01H 717740514 Owner’s Manual & Assembly Guide Gloves must be worn at all times to reduce risk of injury! * See Inside for Detailed Safety Information. COMMANDER™ SERIES MOUNTAINEER™ SERIES All Sizes Customer Service: 1-800-851-1085 or assist@arrowsheds.com BASE BUILDING DIMENSIONS Approx. † Size 10’ x 10’ 3,0 m x 3,1 m Storage Area 101 Sq. Ft. 697 Cu. Ft.
SAFETY PRECAUTIONS... 02H Safety precautions MUST be followed at all times throughout the construction of your building! Care must be taken when handling various pieces of your building since many contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. Practice caution with the tools being used in the assembly of this building. Be especially familiar with the operation of all power tools.
ASSEMBLY TIPS & TOOLS 03A Watch the Weather Closely: Be sure the day you choose to install your building is dry and calm. Do NOT attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Use Teamwork: Two or more people are required to assemble your building. One person can hold the parts or panels in place while the other person fastens them together and handles the tools. This makes the process of assembling your building faster and safer.
BEFORE YOU BEGIN... 04H Your Commander™ / Mountaineer™ Shed has a Modular Design. This means your shed can be extended to virtually any length with the addition of Extension Modules. Extension Modules can be installed when you first construct your building, or they can be added to it later. How you assemble your building will depend upon how many Extension Modules you have purchased. See below to see how many Modules are included in your building. How your building was shipped.
CONSTRUCTING A BASE... 05H Before you assemble your building, you must construct a base. The length of your base, shown as “L” in the diagrams below, will depend on the length of your building. See below.
HARDWARE - C1GA C1GA Hardware Key Part Part No. No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 65103 65923 65004 66611 66625 66783 65106 65943 66646 67468 66609 66778 66183L/R 66781 67545B 6228 Qty.
HARDWARE - C2GA / GA5M C2GA Hardware *Packed loose in carton Key Part Part Qty. No. No. Description List 1 10651 Latch Plate * 3 8 2 7003 Shear Plate LT * 8 3 7004 Shear Plate RT * 1 4 66779 Slide Bolt * 2 5 66780 Cane Bolt * 2 6 66782 Door Handle * GA5M Hardware Key Part Part No. No. Description 2 3 7 8 9 10 11 12 7003 7004 65103 65923 65004 66611 66646 67293B Qty.
7743 7822 8576 8577 8578 8579 10618 10619 10620 10621 10622 80017 80037 6635 9009 9204 10625 10627 10628 10629 10630 10631 10632 10633 10634 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 C1GA C1GA C1GA C1GA C1GA C1GA C1GA C1GA C1GA C1GA C1GA C1GA C1GA C2GA C2GA C2GA C2GA C2GA C2GA C2GA C2GA C2GA C2GA C2GA C2GA Part No. Key Carton No. No.
13 7 8 28 SNAP Bend to separate. 10627 2 18 37 19 18 19 26 18 10627 Part 10627 Front Wall Channel (No. 18) may be joined in pairs. 38 2 9 23 16 1 7 38 25 28 34 35 31/32 17 3 10 35 2 15 27 29 4 11 24 34 17 2 14 5 1 Part No. 30 (Truss Post Insert) fits inside Part No. 29 (Truss Post) and is not shown below.
Door Panel (Hinge) Right Door Panel Left Door Panel Horizontal Door Brace Vertical Door Brace (Latch) Vertical Door Brace (Hinge) Top Door Trim Door Astragal Door Diagonal Brace Vertical Door Brace Cane Bolt Bracket 2 1 1 4 2 2 2 2 8 4 2 12 13 14 15 16 17 18 19 20 21 22 23 24 25 GA5M GA5M GA5M GA5M GA5M GA5M GA5M GA5M GA5M GA5M GA5M GA5M GA5M GA5M 10623 10624 80051 10635 10678 10637 10647 10648 10626 10636 10675 C1GA C1GA C1GA C1GA C1GA C1GA C1GA C1GA C2GA C2GA C2GA 7822 7743 6015 10680 10625 10632 10
6 1 7 8 3 8 10 9 11 5 2 7 4 1 Right Door 4 5 4 Left Door 9 6 4 10 10 9 11 9 9 10 9 9 9 11 12 18 12 17 16 19 14 13 20 25 23 17 18 16 19 22 12 24 13 12 22 13 23 15 25 20 Part No. 21 (Truss Post Insert) fits inside Part No. 20 (Truss Post) and is not shown above.
Step 1: Trusses You will need for this page: LS SB (QTY: 12) (QTY: 24) 10641 2 10642 2 Truss Post Truss Post Insert 12H 10643 2 Upper Chord Truss 10644 2 Lower Chord Truss 7003 4 Left Shear Plate 7004 Washers are to be used on painted parts only. Washers are not necessary on unpainted parts and there are not enough to use on every Screw and Bolt. 4 Right Shear Plate Align the bottoms of the Truss Post and Truss Post Insert and join as shown.
Step 1: Continued You will need for this page: LS 10645 1 SB (QTY: 12) Truss Splice (QTY: 14) SB Knee Brace 6 10642 Attach Knee Braces to Truss using Large Screws as shown. Do not tighten at this time. With the Truss assembled, check that the width of the Truss is 118 1/4” (300,4 cm) across the top and bottom of the Truss. If so, tighten all fasteners. Repeat steps to build additional Trusses.
Step 2: Rear Wall You will need for this page: LS SB (QTY: 8) (QTY: 15) 10629 4 14H 10630 2 10631 2 10640 3 Rear Wall Channel Rear Wall Diagonal Wall Post Rear Frame If you purchased a Door Kit, skip this page and move on to page 16. 1 Lay out the parts and position them as shown. Overlap the Rear Frames by 4” (10,2 cm) and connect them to the Wall Post in the center of the Rear Wall using Small Bolts and Nuts as shown. Do not tighten at this time.
Step 2: Continued You will need for this page: SS 7822 Wall Panel (QTY: 30) 2 15H 10619 2 Corner Panel 10619 10619 INSIDE SS 7822 7822 10619 SS SS 7822 10630 SS 7822 LEAVE HOLES OPEN ALONG SIDE OF WALL SS OUTSIDE Place Washers on all Bolts and Screws used on painted parts. This will help to prevent leaks and corrosion. SS Using Small Screws, attach a Wall Panel and Corner Panel to each corner of the Rear Wall as shown.
Step 3: Front Wall You will need for this page: LS SB (QTY: 34) (QTY: 24) 10640 2 10652 2 10627 6 10628 4 Wall Post Wall Post (Hinge) Front Wall Channel Front Wall Diagonal If you purchased a Door Kit, build two Front Walls. 10673 2 Front Frame 10638 1 Long Fascia Left Front Wall Assembly 10640 16H 10639 1 Short Fascia Right Front Wall Assembly 10652 10652 10627 10640 SB SB SB LS SB LS 10628 10628 LS 10627 SB LS SB LS SB SB Lay out the parts and position them as shown.
Step 3: Continued You will need for this page: SB SS SB Front Wall Panel (QTY: 12) (QTY: 8) SB 10618 2 SB SB SB SB SB SB 10619 2 17H Assemblies from previous page: • • • Corner Panel Left Front Wall Assembly Right Front Wall Assembly Door Header Assembly Slide the Door Header Assembly down onto the Front Wall Assemblies as shown and secure with Small Bolts and Nuts. Once these pieces are joined, take care when moving them as the Door Header may bend.
Step 4: Truss Installation You will need for this page: LS SB (QTY: 8) (QTY: 4) 10632 4 10634 2 Assemblies from Step 1: • Side Wall Channel Side Frame 18H 10632 Truss Assemblies (2) Overlap Length SB 10632 8 1/4” 21,0 cm SB SB SB 10632 Assemble two sets of Side Frames by overlapping them by 8 1/4” (21,0 cm) and inserting two Small Bolts and Nuts as shown above. These will form the left and right Floor Frames. 1 10632 Notched side of Frame must face inside building.
Step 4: Continued You will need for this page: SB Side of Beams with small holes must face up. 10650 4 Outer Roof Beam (QTY: 14 ) 19H Main Outer End View of Double Beam 10650 Outer 10650 Main Roof Beam Main Outer 10650 10650 10650 Remove Bolts holding Truss peaks together (from Step 1-6). Next, place two Middle Roof Beams back-to-back and secure with two Small Bolts and Nuts as shown above. This is the Main Roof Beam.
Step 4: 20H Continued for Extension Modules You will need for this page: LS SB (QTY: 6+) (QTY: 18+) 10632 2+ Side Frame 10634 2+ Side Wall Channel 10650 4+ Assemblies from Step 1: • Roof Beam All remaining Truss Assemblies If you are erecting a 10’x10’ (3,0 m x 3,1 m) building, skip this page and move on to page 21. All Truss Sections are assembled in the same manner as the Truss Section just erected. Install one additional Side Frame per side for each additional Module.
Step 5: Rear Wall Install You will need for this page: LS (QTY: 2) LS (QTY: 4) 10633 2 21H Assemblies from Step 2: Side Wall Channel • Rear Wall Assembly If you purchased a Door Kit, skip this page and move on to page 22. 10633 10633 10’x10’ (3,0 m x 3,1 m) building shown. Carefully position the Rear Wall Assembly in place at the rear of the building and secure to Side Frame with one Large Screw per side as shown.
Step 6: Front Wall Install You will need for this page: LS LS (QTY: 2) (QTY: 4) 10633 2 10622 1 80037 1 Side Wall Channel Right Door Jamb Left Door Jamb Assemblies from Step 3: • Front Wall Assembly SS If you purchased a Door Kit, install second Front Wall Assembly on the rear of the building. (QTY: 6) 10’x10’ (3,0 m x 3,1 m) building shown.
Step 7: Wall Angles You will need for this page: LS SB (QTY: 4+) 1 (QTY: 4+) 10625 4+ LS (QTY: 4) 23H 10625 LS Side Angle Starting at the front and rear of the building, attach Side Wall Angles to the front and rear wall of the building with Large Screws as shown. SB LS SB LS 10625 10’x10’ (3,0 m x 3,1 m) building shown. LS All angles overlap by 8 1/4” (21,0 cm) Overlap Length Next, insert Large Screws where the Wall Angles meet the Trusses.
Step 8: Wall Panels 24H IMPORTANT: At this time, take a moment to ensure the building is level and square. Measure diagonally across the building from opposite corners; when these measurements match, the building is square. For the remainder of assembly it will be important that the building is both level and square. Whenever a crimped rib and an uncrimped rib meet, the crimped rib should be placed UNDER the uncrimped rib if possible. See next page.
Step 8: Continued You will need for this page: SS 7822 10+ SB (QTY: 150+) (QTY: 9+) Wall Panel 10’x10’ (3,0 m x 3,1 m) building shown. Working one side at a time, lift the Panels into place and secure with three Small Screws in the top of the Panel, three Small Screws in the middle of the Panel, and three Small Screws in the bottom of the Panel. Roll the Panel back as shown on the previous page and overlap the rib with the rib of the next Panel.
Step 9: Gables You will need for this page: SB (QTY: 8) 8577 2 Left Gable 8576 2 Right Gable 26H 6635 4 Bracket 69835 4 Edge Trim GABLES ARE STACKED TOGETHER DURING SHIPPING AND MAY BE MISTAKEN FOR ONE GABLE! SEPARATE GABLES BEFORE CONTINUING. Edge Trim (Plastic) 69835 Edge Trim MUST cover Gable edge. Install Edge Trim to cover Gable Edge BEFORE doing ANY work with Gables. Failure to do so could result in injury.
Step 9: Continued You will need for this page: SS (QTY: 16) 9009 SB (QTY: 2) 1 27H 6228 2 Gable Brace Track Sup. Gable must fit UNDER Side Wall Angle at corner. 8576 SS 8577 Working with one Gable at a time, attach the Gables to the top Rear Frame with Small Screws. The Gable should be attached using the row of holes closest to the outside of the building. Do not insert screws into the two holes closest to where the Gables join. These will be used to attach the Track Support later.
Step 9: Continued You will need for this page: SB (QTY: 13) Leave Hole Open 10649 10649 4 28H 10649 10649 Roof Beam 10649 10’x10’ (3,0 m x 3,1 m) building shown. 10649 5 6 Top View of Gables Seal the gap between the Gables using the Weather Stripping Tape as shown. Secure two Front and Rear Roof Beams together with a single Bolt to form the Main Roof Beam as shown above. The end of the Main Roof Beam with the open hole should face the Gable. Tape should wrap around gap between Gables.
Step 9: Continued You will need for this page: 9204 29H 1 SB (QTY: 2) 9204 Beam Brace 10’x10’ (3,0 m x 3,1 m) building shown. 8 Attach the Roof Beam Brace to the Track Support with one Small Bolt and Nut as shown. Tab end attaches to Roof Beam. Rotate to align with Roof Beam and secure to Roof Beam with one Small Bolt and Nut as shown. Repeat Steps 9-2 thru 9-9 to install Gables at the front of the building.
Roof Install Prep Page 30H Read thru all of Roof Assembly before beginning Step 10. IMPORTANT: At this time, take a moment to ensure the building is level and square. Measure the building diagonally again to make sure the building is square. The building should be square at the base and at the top. This will make Roof Panels fit better and holes will better align. Be sure to carefully follow the Roof Panel Placement Order Diagram on this page.
Step 10: End Panels You will need for this page: SS 8578 2 31H 8579 2 SB (QTY: 8) Right End (QTY: 24) Secure the End Panel to the Main Roof Beam by placing a Small Screw in hole #1 (from the diagram below). Carefully remove the Gable Edge Trim once the Panel is in position. 1 2 Fasten Panel to Gable by placing Small Bolts and Nuts through holes #2 - #7. Fasten the holes in order. 3 Secure the Panel to the outer Roof Beam by placing a Small Screw in hole #8. Repeat for other three End Panels.
Roof Assembly Chart 10’x10’ (3,0 m x 3,1 m) R EP RP RP RP RC - F/R 10’x20’ (3,0 m x 6,1 m) EP RP RP RP RP EP 10’x25’ (3,0 m x 7,5 m) EP EP 10’x30’ (3,0 m x 9,0 m) RP RP EP EP EP RP RP M RP RP RP RP RP RC - F/R RP RP RC - MID RP RP RC - MID RP RP R M M RP RP RP RP RC - MID RP RP L RP M RP EP M M RP NOTE: The symbol indicates a 2” (5,1 cm) strip of Weather Stripping Tape.
Step 11: Roof Assembly You will need for this page: SS 7743 6 SB (QTY: 48) (QTY: 8) Roof Panel Begin weather stripping the roof ridge. Apply more of the Weather Stripping after each additional Panel is installed. A strip of Weather Stripping Tape 2” (5,1 cm) long should be applied over each Bolt that is on a rib overlap and under the Ridge Cap. 1 Attach the first four Panels (#5 - #8) in the order given in the diagram on page 30. Use the Roof Panel Diagram on page 30 while assembling the roof.
Step 11: Continued For 10’x10’ (3,0 m x 3,1 m) ONLY. 5 DO NOT fully tighten Ridge Cap Bolts until you have both Ridge Cap Bolts in place. This will ease assembly. Bolts must be fully tightened before moving on to the next page. Overlap two Front and Rear Ridge Caps as shown and secure with two Small Bolts and Nuts. SB 34H End of Ridge Cap with four holes must face toward the outside of the building. Do not secure at this time.
Step 11: 35H Continued for Extension Modules You will need for this page: SS SB (QTY: 32+) (QTY: 8+) 7743 4+ 10621 1 Ridge Cap FR Roof Panel 10680 0+ Ridge Cap Mid Continue to apply Weather Stripping. 6 7 8 9 If you are erecting a 10’x10’ (3,0 m x 3,1 m) building, skip this page and move on to page 36. Install two more Roof Panels. Continue to apply Weather Stripping Tape as you go. DO NOT fully tighten Ridge Cap Bolts until you have both Ridge Cap Bolts in place. This will ease assembly.
Step 11: Continued You will need for this page: SS SB (QTY: 52+) (QTY: 6) 36H 7743 2 Roof Panel Continue to apply Weather Stripping. At this point there should be only two Roof Panels remaining. Install last two Roof Panels. Because the last Ridge Cap is already in place and has been secured at one end, you may need to move the Ridge Cap slightly to secure the last two Panels to the Main Roof Beams.
Step 12: Roof Trim You will need for this page: SS (QTY: 4) 1 SS SB (QTY: 16+) (QTY: 8) 80017 2 Left Trim 37H 10620 2 6015 0+ Right Trim Mid Trim 2 Trim Cap (L) 2 Slide Peak Cap legs under Ridge Cap and secure Ridge Cap ends with four Small Bolts and Nuts on each end as shown. Trim Cap (R) 2 Peak Cap Position Left and Right Roof Trim as shown below and secure with Small Screws. Do not fasten the last Screw on each end.
Step 13: Door Assembly You will need for this page: SB (QTY: 10) 10623 2 10624 1 80051 1 Door Panel (Hinge) Right Door Panel Left Door Panel If you purchased a Door Kit, repeat Door Assembly process for rear of building. Refer to page 11 for Door assembly overview. 1 Position Door Panels as shown and secure using Small Bolts and Nuts. NOTE: Door Panels in the image below are shown pictured from the inside of the building. Pay close attention to how Panels are positioned.
Step 13: Door Assembly You will need for this page: 10635 4 [ NO HARDWARE NEEDED FOR THIS STEP ] 10637 2 10678 2 Vert. Door Brace (Hinge) Vert. Door Brace (Latch) 10635 Horiz. Door Brace Extra hole along INSIDE of Door. 2 Position Horizontal Door Braces, and Vertical Door Brace (Hinge) and Vertical Door Brace (Latch) as shown. NOTE: Doors in the image below are shown pictured from the inside of the building. Pay close attention to how parts are positioned.
Step 13: Continued You will need for this page: LS (QTY: 12) 40H 10636 4 Vert. Door Brace Open ends of Vertical Door Braces must face edge of Doors. Slide Vertical Door Braces into position with ends inside Horizontal Door Braces. Double check that the open ends of the Vertical Door Braces face the edges of the Door (see image to right) and secure with Large Screws in each Door. NOTE: Doors are shown pictured from inside building.
Step 13: Continued You will need for this page: Plastic Washer LS LNB SB (QTY: 13) (QTY: 2) (QTY: 2) (QTY: 3) A 41H 10651 1 66781 1 Latch Plate Spring Latch 10626 8 Diagonal Brace A: Position parts as shown and secure to upper inside corner of left Door with Large Screws. Spring Latch attaches to Latch Plate using Small Bolts and Nuts. Place three Plastic Washers behind top hole of Spring Latch as shown; this will help alignment.
Step 13: Continued You will need for this page: LS (QTY: 26) 10675 2 66780 2 Cane Bolt Bracket Cane Bolt 5 Secure all Diagonal Braces to the Vertical Door Braces with Large Screws as shown. Next, position the Cane Bolt Bracket backto-back against the Vertical Door Brace closest to the center of one Door as shown. Slide the Cane Bolt Bracket to the bottom of the Door and secure with three Large Screws. Repeat for other Door.
Step 13: Continued You will need for this page: LS LS (QTY: 20) LB (QTY: 20) (QTY: 2) 10648 2 Astragal Top Trim 7 Secure the Horizontal Door Brace to the Door with Large Screws. Position Door Trim and Astragals as shown and secure with Large Screws. Lock Eyelet slides thru Astragal on right Door and is secured with two Large Bolts and Square Nuts. Pay close attention to the position of each part. Left Door 10647 2 43H 66778 1 Lock Eyelet If holes do not align, insert Screw at an angle.
Step 13: Continued You will need for this page: LB (QTY: 8) LB (QTY: 4) 66782 2 Door Handle 8 Slide Latch Plate into position on the Left Door. Next, position the Slide Bolt on the face of the Door and secure with Large Bolts and two Square Nuts on each Bolt. Position the Door Handle on the face of the Left Door and secure with Large Bolts and Square Nuts. This completes the Left Door assembly.
Step 13: Continued Slide Bolt may need adjustment to align properly. You will need: 45H If Slide Bolt does not align properly, you may need to insert plastic washers between the door and the Slide Bolt to ensure proper fit. Adjust number of plastic washers until desired fit is reached. 66609 6 FS (QTY: 36) Hinge Hanging the Doors: FS FS After the Doors have been assembled, install hinges on one Door using flathead Screws and Nuts. Use the image to the left as a guide to proper hinge position.
ANCHORING OPTIONS... 46H IMPORTANT: • • • • Doors must hang and swing level before anchoring building. Anchor your building at this time. See below for details on anchoring. After anchoring, drill a 5/8” (1,6 cm) hole at least 2” (5,1 cm) into your base to receive the left-side Cane Bolt and hold the Door (left side only) closed. Please take a moment to ensure that the building is installed in accordance with these instructions and with all applicable regulations.
CARE & MAINTENANCE... 44A Exterior Care: For a long lasting finish, clean and wax the exterior surface. We recommend washing with a mild soap solution. DO NOT use power washing to clean your shed. Using a spray automotive type wax periodically on the exterior is highly recommended if you are in a high humidity or coastal climate region. Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible storage.
ARROW ACCESSORIES... ANCHOR KITS ATTIC KIT / WORKBENCH KIT Anchor Kit contains heavy-duty steel augers, 60' (18 m) of steel cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground. For buildings larger than 10'x9' (3,0 m x 2,6 m), use 2 kits. Heavy-duty galvanized steel bars that fit all 10' (3,0 m) wide Arrow buildings.
