Use and Care Manual

ManualsBrandsAvallon ManualsBeverage Coolers24" Built-In or Free Standing Beverage Cooler - Left Swing Door

Installation

The refrigerator should be installed in accordance with local electrical code requirements. The refrigerator

should also be placed in a locaon that is strong enough to support its total weight, keeping in mind that it will

weigh substanally more when fully loaded than when empty. Before you plug the refrigerator into a power

supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to sele.

Unpacking the Refrigerator

Warning: Use two or more people to move and install the refrigerator. Failure to do so can

result in back or other injury. Carefully remove the packaging materials. Remove any shipping

tape and glue from your refrigerator before use. Do not use sharp instruments, rubbing alcohol,

ammable uids, or abrasive cleaners to remove tape or glue. These products can damage the

surface of your refrigerator.

Warning: Do not remove any safety, warning, or product informaon labels from your refrigerator.

Warning: DO NOT install the refrigerator behind a closed cabinet door.

This refrigerator has been designed for freestanding or built-in installaon. In each case, there must be adequate

venlaon and access for service.

Freestanding Installaon:

A freestanding installaon will allow you to install the refrigerator in almost any place you desire. You must

follow the stated instrucons for electrical requirements and leveling the refrigerator.

Built-in Installaon:

A built-in installaon will allow you to install the refrigerator under a counter as long as the required clearance

space around the refrigerator is provided. It is necessary to allow adequate venlaon space around the unit,

including at the back of the unit.

The following addional items must be observed:

1. Place the refrigerator in front of the installaon locaon. Adjust the feet and place the unit at on the oor or

on a plaorm depending on your installaon requirements.

2. If the electrical outlet for the refrigerator is behind the cabinet, plug in the refrigerator.

3. Push the refrigerator into posion.

Types of Installation

Summary of content (8 pages)

PAGE 1
Installation The refrigerator should be installed in accordance with local electrical code requirements. The refrigerator should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded than when empty. Before you plug the refrigerator into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
PAGE 2
Clearance Requirements Notes: • To ensure proper service access and ventilation, allow between 1 - 2 inches of clearance at the back as shown in the diagram. • The installation should allow the unit to be pulled forward for servicing, if necessary. • A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance with National Electrical Code and local codes and ordinances, is required. When installing the refrigerator under a counter, follow the recommended spacing dimensions shown.
PAGE 3
Electrical Requirements ELECTRIC SHOCK HAZARD! • Plug into a grounded 3-prong outlet. • Never remove the grounding prong from the plug. • Never use an adapter to bypass the grounding prong. • DO NOT use an extension cord. • Failure to follow these instructions can result in fire, electrical shock, or death.
PAGE 4
Leveling the Refrigerator The refrigerator should be installed on a firm and level surface that will be able to support the entire weight of a fully loaded unit. It is important for the refrigerator to be leveled in order to work properly. It can be raised or lowered by rotating the plastic sheaths around each of the feet on the bottom of the machine. If you find that the surface is not level, rotate the feet until the refrigerator becomes level. You may need to make several adjustments to level it.
PAGE 5
Installing the Shelves To prevent damaging door gasket, make sure to open the door fully before pulling the shelves off their tracks. 1. Open the door completely. 2. Ensure that the metal guide posts are attached to the back of the shelf. 3. While lifting the right side of the shelf up 45°, rest the left metal guide post on the shelf track. 4. Slowly push the shelf back until the right metal guide post reaches the vertical indentation in the cabinet. 5. Gently set the shelf down on the track.
PAGE 6
Operation Installation Checklist before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the refrigerator? 2. Have the installation instructions been followed, including connecting the machine to electricity? And has proper grounding been installed for the refrigerator? 3. Has the machine been leveled? 4. Is the refrigerator in a site where the ambient temperature is between 50° F and 90° F all year round? 5.
PAGE 7
Sabbath Mode This refrigerator is programmed with a Sabbath Mode. In Sabbath Mode, the refrigerator will continue to cool and maintain temperature. However, the refrigerator will no longer respond to user interactions. All lights, display(s), and indicators are turned off, and all alarms are disabled. To enter Sabbath Mode, hold the Power button and press the Up button twice. The control panel will beep twice indicating that the refrigerator is in Sabbath Mode.
PAGE 8
Normal Sounds Your new refrigerator may make noise during normal operation. Most of these sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder than they actually are. The following describes several sounds you may hear and what may be making them: • Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the refrigerator can also make noises. • The high efficiency compressor may make a pulsating or high-pitched sound.