User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to riser card bracket 1
- 2.6.2 Installing an expansion card to riser card bracket 2
- 2.6.3 Installing an expansion card to riser card bracket 3
- 2.6.4 Installing an expansion card to riser card bracket 4
- 2.6.5 Installing an OCP 3.0 slot baseboard and OCP 3.0 card to the riser card bracket
- 2.6.6 Installing an ethernet expansion card to the riser card bracket
- 2.6.7 Installing GPU cards (on selected models)
- 2.6.8 Installing an ASUS PIKE II card
- 2.6.9 Installing M.2 (NGFF) cards
- 2.6.10 Configuring an expansion card
- 2.7 Cable connections
- 2.8 SATA/SAS backplane cabling
- 2.9 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 APM Configuration
- 5.5.4 Onboard LAN Configuration
- 5.5.5 Serial Port Console Redirection
- 5.5.6 CPU Configuration
- 5.5.7 PCI Subsystem Settings
- 5.5.8 USB Configuration
- 5.5.9 Network Stack Configuration
- 5.5.10 CSM Configuration
- 5.5.11 NVMe Configuration
- 5.5.12 SATA Configuration
- 5.5.13 AMD Mem Configuration Status
- 5.5.14 iSCSI Configuration
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-60
Chapter 5: BIOS Setup
The following items are configurable only when the OS Watchdog Timer is set to
[Enabled].
OS Wtd Timer Timeout [10 minutes]
Allows you to configure the length fo the OS Boot Watchdog Timer.
Configuration options: [5 minutes] [10 minutes] [15 minutes] [20 minutes]
OS Wtd Timer Policy [Reset]
This item allows you to configure the how the system should respond if the OS Boot
Watch Timer expires.
Configuration options: [Do Nothing] [Reset] [Power Down]
System Event Log
Allows you to change the SEL event log configuration.
Erase SEL [No]
Allows you to choose options for erasing SEL.
Configuration options: [No] [Yes, On next reset] [Yes, On every reset]
All values changed here do not take effect until computer is restarted.
View FRU Information
Press <Enter> to view FRU information.
No FRU information for fields indicate information needs to be filled by O.E.M.
BMC network configuration
The sub-items in this configuration allow you to configure the BMC network parameters.
Configure IPV4 support
DM_LAN1/Shared LAN
Configuration Address source [Previous State]
This item allows you to configure LAN channel parameters statistically or dynamically
(by BIOS or BMC). [Previous State] option will not modify any BMC network
parameters during BIOS phase.
Configuration options: [Previous State] [Static] [DynamicBmcDhcp]
The following items are available only when Configuration Address source is set to
[Static].
Station IP address
Allows you to set the station IP address.
Subnet mask
Allows you to set the subnet mask. We recommend that you use the same Subnet
Mask you have specified on the operating system network for the used network card.