ANTON By ESCAPE THE EVERYDAY INSTALLATION AND OWNER'S MANUAL — Shower Door Model Number: Please carefully read these instructions before you begin to install the products.
Before you start Thank you for purchasing your Aston shower door. We hope that it will provide you with years of satisfying use and enjoyment. Please read this manual carefully because it contains information and instructions about the proper installation of the unit. If you do not follow certain conditions of installation and maintenance, your warranty may be affected. 1. Inspect boxes for shipping damage.
Detailed Diagram of Shower Door Components Key Key Number Description QTY Number Description QTY 1 Door Stopper 2 13 Door Threshold End Cap 2 2 Top Rail 1 14 Door Handle 1 3 Fixed Glass 1 15 Door Seal 1 4 Sliding Door 1 16 Door Seal 1 5 Return Glass Panel 1 17 Door Seal 1 6 Rail End 1 18 Fixed Glass Bolt Assembly 2 7 Wall Mount 1 19 Screw Pack 1 1 8 Rail Mount Assembly 1 20 Screw Pack 2 1 9 Glass Clamp 4 21 Screw Pack 3 1 10 Sliding Door Track Divider 1 22 Screw Pack 4 1 11 Roller Assembly 4 23 Vertical cha
SUPPLIED HARDWARE /SCREW PACK | M4x40 P 4\ (1) Anchor m—— 4 M4x40 3 SCREW PACK e ) Anchor 4 M5x40 D 1 SCREW PACK M4x40 DAL 2 (3) Anchor = 2 SCREW PACK | M4x40 Anchor e 2 J SUPPLIED PARTS Model A — | 52" N | 56" , | 68" e} Model B 30" 7 , 32" 7 34" / 36" | [T 38" g
Installation Guide Please read and follow the installation instructions and guidelines in this section. Failure to follow the recommended instructions and installation techniques may lead to possible damage to the unit or the surrounding area. This can affect warranty claims. ATTENTION: This unit requires assembly. A minimum of two people are required for assembly, as several of the sections can be large and unstable until assembled.
Reverse Door opening This shower door can be assembled so that the sliding door opens from Left to Right, or Right to Left. The drawings below illustrate the shower door opening from Left to Right. Note the location of the fixed glass panel and return glass panel for the shower door opening from Left to Right. .
Measure the distance Install all of the wall material or materials you intend to use before installing the glass clamps and return glass panel, this includes all moisture resistant wall board or rock board, tile, stone or other wall covering. Refer to the drawing above and measure and mark the shower wall and floor for drilling locations to attach glass clamps and Vertical channel(23).
Installation of Vertical channel and glass clamps Using the appropriate drill bit for your wall and floor surface drill each hole location with a 5/16” diameter drill bit. Install the plastic wall anchors provided into the drilled holes NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size.
Installation of return glass panel Set properly check for level and plumb and then apply a small neat bead of 100% clear silicone to the inside bottom of the Vertical channel (23) . Install return glass panel (5) to Vertical channel (23) and glass clamp (9). Install U-channel Seal (24) to return glass panel (5).
Sliding Door Installation Measure the width of the shower opening at the top between the fixed glass and the wall. Note this is dimension "X". The following equation is used to determine the length to be cut from the rail in order to fit the shower opening. 3. Measure distance "Y" from the end of Top Rail (2) with per-assembled hardware mark the top rail. NOTE: Do not cut the end of top rail with per-assembled hardware. Only cut the end of top rail opposite the per-assembled hardware. 4.
Mark the Top Rail Location ATTENTION: A minimum of two people are required for the next assembly steps. Pr-assembly the top rail (2) onto the fixed glass (3) to locate the mounting points on the wall to your desired location. Painters tape or masking tape in the general location of the of the final installation will aid in marking the wall and floor.
Slide door stopper (1) onto end of top rail (2) See figure 1. The bumpers on door stopper (1) should be positioned on the top of top rail for final installation. Note: One door stopper comes per-assembled on top rail between fixed glass bolt assembly. See figure 1. Position the top rail (2) and fixed glass (3) as shown in figure 2 and connect fixed glass (3) to top rail (2) following the assembly sequence shown in figure 2.
NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size. 8. Using the appropriate drill bit for your floor surface drill hole locations with 5/16" diameter drill bit and install the plastic anchor from screw pack 2 into the drilled hole for glass clamp.
Installing Top Rail 4 Note: The set screw locations in rail end are not 17T Loosen set screws in rail end (6) and remove from top rail (2). See figure 1-1. Next remove wall mount (7) from rail end (6). Position wall mount (7) onto marked location on shower wall and mark pilot hole drilling location. See figure 1-2 NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size.
2. Using the appropriate drill bit for your wall surface drill the hole location with a 5/16" diameter drill bit. Install the plastic anchors from screw pack 2 into the drilled hole. See figure 2. 3. Attach the wall mount (7) to shower wall using M5 x 40 screw from screw pack 2. See figure 3. 4. Set properly check for level and plumb and then apply a small neat bead of 100% clear silicone to the inside bottom of the Vertical channel (23) .
12. Using the appropriate drill bit for your floor surface drill hole locations with 5/16" diameter drill bit and install the plastic anchors from screw pack 3 into the drilled hole. Position the sliding door track divider (10) over drilled holes on floor, and secure sliding door track divider (10) to floor using hardware in screw pack 3. See figure 11.
Install Wheel Rollers onto the Door Assemble the roller assemblies (11) onto sliding door (4) as shown in figure. Note: The door handle mounting holes should be positioned to left. The roller assemblies (11) will be on the outside of sliding door (4). The sliding door should be to the inside of shower area.
Hanging the Door ROLLER CAM ADJUSTMENT Rotate the outer edge of roller assembly using the small hex, while holding the large hex wrench in place. End View upper roller assembly top rail (2) = bottom roller g assembly =X Suspend the sliding door (4) on the top rail (2). Position the bottom edge of sliding glass door (4) into the groove of the sliding door track divider (10).
Install the Door Threshold The Door Threshold is used to prevent water from seeping out while bathing. Install the threshold according to these instructions. 1. Measure the distance between the fixed glass (3) and the shower wall. See figure 1. 2. Using a hacksaw cut the threshold bar (12) to fit distance measured between the fixed glass and shower wall. Remove any sharp edges or burrs after cutting threshold bar (12). See figure 2 3.
NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size. 4. Using the appropriate drill bit for your floor surface drill the hole locations with a 5/16" diameter drill bit. Install the plastic anchors from Screw pack 4 into the drilled holes. Repeat for the other side. See figure 4 5. Add a small amount of silicone sealant to bottom of threshold bar assembly place into position. See figure 5 6.
Installing the door handle Q Outside Inside @ ~— Install the door handle (14) using hardware provided. Follow the assembly sequence seen in drawing.
Final sealing Using Bath & Kitchen silicone sealant, seal the fixed glass (3) and returned glass panel (5) along bottom edge on shower base, and side edge along shower wall. Next seal around sliding door track divider (10).
Care and Maintenance As with any other luxury item, maintenance and care are critical to the long lasting quality and enjoyment of your shower door and tray. The proper care and maintenance outlined in this section are necessary to ensure the longevity of the unit. Damage caused by not following the care and maintenance guidelines in this section is not covered under the manufacturer's warranty.
ASTON GLOBAL INC. — Limited Warranty This warranty applies to products purchased from Aston Global Inc. after May 1, 2017. Aston Global Inc., a Texas Corporation ("Aston"), provides the following warranty coverage for shower doors and enclosures, bathtubs, shower panels and related components (The Products).
PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects. LABOR CHARGES AND/OR DAMAGE INCURRED DURING INSTALLATION, REPAIR, OR REPLACEMENT, AS WELL AS ANY OTHER KIND OF ANCILLARY COST, LOSS OR DAMAGE ARE EXCLUDED. COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial, commercial and business usage.
Aston product installations and repairs must be performed by either an Aston authorized agent or a licensed, insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty.
RESIDENTIAL INSTALLATIONS SHOWER DOORS and ENCLOSURES GLASS: Limited Lifetime Aston warrants the glass of shower doors, tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for the life of the product. Star Cast Protective Coating by Windshield: Ten (10) Years, provided by PCT Global LLC. For shower doors treated with Star Cast protective coating, warranty coverage is provided by its maker, PCT Global LLC.
DRAIN, OVERFLOW AND ACCESSORIES: Limited Lifetime Aston warrants the freestanding tub Drain, Overflow and Accessories in Polished Chrome and Brushed Stainless Steel finishes to be free from defects in workmanship and materials under normal residential use for two (2) years. The warranty for any part in Oil-rubbed Bronze finish shall be limited to one (1) year.
HARDWARE: One (1) Year Aston warrants shower door, tub door and shower enclosure hardware (i.e. handles, rollers, hinges, profiles, clips, guides, brackets, towel and support bars) to be free from defects in workmanship and materials under normal commercial use for one (1) year. SHOWER BASES: One (1) Year Aston warrants shower bases to be free from defects in workmanship and materials under normal commercial use for one (1) year.
SHOWER PANELS: One (1) Year Aston warrants shower panels to be free from defects in workmanship and materials under normal commercial use for a period of one (1) year from the initial date of purchase. STEAM SHOWERS: One (1) Year Aston warrants steam showers panels to be free from defects in workmanship and materials under normal commercial use for a period of one (1) year from the initial date of purchase.
ASTON SCARE THE EVERYDAY Customer Service 877-424-9699 Aston Global Inc 2805 Market Street, Suite 187 Garland, TX. 75041 If further assistance is needed, or you have a question, please visit our web site at: www.astonbath.
