User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to riser card bracket 1
- 2.6.2 Installing an expansion card to riser card bracket 2
- 2.6.3 Installing an expansion card to riser card bracket 3
- 2.6.4 Installing an expansion card to riser card bracket 4
- 2.6.5 Installing an OCP 3.0 slot baseboard and OCP 3.0 card to the riser card bracket
- 2.6.6 Installing an ethernet expansion card to the riser card bracket
- 2.6.7 Installing GPU cards (on selected models)
- 2.6.8 Installing an ASUS PIKE II card
- 2.6.9 Installing M.2 (NGFF) cards
- 2.6.10 Configuring an expansion card
- 2.7 Cable connections
- 2.8 SATA/SAS backplane cabling
- 2.9 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 APM Configuration
- 5.5.4 Onboard LAN Configuration
- 5.5.5 Serial Port Console Redirection
- 5.5.6 CPU Configuration
- 5.5.7 PCI Subsystem Settings
- 5.5.8 USB Configuration
- 5.5.9 Network Stack Configuration
- 5.5.10 CSM Configuration
- 5.5.11 NVMe Configuration
- 5.5.12 SATA Configuration
- 5.5.13 AMD Mem Configuration Status
- 5.5.14 iSCSI Configuration
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
ASUS RS720A-E11-RS12E
1-23
Action PHASE POST CODE TYPE DESCRIPTION
PSP Boot
PSP Boot Loader
phase (Error Post
Codes)
0x20 error HMAC-SHA256/384 operation fail - internal status
0x21 error Booted from boot source not recognized by PSP
0x22 error PSP directory entry not found
0x23 error PSP failed to set the write enable latch
0x24 error PSP timed out because spirom took too long
0x25 error Cannot find BIOS directory
0x26 error SpiRom is not valid
0x27 error slave die has different security state from master
0x28 error SMI interface init failure
0x29 error SMI interface generic error
0x2A error invalid die ID executes MCM related function
0x2B error invalid MCM configuration table read from bootrom
0x2C error Valid boot mode wasn't detected
0x2D error NVStorage init failure
0x2E error NVStorage generic error
0x2F error MCM 'error' to indicate slave has more data to send
0x30 error MCM error if data size exceeds 32B
0x31 error Invalid client id for SVC MCM call
0x32 error MCM slave status register contains bad bits
0x33 error MCM call was made in a single die environment
0x34 error PSP secure mapped to invalid segment (should be 0x400_0000)
0x35 error No physical x86 cores were found on die
0x36 error Insufficient space for secure OS (range of free SRAM to SVC stack base)
0x37 error SYSHUB mapping memory target type is not supported
0x38 error Attempt to unmap permanently mapped TLB to PSP secure region
0x39 error Unable to map an SMN address to AXI space
(continued on the next page)