TDS

ManualsBrandsBEHR PRO ManualsPaint5 gal. i300 White Semi-Gloss Interior Paint

TECHNICAL DATA SHEET

This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other

nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,

Revised 2/2018

PRODUCT INFORMATION

BEHR PRO™ Interior Semi-Gloss Paint is a professional quality latex paint with superior hide and coverage, excellent

sprayability, spray back-roll and superior touch-up. This product contains an antimicrobial agent to protect the surface

of the paint film from mold and mildew.*

RECOMMENDED USES:

Use on properly prepared primer or previously painted surfaces. Ideal for family rooms, living rooms, dining rooms,

bedrooms and ceilings.

• Concrete • Plaster • Plywood • Architectural Plastics

• Concrete Block/CMU • Drywall/Gypsum Board • Ferrous Metals

• Brick • Wood • Non-Ferrous Metals

PRODUCT SPECIFICATIONS:

Tint Bases/Max Tint Load:

PR370 124 oz. /6 oz.

PR374 117 oz. /13 oz.

PR373 116 oz. /14 oz.

Gloss: 35-45 @ 60°

Resin Type: VAE/Acrylic Blend

Weight per Gallon: 10.6 lbs.

% Solids by Volume: 37 ± 2%

% Solids by Weight: 49 ± 2%

VOC: <5g/L

Flash Point: N/A

Viscosity: 90 - 100 KU

Recommended Film Thickness:

Wet: 5.3 mils; Dry: 1.9 mils @ 300 Sq. Ft./Gal.

Wet: 4.0 mils; Dry: 1.45 mils @ 400 Sq. Ft./Gal.

Coverage: 300 – 400 Sq. Ft./Gal. depending on the surface

texture, porosity and application method. Does not include

the loss of material from spraying. Film thickness depends

on porosity and various substrate irregularities.

APPLICATION:

Brush: Nylon / Polyester Blend

Roller:

Smooth Surfaces: 3/8" - 1/2" nap

Rough Surfaces: 1/2" - 3/4" nap

Airless Spray: Fluid pressure of 1,500 - 2,200 psi

Tip: .015" - .021"

Filter: 60 mesh

Thinning: Not recommended. Product is formulated for use

at package consistency only.

Dry Time: 77°F (25°C), 50% RH:

Longer dry time required in cooler temperatures and in

higher humidity.

To Touch: 1 hour

To Recoat: 2 hours

Full Cure: 2 weeks

SURFACE PREPARATION:

All surfaces must be clean, free of dust, chalk, oil, grease,

wax, polish, mold and mildew stains, loose and peeling

paint, rust and all other foreign substances.

New Drywall: All drywall surfaces should be suciently

sanded smooth. Remove any remaining drywall dust prior

to priming. Allow all drywall compounds to be completely

dry prior to coating. Previously Painted Drywall: Remove

all loose and peeling paint and all other foreign substances.

Clean any dirt and grease by scrubbing the surface with

a detergent and water solution, followed by a thorough

rinsing with clean water. Set nails and ll holes, scratches,

and gouges with the appropriate spackling material. Let dry

completely and sand smooth. Remove all dust with a wiping

cloth. Fill all gaps with a 100% acrylic, siliconized, paintable

caulking, and allow to completely dry prior to coating.

Glossy Surfaces: For maximum adhesion, sand the surface

thoroughly before coating.

New Wood: Remove mill glaze with sandpaper. Set nails

and ll holes, scratches, and gouges with the appropriate

wood ller and let dry completely. Remove all dust with

a wiping cloth. Fill all gaps with a 100% acrylic,

siliconized, paintable caulking, and allow to completely

dry prior to coating.

Previously Painted Wood: Remove all loose and peeling

paint and all other foreign substances. Clean any dirt and

grease by scrubbing the surface with a detergent and water

solution, followed by a thorough rinsing with clean water.

Set nails and ll holes, scratches, and gouges with the

appropriate wood ller and let dry completely. Remove all

dust with a tack or wiping cloth. Fill all gaps with a 100%

acrylic, siliconized, paintable caulking, and allow to completely

dry prior to coating. Glossy Surfaces: For maximum

adhesion, sand the surface thoroughly before coating.

Wood: WARNING! Sanding or scraping pressure treated

lumber may be hazardous; wear appropriate protection.

New Plaster: New plaster should be thoroughly dried

out and cured for a minimum of 30 days before painting.

When cured, clean using a mixed solution of one part

vinegar and one part water to remove eorescence and

neutralize.Previously Painted Plaster: Remove all

loose and peeling paint and all other foreign substances.

Clean any dirt and grease by scrubbing the surface with

a detergent and water solution, followed by a thorough

rinsing with clean water. Set nails and ll holes, scratches,

and gouges with the appropriate spackling material. Let dry

completely and sand smooth. Remove all dust with a tack

or wiping cloth. Fill all gaps with a 100% acrylic, siliconized,

paintable caulking, and allow to completely dry prior to

coating.Glossy Surfaces: For maximum adhesion, sand the

surface thoroughly before coating.

Stainblocking: After priming, test for stain bleed-through

by applying the topcoat to a small section. If the stain bleeds

through the topcoat, apply a second coat of primer and

test again before top-coating the entire area. If bleeding

continues, a longer dry time of the primer may be needed

before top-coating.

Masonry: All masonry surfaces must be cured at least

30 days before painting. The pH must be 10.0 or lower

prior to coating. Smooth masonry may require an adequate

prole for adhesion. For all other smooth trowel concrete,

create a prole using a product such as a muriatic acid etcher

or with mechanical means.

Metal: Ferrous and Non-Ferrous Metals: All metals

1 of 2

i300 INTERIOR SEMIGLOSS PAINT

NO. PR370

COMPLIES WITH THE BELOW AS OF 2/1/2018

SCAQMD YES LEED v.3 (2009)

†

YES

CARB SCM 2007 YES LEED v.4

†

YES

CARB YES MPI# 54, 141, 147

OTC PHASE II YES MPI X-Green 54, 141, 147

OTC YES GREENGUARD®

YES

LADCO YES CHPS YES

AIM YES NAHB/ICC NGBS YES

This coating conforms to USDA regulatory requirements for

incidental food-contact materials intended for use on surfaces

not in direct contact with food, such as walls, oors and ceilings.

†

Please visit www.usgbc.org/LEED for additional details.

GREENGUARD

is a registered trademark of UL Company.

Summary of content (2 pages)

PAGE 1
TECHNIC AL DATA SHEET i300 INTERIOR SEMI-GLOSS PAINT N O. P R 370 PRODUCT INFORMATION COMPLIES WITH THE BELOW AS OF 2/1/2018 BEHR PRO™ Interior Semi-Gloss Paint is a professional quality latex paint with superior hide and coverage, excellent sprayability, spray back-roll and superior touch-up. This product contains an antimicrobial agent to protect the surface of the paint film from mold and mildew.* SCAQMD YES LEED v.3 (2009)† CARB SCM 2007 YES LEED v.
PAGE 2
TECHNIC AL DATA SHEET i300 INTERIOR SEMI-GLOSS PAINT N O. P R 370 should be clean and free of any oils, rust, mill scale or other contaminants. All metals require sufficient “tooth” or profile for optimum adhesion and therefore require some type of sanding, abrasion, or chemical etching. Oil films: (especially on new or non-ferrous metals) should be removed by scrubbing the surface with a detergent and water solution, and thoroughly rinsed.