INSTRUCTION MANUAL WTLD018 20V Drill/Driver
Contents Warranty Introduction Environmental protection Description of symbols Specifications Safety instructions Additional safety instructions for drills Additional safety instructions for the charger Additional safety instructions related to the battery pack and battery safety When to charge the battery Know your product Unpacking Important information – Product care Fitting and removing the battery pack Battery charging To obtain the best life for the battery Battery indicator Battery indicator under no
Description of symbols Introduction The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. Wear hearing protection. Wear eye protection. Wear breathing protection. Your new AUTOMATIC power tool will more than satisfy your expectations. It has been manufactured under stringent AUTOMATIC Quality Standards to meet superior performance criteria.
General safety rules f) If operating the charger in a damp location is unavoidable, use a residual current device (RCD) protected supply with a max 30mA cut off limit. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Only use accessory bits in good condition. • Before drilling, check that there is sufficient clearance for the drill bit under the workpiece. • Do not touch the bit after operation. It will be very hot. • Keep your hands away from under the workpiece. • Never use your hands to remove sawdust, chips or waste close by the bit. • Rags, cloths, cord, string and the like should never be left around the work area. • Support the work properly.
it will not be stepped on, tripped over or otherwise subjected to damage or stress. Keep the lead away from operating machinery. • Do not pull on the lead of the charger to disconnect it from the mains power socket. • Do not use an extension cord unless it is absolutely necessary. The use of an improper extension cord could cause the risk of fire, electric shock or electrocution. • Never attempt to connect two chargers together.
electricity is generated nor let the battery touch something that is statically charged. • The battery can be stored at temperatures between 0 - 40° C. NEVER STORE OR LEAVE YOUR LITHIUM ION BATTERY IN TEMPERATURES OVER THAT RECOMMENDED OTHERWISE FIRE MAY OCCUR.
Know your product 11 10 This drill is mainly used for drilling in wood or metal sheet and screwdriving. Use the tool and accessories only for intended applications. All other applications are expressly ruled out. 1. Keyless Chuck 1 2. Handle 16 3. Variable speed trigger switch with electric brake 4. Forward, Lock, Reverse control 9 12 5. Rechargeable lithium ion battery pack 6. LED battery indicators 7. Battery pack release button 8. Torque adjustment collar 8 9. 2 Speed gear selector 11.
Unpacking In this condition, DO NOT force cool the pack by placing in a freezer or similar device. Refer to the “Overload” section in this manual. Another feature of the drill/battery pack is the low voltage cut out feature. This feature operates when the voltage drops below a pre set value. When this occurs the tool will automatically stop operating.
Battery charging To obtain the best life for the battery IMPORTANT. Before attempting to charge the battery, check the charger and the battery to ensure the charging equipment matches the battery supplied. The components are all labelled with component numbers. IMPORTANT. The battery will be fully charged after 3-5 hours, remove it from the charger after this time. Do not leave a battery charging for longer than 24 hours. Note: It is suggested to remove the battery from the drill for the charging process.
Battery Indicator Under No-load Red Orange Green Battery status LED LED LED indicator/description ON ON ON High: Battery is fully charged ON ON OFF Medium: Battery Approx 50% charge capacity. ON OFF OFF Low: Battery has less than 30% charge capacity and should be charged. WARNING: Never use a damaged battery pack.
Temperature Cut Out If the drill is constantly overloaded, or the drill is used constantly at maximum rating in high ambient conditions, the battery cells may over heat causing the battery pack to shut down. When this occurs you will need to immediately stop drilling and allow the battery cells to reduce the temperature. To reduce the temperature of the cells remove the battery pack from the drill and place the battery pack in a free air environment, out of direct sunlight or any other heat source.
Adjustable torque These drills are equipped with 24 torque settings plus one drill setting which are controlled by the torque collar (8). All of the torque settings are clearly identified on the torque collar. To adjust the torque setting you rotate the torque collar. Rotate the torque collar clockwise to increase the torque setting and rotate it anti-clockwise to decrease the torque setting.
Maintenance Drilling wood • Clamp a piece of scrap wood to the back of your work to prevent splintering. All drilling operations • Mark off the centre of the hole using a centre punch or nail. • Don’t force the drill, let it work at its own pace • Keep the drill bit sharp. • Reduce pressure, as the drill is about to break through the item being drilled. • Store the tools, instruction manual and where necessary the accessories in the original packaging.
DISTRIBUTED BY; Global Power Brands International Pty. Ltd. PO Box 413 Mooroolbark VIC 3138 ABN. 39 131 999 914 Ph. 1800 909 909 help@globalpowerbrands.
