Use and Care Manual

WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov
WARNING! CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT
IRRITATION. Avoid contact with skin and eyes and avoid breathing vapors, spray mist and
sanding dust. Sanding, grinding or abrading may release sanding dust, which may be harmful
if inhaled and has been shown to cause lung damage or cancer with long term exposure. Do
not breathe dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open
windows and doors or use other means to ensure fresh air entry during application, drying,
sanding, and/or abrading. If properly used, a respirator (NIOSH approved with particulate pre-
filter) may offer additional protection and should be used if adequate ventilation cannot be
provided; obtain professional advice before using. If you experience eye watering, headaches,
or dizziness during application or drying, increase fresh air or leave the area. Avoid contact
with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST
AID: if you experience difficulty in breathing, leave the area to obtain fresh air. If continued
difficulty is experience, get medical assistance immediately. In case of eye contact, flush
immediately with plenty of water for at least 20 minutes and get medical attention; for skin,
wash thoroughly with soap and water. If swallowed, get medical attention immediately.
KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
*LIFETIME LIMITED WARRANTY Behr Process Corporation warrants to you, the original residential
consumer purchaser, the performance of this product as described on this label for so long as you
reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED
TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS.
This warranty is not transferable. If this product is found not to perform as specified on the label
during the warranty period, Behr Process Corporation will, at its option and upon presentation of
proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund
the original purchase price of this product to you. This warranty excludes (1) labor and costs of
labor for the application or removal of any product, and (2) any incidental or consequential
damages, whether based on breach of express or implied warranty, negligence, strict liability
or any other legal theory. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This warranty
gives you specific legal rights and you may also have other rights, which vary from state to state.
To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to
inspect any and all application of the product prior to processing your claim made under this warranty.
To consult with a Behr Paint Company Representative, call 1-800-854-0133 Ext. 2 (U.S.A. only).
BEHR PREMIUM PLUS
®
Exterior Satin Enamel
• Paint & Primer
◊
• Excellent Hide
• Helps Resist Moisture,
Fading & Stains
• Enhanced Adhesion Helps
Resist Peeling
• Mildew Resistant Finish
• Low VOC
• 100 % Acrylic
• Lifetime Warranty*
No. 9050 ULTRA PURE WHITE
®
No. 9300 Deep Base
No. 9400 Medium Base
1 Hr Dry Time
2 Hr Recoat Time*
250-400 Sq. Ft.
Coverage per Gallon
Soap & Water
Clean-Up
Protect
from Freezing
FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS
WHERE TO USE
Ideal for Wood, Vinyl and Fiber Cement Sidings, Stucco, Brick,
Masonry and Fences.
PREPARATION & PRIME
Use on properly prepared and cleaned coated and uncoated Exterior
surfaces. Countersink nailheads, fill and sand smooth. Remove rust, loose
or peeling paint. Repair imperfections and sand smooth. Wash off dirt,
grease and chalk with detergent and/or powerwash. Remove mildew
stains with a mildew stain removing product. Clean and sand new or
weathered wood. Scuff sand or degloss smooth or glossy surfaces.
Scuff sand or etch metals. Rinse and allow to dry. Caulk windows, doors
and other openings. Allow new stucco, plaster and masonry to cure for
30 days before painting. Use BEHR PREMIUM PLUS
®
Paint as a primer
over properly prepared coated or uncoated surfaces. For stain-blocking,
painting over woods with tannins, or over oil-based or glossy surfaces,
prime with a product such as BEHR
®
INTERIOR/EXTERIOR MULTI-
SURFACE PRIMER & SEALER No. 436. For drastic color changes or when
applying deep colors denoted with a dagger (†) on the color chip, apply a
custom tinted primer if needed. Prime all metal surfaces before painting.
APPLICATION
Apply product on dry substrates when air and surface temperatures are
between 35–90°F (2–32°C) and will remain between 35–90°F (2–32°C)
for at least 4 hours after applying. Do not paint when rain or heavy
condensation is expected. Stir paint occasionally. Intermix containers
of same product to ensure color and sheen uniformity. On semi-smooth
surfaces, use a high quality 3/8–1/2" nap roller cover, nylon/polyester
brush or an airless sprayer (.015–.021" spray tip, 60 mesh filter). On
rough surfaces, use a high quality 3/4-1" nap roller cover. Do not thin
if using a roller or brush; however, if using a sprayer and thinning is
required, thin with water at a rate of no more than 1/2 pint per gallon.
Certain colors may require additional coats for complete hide. On heavy
stains and woods that contain tannins, allow 12–16 hours of dry time
between coats. Cooler temperatures or higher humidity may prolong
drying time. After 4 weeks, cured paint film may be cleaned with a mild,
non-abrasive liquid detergent. Dry paint film is mildew resistant. When
applying to vinyl, color choice must be the same color or lighter than the
existing color. Do not use on floors.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags,
contact your household refuse collection service.
Visit behr.com for painting tips, expert project advice, and the perfect
color coordination with the ColorSmart by BEHR
®
Tool.
WARNING If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. Contact the National Lead Information Center at
1-800-424-LEAD or log on to www.epa.gov/lead.
©2021 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. < 50 g/L • REV. 06/21
◊
A primer coat may be needed on some surfaces. See back label for details.