User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 (optional) Front bezel
- 2.6 Storage devices
- 2.7 Expansion slot
- 2.7.1 Installing an expansion card to riser card bracket 1 (for standard model)
- 2.7.2 Installing an expansion card to riser card bracket 2 and 3 (for standard model)
- 2.7.3 Installing a GPU card to riser card bracket 1 (for GPU model)
- 2.7.4 Installing a GPU card to riser card bracket 2 and 3 (for GPU model)
- 2.7.5 Installing an expansion card to riser bracket 4
- 2.7.6 Installing an ethernet expansion card to riser bracket 4
- 2.7.7 Replacing an HBA/RAID expansion card to riser bracket 4
- 2.7.8 Installing the Cache Vault Power Module
- 2.7.9 Installing an OCP 3.0 card
- 2.7.10 Installing an M.2 (NGFF) card
- 2.7.11 Configuring an expansion card
- 2.8 Cable connections
- 2.9 Backplane cabling
- 2.10 Storage device configuration and cabling
- 2.11 Removable/optional components
- 2.12 Rail Kit Options
- Chapter 3: Motherboard Information
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Performance Tuning menu
- 4.5 Advanced menu
- 4.5.1 Trusted Computing
- 4.5.2 Redfish Host Interface Settings
- 4.5.3 AMD CBS
- 4.5.4 Onboard LAN Configuration
- 4.5.5 Serial Port Console Redirection
- 4.5.6 CPU Configuration
- 4.5.7 PCI Subsystem Settings
- 4.5.8 USB Configuration
- 4.5.9 Network Stack Configuration
- 4.5.10 NVMe Configuration
- 4.5.11 SATA Configuration
- 4.5.12 APM Configuration
- 4.5.13 AMD Mem Configuration Status
- 4.5.14 T1s Auth
- 4.5.15 Driver Health
- 4.5.16 Third-party UEFI driver configurations
- 4.6 Chipset menu
- 4.7 Security menu
- 4.8 Boot menu
- 4.9 Tool menu
- 4.10 Event Logs menu
- 4.11 Server Mgmt menu
- 4.12 Exit menu
- Chapter 5: Driver Installation
- Appendix
4-50
Chapter 4: BIOS Setup
Configure IPV4 support
DM_LAN/Shared LAN
Configuration Address source [Previous State]
This item allows you to configure LAN channel parameters statistically or dynamically
(by BIOS or BMC). [Previous State] option will not modify any BMC network
parameters during BIOS phase.
Configuration options: [Previous State] [Static] [DynamicBmcDhcp]
[DynamicBmcNonDhcp]
The following items are available only when Configuration Address source is set to
[Static].
Station IP address
Allows you to set the station IP address.
Subnet mask
Allows you to set the subnet mask. We recommend that you use the same
Subnet Mask you have specified on the operating system network for the
used network card.
Router IP Address
Allows you to set the router IP address.
Router MAC Address
Allows you to set the router MAC address.
4.11.2 BMC network configuration
The sub-items in this configuration allow you to configure the BMC network parameters.