Instructions for use Built-in unit CC4727S / 4000 CC4927S / 4000 CC41227S / 4000
EN Manual Pictograms used: Important information Tip EN 3 - EN 13
CONTENT Built-in unit Description 4 Introduction 4 Use Controls 5 Maintenance Cleaning 7 Removing the grease filters 8 Replacing the carbon filter 8 Changing the light bulbs 8 Installation General 9 Electrical connection 10 Mounting the built-in unit 11 Technical specification 12 Appendix Disposal of appliance and packaging 13 EN 3
YOUR BUILT-IN UNIT Description I A Switch fan on/off B C D E F G H I Reduce extractor capacity Increase extractor capacity Engage intensive mode Clean air function/filter indication Timer function Switch lighting on/off Dim lighting Display Introduction This user manual gives you a quick overview of all the possibilities offered by the appliance. You will find information on safety measures and maintaining the appliance. Please retain this user manual and the installation guide.
USE Controls I Switching the fan on and off • Switch the fan on with the on/off button (A) and select the desired extractor setting with buttons ‘B’ and ‘C’. The ‘I’ display indicates which setting has been selected. • Use button ‘D’ to switch on the intensive setting. “HI” appears in the ‘I’ display. After 6 minutes the intensive mode is automatically reduced to the setting previously selected. Switching the lighting on and off • Use the ‘G’ button to switch the lighting on and off.
USE Switching on the timer • Switch on the extractor hood with button ‘A’. • Set the extraction strength with buttons ‘B’ and ‘C’. • Press the Timer button ‘F’. The extractor hood switches off automatically after 30 minutes. Switch off the Timer function by pressing button ‘F’ again, or by switching off the extractor hood with button ‘A’. The display shows the selected speed and the remaining time. Grease filter indicator After 100 hours of use the “FF” indicator is shown in the display.
MAINTENANCE Cleaning Attention! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. The built in unit should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Do not use abrasive products.
MAINTENANCE Grease filters Removing the grease filters Switch off the electricity! Remove the plug from the socket or switch the electricity off at the mains. Open the panel and pull the special handle to remove the filter. Replacing the carbon filter The carbon filter must always be used if the built in unit is not ducted. 1. 2. 3. 4. Open the panel. Remove the grease filters. Fit the carbon filter by wedging it into the casing (D). Replace the filter grids in the extractor hood.
INSTALLATION General This appliance should be connected to the power supply by a recognized fitter who is familiar with, and works according to the correct safety regulations. This appliance meets the European requirements. Important that you know: • The minimum distance between the supporting surface for the cooking vessels on the gashob and the lowest part of the range hood must be not less than 65 cm. For use with an electric, ceramic or induction hob, this distance must be at least 55 cm.
INSTALLATION Electrical connection This appliance is manufactured in class I, it must therefore be connected to the earth system. Make sure the supply voltage ratings correspond with those stated on the appliance data plate. The connection to the mains is carried out as follows: BROWN = phase L BLUE = phase N YELLOW/GREEN = Earth During the electrical connection make sure that the electrical socket is equipped with earth connection. This canopy hood has been provided with a power plug.
INSTALLATION Installation • Open the panel. • Remove the grease filter. • Connect the controls together as depicted. • • First remove the 6 screws (2 on the left, 2 on the right, 2 on the front), followed by the frame. 0 13 744834 494- 26 • Use a saw to create a recess in the bottom side of the cupboard (at a distance of at least 650 mm from a gas hob). Refer to the measurement drawing for this. • Attach the unit with the 10 screws provided (12a). • Put the frame into position.
TECHNICAL SPECIFICATIONS Hood type Type / Approval Control type Width Supply (Voltage, frequency) Power Power motor Power lights (W) Level 1 Air flow, Noise, Pressure Level 2 Air flow, Noise, Pressure Level 3 Air flow, Noise, Pressure Level 4 Air flow, Noise, Pressure EN 12 CC4727S Built-in unit / G02-1M BRS ATB 2LED Electronic push buttons 77 CC4927S Built-in unit / G02-1M BRS ATB 2LED Electronic push buttons 86 CC41227S Built-in unit / G02-1M BRS ATB 2LED Electronic push buttons 116 220~240 V / 50 Hz 22
APPENDIX Disposal Disposal of appliance and packaging By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The local authorities can provide you with the relevant information. The packaging of this appliance is recyclable. It could have been made from: • cardboard; • polythene foil (PE); • CFK-free polystyrene (PS-hard foam).
EN 14
EN 15
562275 5622705/ VER 1 / 09-02-2016 562275
