Use and Care Manual

CAUTION IRRITANT MAY CAUSE EYE, NOSE AND THROAT
IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID
BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION
AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION.
To avoid breathing vapors and spray mist, open windows and doors or use other means
to ensure fresh air entry during application and drying. If you experience eye watering,
headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved
for organic vapor with P series particulate pre-filter) may offer additional protection; obtain
professional advice before using. A dust mask does not provide protection against vapors. Avoid
contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued
difficulty is experienced, get medical assistance immediately. In case of eye contact, flush
immediately with plenty of water for at least 20 minutes and get medical attention; for skin,
wash thoroughly with soap and water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
WHERE TO USE
Ideal for Wood, Vinyl and Fiber Cement Sidings, Stucco, Brick,
Masonry and Fences.
PREPARATION & PRIME
Use on properly prepared and cleaned coated and uncoated Exterior
surfaces. Countersink nailheads, fill and sand smooth. Remove rust,
loose or peeling paint. Repair imperfections and sand smooth. Wash
off dirt, grease and chalk with detergent and/or powerwash. Remove
mildew stains with a mildew stain removing product. Clean and sand
new or weathered wood. Scuff sand or degloss smooth or glossy
surfaces. Scuff sand or etch metals. Rinse and allow to dry. Caulk
windows, doors and other openings. Allow new stucco, plaster and
masonry to cure for 30 days before painting. Use BEHR PREMIUM
PLUS
®
Paint as a primer over properly prepared coated or uncoated
surfaces. For stain-blocking, painting over woods with tannins, or
over oil-based or glossy surfaces, prime with a product such as
BEHR INTERIOR/EXTERIOR MULTI-SURFACE PRIMER & SEALER No. 436.
For drastic color changes or when applying deep colors denoted with
a dagger (†) on the color chip, apply a custom tinted primer if needed.
Prime all metal surfaces before painting.
APPLICATION
Apply product on dry substrates when air and surface
temperatures are between 35°-90°F (2°-32°C) and will remain
between 35°-90°F (2°-32°C) for at least 4 hours after applying.
Do not paint when rain or heavy condensation is expected. Stir
paint occasionally. Intermix containers of same product to ensure
color and sheen uniformity. On semi-smooth surfaces, use a high
quality 3/8-1/2" nap roller cover, nylon/polyester brush or an
airless sprayer (.015-.021" spray tip, 60 mesh filter). On rough
surfaces, use a high quality 3/4-1" nap roller cover. Do not thin if
using a roller or brush; however, if using a sprayer and thinning
is required, thin with water at a rate of no more than 1/2 pint per
gallon. Certain colors may require additional coats for complete
hide. On heavy stains and woods that contain tannins, allow
12-16 hours of dry time between coats. Cooler temperatures
or higher humidity may prolong drying time. After 4 weeks,
cured paint film may be cleaned with a mild, non-abrasive liquid
detergent. Dry paint film is mildew resistant. When applying to
vinyl, color choice must be the same color or lighter than the
existing color. Do not use on floors.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
Visit behr.com for painting tips, expert project advice, and the perfect
color coordination with the ColorSmart by BEHR
®
Tool.
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.
Wear a NIOSH-approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS
©2019 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. < 50 g/L • REV. 08/19
No. 9050 Ultra Pure White
®
No. 9300 Deep Base
No. 9400 Medium Base
1 Hr Dry Time
2 Hr Recoat Time
250-400 Sq. Ft.
Coverage per Gallon
Protect
from Freezing
Soap & Water
Clean-Up
• Paint & Primer in One
• Excellent Hide
• Helps Resist Moisture, Fading & Stains
• Enhanced Adhesion Helps Resist Peeling
• Mildew Resistant Finish
• Low VOC
• 100 % Acrylic
• Lifetime Warranty*
BEHR PREMIUM PLUS
®
Exterior Satin Enamel
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov
*LIFETIME LIMITED WARRANTY Behr Process Corporation warrants to you, the original
residential consumer purchaser, the performance of this product as described on this label
for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS
NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE
WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to
perform as specified on the label during the warranty period, Behr Process Corporation will, at
its option and upon presentation of proof-of-purchase (the original receipt), either furnish an
equivalent amount of new product or refund the original purchase price of this product to you.
This warranty excludes (1) labor and costs of labor for the application or removal of any
product, and (2) any incidental or consequential damages, whether based on breach
of express or implied warranty, negligence, strict liability or any other legal theory.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This warranty gives you specific legal
rights and you may also have other rights, which vary from state to state. Note to residents of
the State of New Jersey: The provisions of this warranty, including its limitations, are intended
to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain
warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect
any and all application of the product prior to processing your claim made under this warranty.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).