ARMORTALLIC METALLIC EPOXY COATING KIT APPLICATION INSTRUCTIONS READ INSTRUCTIONS CAREFULLY BEFORE MIXING AND APPLYING Issues with your order? Please contact ArmorPoxy for assistance: www.armorpoxy.com Table of Contents APPLICATION NOTES BEFORE YOU START KIT CONTENTS PRODUCT APPLICATION STEPS 1. REMOVE FOREIGN SUBSTANCES 2. PRESSURE WASH AND ETCH 2 4 5 6 6 6 A. Alternate Prep (Floor Grinding) 1. Step One 2. Step Two 6 6 7 3. TAPE PERIMETER 4. FLOOR REPAIRS 5. FIRST LAYER: EPOXY PRIMER 6.
APPLICATION NOTES ArmorPoxy’s ArmorTallic Epoxy Coating Kit should be applied between 50-90°F and when relative humidity is 80% or less. If cooler, add portable electric (not kerosene) heaters to the area to keep air temperatures higher. Material should be stored in a dry area at temperatures between 50-90°F. Do not store in warm/hot areas prior to use, as cooler material has a longer working time. Material must be above 60°F for installation. Install in areas with proper ventilation.
INSTALLATION CHART DAY 1 INSTALLATION TIMELINE DRY TIMES APPLICATION TEMPERATURE PREP FLOOR DAY 2 DAY 3 PRIME METALLIC EPOXY COAT ACID ETCH.
BEFORE YOU START ● ● ● ● SUPPLIES You need to supply the following items: standard 9” roller frame, painting extension pole, and power drill as these items are not included in the kit. Other suggested items are measuring cups, roller tray (for the topcoat), a plastic or cloth drop cloth to mix on and xylene or similar cleaner and rags for cleaning hands or drips. ETCH ArmorPoxy’s Etch is a mild, powdered citric-based cleaning agent.
KIT CONTENTS *Image above represents 600 SQ FT kit. Any smaller kit will come with less coating product. Please note Metallic Pigment Color choice is 1 color per 600 square foot kit. Additional pigment colors can be purchased separately and used in conjunction with this kit to create unique and customized designs. Please contact your sales representative for more information and pricing.
PRODUCT APPLICATION STEPS 1. REMOVE FOREIGN SUBSTANCES Remove foreign substances. Scrape off any surface debris such as putty, paint, oil or dirt so that the surface is smooth and even. Use running water from a hose with nozzle, or a pressure washer to flush the entire area to remove any loose dirt and debris from the surface. For oil stained areas, use an oil degreaser to help clean the area before proceeding. ℹ️ Hint.
note that standard wood sandpaper or tools do not work properly on concrete. You can also re-etch these areas with acid etch at a higher concentration to achieve desired results. ℹ️Hint: When sanding by hand, use a drywall sanding pad and extension pole to simplify the process. 2. Step Two After sanding and brushing with a wire brush, rinse the areas involved to remove all dust and foreign materials. Then proceed with the cleaning and degreasing process described above.
6. SECOND LAYER: METALLIC EPOXY A. MIXING AND FIELD TINTING 1. Add the proper quantity of metallic pigment to all of your Part A’s accordingly. Our kits come with 1 standard metallic pigment color but more can be purchased and used to create unique and custom looks. Mix in all of the pigment thoroughly. This step gives you an even Part A to work with. IF YOU PLAN ON USING TWO COLORS OF METALLIC PIGMENT.
ℹ️ Hint: Coverage of 100% Solids Epoxy: When applied to a smooth/dry surface, coverage is approximately 300 sq.ft per 3 gallon kit of 100% solids epoxy. Coverage calculated @ 25-30 mils thickness. This is equivalent to 4 layers of standard floor paint. Topcoating adds an additional layer of protection and thickness. B. PRODUCT APPLICATION 1. Pour the epoxy on the floor in a ribbon left to right. Have your flat squeegee ready to go and spread it out evenly.
Please note that if you notice any uneven or problem areas with your application, do not apply the topcoat until you have rectified those issues. Normally topcoat will not ‘fix’ issues with the epoxy application. 8. CLEAN UP ArmorTallic epoxy can be cleaned off hands and other surfaces with xylene (xylol) or similar solvent cleaners before the material begins to harden. Warm soap and water may also be used if the epoxy is still wet. Sticky resin on hands can be removed with mineral spirits or xylene.
FREQUENTLY ASKED QUESTIONS My concrete is relatively new, do I still need to clean the floor before applying ArmorPoxy? ● Yes, construction dust, drywall paste, and paint splatters can affect the bond. Lime, which is an ingredient of concrete, floats to the top while it cures and must be treated. Scrape foreign substances from the floor and then clean the floor with the etching solution. This is a mandatory step. Skipping the prep step can cause failures.
ARMOR NO PREP PRIMER INSTRUCTIONS DESCRIPTION Armor No Prep Primer is a 1-Part nano coating that can be used to prime surfaces that are already coated and removing the coating by mechanical means will be too laborious or the environment does not allow for it. Armor No Prep Primer can be used IN ADDITION to the ArmoTallic Metallic Coating Kit as the first primer layer coat. Below are detailed instructions should you purchase the Armor No Prep Primer.
Before use, read Preparation, Hazard and Precautionary Statements. ALWAYS TEST using the equipment and procedures prior to starting the job. TYPICAL COVERAGE RATES (SQUARE/FEET) Smooth Concrete 500-600 | Concrete Block 200-250 | Broom Finish 250-300 | Concrete Pavers 250-300 Diamond Grind 150-250 | Concrete Slab 250-300 Coverage rates will vary based on substrate porosity and application method HORIZONTAL SURFACES Ensure surface is free of any dust, debris and other contaminants.
