other foreign substances.

• Glossy surfaces must be ‘scu sanded’ with an appropriate

sandpaper and primed prior to coating.

• Allow new stucco, plaster and masonry to cure for

30 days before painting.

WARNING! If you scrape, sand or remove old paint,

you may release lead dust. LEAD IS TOXIC. Contact the

National Lead Information Center at 1-800-424-LEAD or

visit www.epa.gov/lead.

RECOMMENDED PRIMER/SYSTEMS:

PROPERLY PREPARED NEW SURFACES:

Wood: Composition Panels/Siding, Fiber Board

• BEHR PREMIUM PLUS® Interior/Exterior Multi-Surface

Primer & Sealer No. 436

Wood: Cedar, Redwood, Shakes & Shingles