www.MBTubs.com Phone # 512-522-2284 E-mail : info@MBTubs.
Warranty and Registration …………………………………………………………………….3 - 6 Important Safety Instructions ……………………………………………………………………..7 Unpack and Inspect ………………………………………………………………………………..8 Preparing for Installation …………………………………………………………………………..9 Installation of Bath ………………………………………………………………………………..10 Plumbing Installation ………………………………………………………………………….11-13 Installing Faucet System …………………………………………………………………….14-18 Electrical Installation Requirements…………………………………………………………….
Mobility Bathworks Walk in Bath are warranted in accordance with the following warranty : This warranty is extended to the first purchaser and does not extend to products previously used as display models or products that have been modified or repaired by anyone else but Mobility Bathworks unless approved by Mobility Bathworks . Mobility Bathworks Hi Gloss Gel Coat Tubs are backed by a thirty ( 30 ) Year Warranty. Five ( 5 ) year warranty on the tub components and Lifetime Warranty on the door seal.
Name : __________________ Address : ______________________ City : ____________ State:_______ Zip:________ Telephone:__________________ Email:_________________ Upon completing the installation of an Mobility Bathworks walk in tub: the following activation form must be completed , signed by both the customer and installer , and returned to Mobility Bathworks In order for the warranty to be activated ( faxed, scanned or emailed, or hard copy mailed ) To be initialed by the installer(s) ____ Walk in Tub is leve
Name : __________________ Address : ______________________ City : ____________ State:_______ Zip:________ Telephone:__________________ Email:_________________ Model : ________________ Serial # ________________ Purchase Date : _______________ Purchase Price:_______________ Place of Purchase :___________________________________ Contact Name : ______________________ Phone # _______________________ Upon completing the installation of an Mobility Bathworks walk in tub: the following activation form must be co
1. To ensure that your warranty is granted please fill out the product registration form in 30 days and email it to : info@mbtubs.com fax to 866-833-2395 or Mail it to : Mobility Bathworks 308 W Broad St Quakertown, PA 18951 2. By filing out the form the manufacturer will be able to process and warranty claims. 3. The information provided on the product registration form will be kept on file by Mobility Bathworks.
1. Please read through the entire manual completely before beginning installation 2. Contact a licensed & bonded plumber and electrician for installation. The Mobility Bathworks is intended for indoor use only ! Install the tub in accordance with the instructions and parts in the manual. 3. Make sure to have a licensed electrician test all connections to the dedicated line, including GFCI. RISK IF ELECTRIC SHOCK : Do not permit electric appliances within 3 feet ( 1.5 meter ) of the tub i.
1. While unpacking your MBTUBS walk in tub inspect the product and packing thoroughly for freight damages. If there are any noticeable damages ** DO NOT ACCEPT the unit from the carrier ** and call us as soon as possible at : 512-522-2284 2. Upon receiving your Mobility Bathworks Walk in Tub, please open immediately and check for any damages : Damages due to delivery must be reported to Mobility Bathworks within 48 hours of receipt.
Remove access panels that are held on by magnets. Remove these by using the yellow suction cups on the panel and put them in safe place until installation is complete. Use Suction Cup to take Off Panel Place all accessories to the side. Make sure no loose parts are hanging. Lift and carry the bath only by the deck or frame. Protect the bottom of the bath to avoid breaking the jets at the bottom. Only accessories approved by Mobility Bathworks walk in tub should be used with this product.
1. Remove the existing tub and the wall and floor materials as required. 2. Clean area of any debris or trash. 3. Use 4 Foot level and determine if the floor is level. If the floor is not level adjust all leveling feet to perfect level the tub. 4. Make sure you level the Walk in Tub from the highest elevation point on the floor. 5. All leveling legs of the walk in tub must be resting on the floor evenly supporting the weight of the bathtub, in order for the door to work properly without leaks. 6.
1. Dry fit the plumbing before final assembly to make sure that the pipe lengths are correct and there is proper clearance throughout. 2. Make sure the hole around the drain is leveled under the tub. If not sand down with sandpaper. 3. Assemble kit as shown. Check your local plumbing codes to insure that proper fixatives ( glue ) are used. 4. Tighten down the nuts. 5. Install Overflow elbow with gasket. Secure to the tub with retaining plate and nut, install cover plate and secure with set screw. 6.
1. Dry fit the PVC pipe prior to final assembly to ensure the lengths are correct. Orient Tee as shown. 2. Glue fittings using appropriate cement and primer as required by local codes 3. Mount the 4 ear washer gasket on the overflow behind the tub. Place silicone or plumbing putty between gasket between bathtub and bath show elbow under side of tub. 4. Place a thin bead of silicone caulking around the strainer piece and place it in the tub outlet.
1. To install the faucet set, begin by using masking tape on the fiberglass surface over the are to be marked-off and drilled. 2. Mark the position of the holes for the faucets / taps onto the taped off area. Be sure that your piping will not be obstructed by the walk in tub stainless steel framework or any other obstacle. Remember : Measure twice and cut once. 3. To cut the holes use a coring bit. Using the tape to help with a clean cut, drill through the surface. 4.
Mobility Bathworks Gel Coat Walk in Tubs comes with one of two types of faucets . 1. One Piece Chrome Finish Bristan Faucet 2. 5 Piece Roman Faucet in Chrome Finish Full body brass sprout Hand Shower with pull out hose Diverter for sprout and hand shower Hot and Cold Water control valves 7.25” Hole size of 1.
Make sure to fill out Huntington Brass Warranty and Send to : HB Faucets 11100 Dana Circle Cypress, CA 90630 18
Installation of electrical components must be done by a licensed electrician. Important : All units need a NEMA plug to be plugged into a GFCI outlet that is connected to a separate circuit with a 20 AMP breaker run directly from breaker panel box. *** Warning *** If the GFCI fails to operate, there is ground current flowing, indicating the possibility of electrical shock. Do not use your walk in tub until a repairman has addressed the fault.
Air Jets - Push Once for ‘ High ‘ - Push Twice for ’ Medium’ - Push Three Times for ‘ Low ’ - Push Again for ‘ OFF ‘ Features : 3 Speed Air Switch; High, Medium and Low 20 Minute Timer 500 Watt Air Blower Motor 300 Watt Ceramic Air Heater Included 1 Minute Purge Cycle 20 Minutes after the system has been turned off Specially designed for a quieter performance CSA, CSA-US, UL Approved Specs 120 Volts / 5.
Waterways Pumps Specs : 5.
Water Jet System Push Once for ‘ ON ‘ Push Twice for ‘ OFF ‘ Air Massage On/ Off Water Jet Pressure Control Valve 22
After both the electrical and plumbing installation are done, a final inspection of these parts needs to be completed before finishing the installation. Close the drain and fill the walk in tub until it is up to a normal water height level which is 1” to 2” below the overflow and drain lever. Overflow and Drain Lever Open Closed Allow the water to stand in Walk in Tub for 30 minutes and then inspect all plumbing and seats for leaks.
Inspect the unions around the pump; if leaks persist from the unions after tightening: loosen the unions and insure that the O-ring is seated properly. If the pumps do not operate check the breaker to insure power is on and the cable connection to the controls to the pump is attached. If that doesn’t work make sure all clear hoses are securely placed in the nipple of the air button and pump. Ensure all jets are opening and working. Make sure they operate at all speeds.
An extension box is used to extend the length of your Mobility Bathworks to a 60” Length. Some installations require trimming the extension panel. Cutting the extension pieces should be done with reciprocation saw: a progressive blade is best or a bi metal blade will work as well. Measure the distance between the wall and the walk in tub by the three corners and at the middle of each length so as to detect any variance in the shape of the wall.
Drill hole on the frame and install the hardware as shown in the picture. Screw with spring on the left and right upper part of stainless frame. Screw with bracket on the bottom part stainless frame. Adjust the bracket to fit end panel.
Drill Holes on the end panel for the screw. Adjust the hole to install the screw with the bracket on the stainless steel frame. Install the cap on the screw.
1. Entering Your Mobility Bathworks Walk in Tub Enter your Walk in Tub then close and seal the door by pulling the handle toward you, into locked position. Warning : The Walk in Tub door handle is put together with the strongest material available, but it’s NOT A GRAB BAR. It will not withstand a person putting their entire entire weight against it while either trying to pull themselves up out of the bath of using excessive force closing the door.
Omni handle : Is a walk in tub handle that is connected to the top of the door to a locking mechanism that’s inside the walk in tub door. Turn counter-clockwise to lock and turn clockwise to un-Lock. Wheelchair * Outward Swinging * handle : Push the handle forward to lock so the pins lock into the walk in tub frame securely. Pull handle back to unlock so the pins release from walk in tub frame causing the accessible tub to open.
One Piece Bristan Faucet Contemporary Showerhead Diverter Cold Valve Warm Valve 5 Piece Roman Faucet Roman Sprout Warm Valve Cold Valve Diverter 30 Roman Showerhead
1. Using the Pumps… The water level in your walk in tub must be approximately 2” above the jets before the Air or Water jet systems should be turned on to avoid possible damage to the pumps. If you have a dual, we don’t recommend running both systems at the same time since they have the opposite effect therapeutically. Recommended maximum time of use for hydrotherapy system is 20 minutes. If the three speed air jet system left on it will automatically shut itself off after 20 minutes.
Regular care of you Mobility Bathworks walk in tub will keep it clean and have it working at its best for many years to come. The best way to counteract from detrimental affects occurring is to prevent water from remaining on any finished surface on the Walk in Tub. Wipe down your Walk in Tub after every use. Please clean out your spa system with Cascade every 2 weeks to keep spa system clean.
Question # 1: The door seal isn't completely compressed. Should I try adjusting the door to make it tighter ? Answer # 1: NO, there is no need to. Never adjust, move, undo or tamper with the door hinge. In some cases the door seal needs to reform its shape. This can easily be done by allowing the door to stay open when not in use. Question # 2: How often should I clean my Mobility Bathworks Walk in Tub ? Answer #2: Wipe your walk in tub off after each use.
