23456789012345678901234567890121234567890123456789012345678901212345678901 123456789012345678901234567890121234567890123456789012345678901212345678901 123456789012345678901234567890121234567890123456789012345678901212345678901 123456789012345678901234567890121234567890123456789012345678901212345678901 123456789012345678901234567890121234567890123456789012345678901212345678901 123456789012345678901234567890121234567890123456789012345678901212345678901 12345678901234567890123456789012123456789012345678901234
WOW Study Carrel Part Drawing Description Adjustable Height Workcenter Qty Part P1 Right Side Panel 1 EA P8 P2 Left Side Panel 1 EA P9 P3 Top Platform 1 EA Drawing Description Qty Stability Brace 1 EA Metal Angle Bracket 8 EA Hardware List P4 P5 P6 P7 Upper Shelf Platform Back Panel Upper Leg Reciever Lower Leg Insert A ½” Socket Screw 4 EA A1 1-½” Socket Screw 8 EA B Threaded Nut 4 EA C Wood Screw 24 EA D Plastic Grommet 2 EA E Leveling Glide 4 EA F Allen
Study Carrel Assembly Diagram READ THROUGH INSTRUCTIONS FROM BEGINNING TO END BEFORE STARTING TO ASSEMBLE UNIT. P4 1.) Identify and Separate all the Parts and Hardware. G Illustration # 1 2.) Place the Upper Shelf Platform (P4) with the Holes facing up and install 6 each Cam Locks (G) into the large holes as shown in illustration # 1. Illustration # 2 P4 G H Be sure that arrow on top of Camlock (G) aligns with centerline of Edge Drilled hole. Phillips Screwdriver 3.
Illustration # 3 5.) Place the Left Side Panel (P2) with the insert nuts facing up. P2 H 6.) Install 6 each Cam Posts (H) in the 6 threaded insert nuts (Pre-installed) as shown in illustration # 3. 7.) Repeat Steps 5 & 6 for the Right Side Panel(P6). G P2 8.) Place the Top Platform (P3) with the Holes facing up and install 6 each Cam Locks (G) into the large holes as shown in illustration # 4. G P3 P4 Illustration # 4 9.) Place the Back Panel (P5) with the insert nuts facing up.
Illustration #6 11.)Attach to the Right Side Platform (P1) and the Left Side Panel (P2) to the Top Platform (P-3), the Back Panel (P5), and the Upper Shelf Platform (P-4) as shown in illustration # 6. H P1 P3 H P4 G P2 G P5 P1 P3 12.) Attach 6 each Metal Angle Brackets (P9) using 18 each (C) screws as shown in illustration # 7. P2 C (C) Screw #6 X ½ For Scale only P1 P9 C P2 P4 Illustration #7 P9 13.
14.) Rotate the Carrel Assembly so that the Bottom Platform (P-3) is facing up. Attach 2 each Upper Receivers (P6) to the Bottom Platform (P-3) using 4 each (A1) screws as shown in illustration #9. (Finger tighten only) P6 A1 A1 P6 B A1 15.)Attach Stability Brace(P8) to the 2 each Upper Receivers (P6) using 4 Screws (A1) and 4 Threaded Nuts (B) as shown in illustration #6. P8 B A1 P3 (A1) Screw M6 X 1-½” For Scale only E Illustration #9 E E 16.
Grommet(D) installation Illustration #11 Grommet (D) 18.) To install Grommet (D), separate parts and press Grommet Sleeve in Round openings in Bottom Platform (P3) and Back Panel (P4) as shown in illustration #8. Cap 19.) Snap plastic Caps into Sleeves as shown in illustration #11. Sleeve Cap Sleeve P3 P3 D Important The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase.
9788-Study Carrel Workcenter For more information 1-800-749-2258 37 ½ 35 X 8¼ 12 Clearance 19½ ½ 35 X 22 Adjustable Height 22 - 30 23 22 30½ Shipping Information 5.1 Cubic Feet 92 lbs.
