2800 SERIES Models 2801, 2811
Table of Contents WARNINGS . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . 3 CHECKING PACKAGE CONTENTS . . . . . . . . . 3 SYSTEM FEATURES. . . . . . . . . . . . . . . . . 4 APPLICATIONS. . . . . . . . . . . . . . . . . . . . 5 HDMI EXTENSION. . . . . . . . . . . . . . . . . . 5 HDMI DISTRIBUTION NETWORK. . . . . . . . . . 6 TROUBLESHOOTING . . . . .
INTRODUCTION Thank you for purchasing this 2800 Series HD-IP™ distribution system from Audio Authority®. The 2800 Series transmits HDMI® signals from one source over a dedicated Gigabit network via Cat 5e/6 cables to achieve distances many times those possible using an HDMI cable. Ultra high speed GbE (Gigabit Ethernet) preserves ultra high quality 720p or 1080p video content. This manual presents one to one, and one to many configurations.
SYSTEM FEATURES • Supports 720p and 1080p and embedded digital audio (2-channel PCM) • Gigabit Ethernet (GbE, 1000BASE-T) technology for excellent picture quality • Uses off-the-shelf GbE network switches for distribution • Requires only one UTP cable per position (Cat 5e or Cat 6) • Quick synchronization means maximum up-time • Basic installation is plug and play – no complex setup routines or programming • Designed to function on a separate, dedicated Gigabit Ethernet network • Cascading multiple network
APPLICATIONS HD-IP is designed to function as an HDMI extender (point to point), or as a distribution system via a dedicated network (single source). HDMI EXTENSION SOURCE Model 2801 HDMI The example below depicts the HD-IP system in a basic HDMI extension application. NOTE: DIAGRAMS DO NOT SHOW POWER SUPPLY CONNECTIONS TV Model 2811 HDMI In extension applications (point to point), the transmitter may be connected directly to the receiver, for distances up to 250 ft. (75m), using Cat 6 cable.
DISTRIBUTION NETWORK In distribution network applications, a single transmitter (or multiple transmitters) may be connected to several receivers, for distances up to 250 ft. (75m) using Cat 6 cable. Cat 5 cable may also be used, but distances will vary depending on the quality of the cable used. A Gigabit Ethernet (GbE) switch is used in the Cat 6 path to distribute the video signals.
1. With power disconnected from the 2811 Receiver, Tip = Signal Tip = (+) connect your IR receiver and its power supply to Ring = Ground a standard 12V IR connecting block. Connect a = (–) SleeveSleeve = +12 Volts MONO 3.5mm cable from the emitter output of the connecting block to the 2811’s 3.5mm IR port. Pin out is shown. IR 2. With power disconnected from the 2801 Transmitter, connect a standard IR emitter to the 2801’s IR 3.5mm IR port. Pin out is shown.
TROUBLESHOOTING • Poor image quality: For the best results, always use high quality 720p or 1080p content. Some sources, particularly cable and satellite providers, transmit compressed video resulting in poor image quality. Consider the source material when planning and troubleshooting your system. The 2800 Series does not require any adjustment.
CONSIDERATIONS FOR GETTING THE BEST RESULTS Many factors influence the quality and reliability of an HDMI® signal distribution installation. The following are the main factors to consider, and basic precautions that will ensure the best possible performance. • Dedicated network. The 2800 Series is designed to operate on a dedicated Gigabit Ethernet network, not to be combined with other network traffic competing for access to the internet. • Resolution tracking. The 2800 Series supports 720p and 1080p.
SPECIFICATIONS DIGITAL AUDIO/VIDEO I/O 2801 Transmitter 1x via HDMI connector – HDMI input 2811 Receiver 1x via HDMI connector – HDMI output CAT 5E/6 CONNECTIONS I/O 2801 Transmitter 1x via RJ-45 – Cat 5e/6 output 2811 Receiver 1x via RJ-45 – Cat 5e/6 input VIDEO PERFORMANCE Minimum resolution 720p Maximum resolution 1080p (1920x720, 1080p/60Hz) TMDS clock speed (HDMI) 225MHz Data bit rate (HDMI) 2.25Gbps Maximum range 250 ft. (75m) direct connection 1000 ft.
LIMITED WARRANTY If any consumer product from Audio Authority® fails due to defects in materials or workmanship within one year from the date of the original sale to the end-user, Audio Authority guarantees that we will replace the defective product at no cost. Freight charges for the replacement unit will be paid by Audio Authority (ground service only).
2048 Mercer Road, Lexington, Kentucky 40511-1071 Phone: 859-233-4599 • Fax: 859-233-4510 Customer Toll-Free USA & Canada: 800-322-8346 www.audioauthority.
