User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to riser card bracket 1
- 2.6.2 Installing an expansion card to riser card bracket 2
- 2.6.3 Installing an expansion card to riser card bracket 3
- 2.6.4 Installing an expansion card to riser card bracket 4
- 2.6.5 Installing an OCP 3.0 slot baseboard and OCP 3.0 card to the riser card bracket
- 2.6.6 Installing an ethernet expansion card to the riser card bracket
- 2.6.7 Installing GPU cards (on selected models)
- 2.6.8 Installing an ASUS PIKE II card
- 2.6.9 Installing M.2 (NGFF) cards
- 2.6.10 Configuring an expansion card
- 2.7 Cable connections
- 2.8 SATA/SAS backplane cabling
- 2.9 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Ai Tweaker menu
- 5.5 Advanced menu
- 5.5.1 OffBoard SATA Controller Configuration
- 5.5.2 Trusted Computing
- 5.5.3 ACPI Settings
- 5.5.4 Redfish Host Interface Settings
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 SIO Common Setting
- 5.5.8 SIO Configuration
- 5.5.9 PCI Subsystem Settings
- 5.5.10 USB Configuration
- 5.5.11 Network Stack Configuration
- 5.5.12 CSM (Compatibility Support Module)
- 5.5.13 NVMe Configuration
- 5.5.14 APM Configuration
- 5.5.15 Third-party UEFI driver configurations
- 5.6 Platform Configuration menu
- 5.7 Socket Configuration menu
- 5.8 Event Logs menu
- 5.9 Server Mgmt menu
- 5.10 Security menu
- 5.11 Boot menu
- 5.12 Tool menu
- 5.13 Save & Exit menu
- Chapter 6: Driver Installation
- Appendix
5-27
ASUS RS720-E10-RS12
The following item appears only when SATA Controller is set to [Enable].
Configure SATA as [AHCI]
Allows you to identify the SATA port connected to Solid State Drive or Hard Disk Drive.
Configuration options: [AHCI] [RAID]
SATA Mode options
This submenu allows you to configure SATA mode related options.
SATA HDD Unlock [Enable]
If this item is set to [Enable], HDD password is enabled in the OS.
Configuration options: [Disable] [Enable]
SATA Led locate [Enable]
If this item is set to [Enable], LED/SGPIO hardware is attached.
Configuration options: [Disable] [Enable]
Support Aggressive Link Power Management [Enable]
Allows you to enable or disable SALP.
Configuration options: [Disable] [Enable]
SATA Port 0-7
Hot Plug [Disable]
Allows you to designate SATA port 0-7 as hot pluggable.
Configuration options: [Disable] [Enable]
PCH sSATA Configuration
sSATA Controller [Enable]
Allows you to enable or disable the sSATA Controller.
Configuration options: [Disable] [Enable]
The following item appears only when sSATA Controller is set to [Enable].
Configure sSATA as [AHCI]
Allows you to identify the SATA port connected to Solid State Drive or Hard Disk Drive.
Configuration options: [AHCI] [RAID]
sSATA Port 0-3
Hot Plug [Disable]
Allows you to designate sSATA port 0-5 as hot pluggable.
Configuration options: [Disable] [Enable]