Replacement Part List

ManualsBrandsArrow ManualsCanopiesBase Kit for 8 ft. x 8 ft., 10 ft. x 8 ft., 10 ft. x 9 ft. (Except: Swing Doors Units)

717070311

BASE KIT

Model No. FDN109

Owner's Manual & Assembly Instructions

PL01

NOTE: THIS KIT IS NOT SELF

SUPPORTING. SEE IMPORTANT

INSTRUCTIONS ON BACK COVER

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE

MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES

TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ

SAFETY INFORMATION PROVIDED IN THIS MANUAL

BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES

WHEN HANDLING METAL PARTS.

Summary of content (8 pages)

PAGE 1
Owner's Manual & Assembly Instructions PL01 BASE KIT Model No. FDN109 CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES WHEN HANDLING METAL PARTS. 717070311 NOTE: THIS KIT IS NOT SELF SUPPORTING.
PAGE 2
BEFORE YOU BEGIN.... PL02 1. Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. 2. Follow all directions and dimensions carefully. 3. Follow the step sequence carefully for successful results. 4. Be sure all the parts fit together properly before proceeding. 5. IMPORTANT: Remove Owner's Manual from main carton of your storage building and locate Interior Dimensions on the front cover. 6.
PAGE 3
How The Base Kit Works PK03 1. 2. 3. 4. Assemble Floor Frame. Assemble Base Kit. Attach Floor Frame assembly to Base Kit. Attach decking material inside Floor Frame assembly.
PAGE 4
● Parts Needed For ● Step 1 Front & Rear Channel Assemblies PL04 ● 9216 Front & Rear Channel (4) 1 Snap front & rear channels together as shown. Slide channels to match correct overall dimension shown. Bolt together where holes line up. Make two complete assemblies. (10 (10 x8 M O x9 120 MO DEL 1/1 DE ) 6" L) 305 ,0 c m 9216 ( 96 8x8 M 9/1 6" ODE 245 L) ,3 c m 9216 ● Parts Needed For ● Step 2 ● 9218 Side Channel (12) Side Channel Assemblies 2 Snap side channels together as shown.
PAGE 5
● Parts Needed For ● Step 3 ● F & R Channel Assemblies (2) ● Side Channel Assemblies (6) Fastening Channels PL05 3 Fasten two front & rear channels to two side channels using screws on the top flanges to form a rectangle. Attach the four remaining side channels at the dimensions shown, with flanges facing direction shown, using screws. 31 9/16" 80,2 cm 921 8 NOTE Ground must be level. Do not step on channels or angles until flooring material is in place.
PAGE 6
● Parts Needed For ● Step 4 ● 9215 Cross Channel (6) ● 9214 Cross Channel (4) ● 9715 Cross Channel (2) Fastening Cross Channels PL06 9214 9215 9215 9214 9215 9215 9214 9215 9215 9215 9214 9215 72 9715 (For ES109 ONLY) 9715 4 5/8" 11,7 cm (5 5/8" 14,3 cm for ES109 ONLY) FRONT (10x9 MODEL) 9715 Step 5 9214 ● Parts Needed For ● Fastening Corner Angles ● 0572 Corner Angle (4)) 5 Fasten corner angles to corners of unit at the 18" 45,7 cm dimension using screws.
PAGE 7
Attach Floor Frame Assembly PL07 6 Do not fasten decking material at this time! NOTE: FLOOR FRAME MUST BE LEVEL AND SQUARE BEFORE PROCEEDING! If you are using decking material, complete the floor frame assembly for the storage building as shown in the assembly instructions found in building carton. Position floor frame assembly on base kit, equal distance on the sides, front and rear.
PAGE 8
Finishing Materials PL08 Select one of the suggested finishing materials. Be sure Base Kit lies flat on the ground. To prepare the earth bed, remove sod and other organic debris, level the high spots with a flat shovel, and tamp the bed down. LAY EXTERIOR PLYWOOD OR ANY SUITABLE DECK MATERIAL (5/8" 15,5 MM MINIMUM THICKNESS) NOTE: Pressure Treated Lumber must not be used where it will make contact with your Arrow Products. The properties of Pressure Treated Lumber will cause accelerated corrosion.