TDS

TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2016 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 6/2016
2 of 2
wool, abrasive blasting, or other abrading methods.
Prole: For best adhesion results, sand all metal surfaces
(including new ones) with sandpaper, steel wool, or etch
using a product such as a muriatic acid. Clean by scrubbing
the surface with a detergent and water solution, followed by
a thorough rinsing with clean water. All ferrous metals must
be primed the same day it is cleaned to prevent rust.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Wood: Cedar, Redwood, Shakes & Shingles;
For Severe Tannin Bleed/Stainblocking:
• BEHR PREMIUM PLUS® Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry: Stucco, Cinder Block, Cut Masonry Units
(CMUs), Split Face Block
• BEHR PREMIUM® Interior/Exterior Basement & Masonry
Waterproofer No. 875
Masonry: Cement Composition Panels/Siding,
Exterior Insulation and Finish Systems (EIFS)
or Synthetic Stucco
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875
Masonry with pH Levels up to 13.0:
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Ferrous and Non-Ferrous Metals:
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
PREVIOUSLY PAINTED SURFACES:
• Use a full coat, or spot prime repaired, or uncoated
surfaces, such as woods with heavy tannins
(Redwood and Cedar) with BEHR MARQUEE® Paint.
Two coats may be required.
TEST SPECIFICATIONS:
Scrubbability:
ASTM D2486 Scrub > 2500 (no shim)
Biological Growth:
ASTM D3273 (4 weeks) – Pass
Accelerated Weathering:
ASTM D4587, 500 hrs exposure - Pass
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between 35°F - 90°F.
Temperatures above 90°F may aect the dry time.
• Avoid heavy trac for 24 hours.
• Allow four weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, and eye & face protection. Do not
eat, drink, or smoke when using this product. Take o
contaminated clothing and wash it before reuse.
Wash hands thoroughly after handling. Dispose of unused
contents, container and other contaminated wastes in
accordance with local, state, federal and
provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
EXTERIOR SEMIGLOSS ENAMEL PAINT
NO. 5450 ULTRA PURE WHITE®