TH 721 D22 B/LPG TH 721 D22 B/NG TH 721 D22 B/TG TH 731 D2/A B/LPG TH 731 D2/A B/NG TH 731 D2/A B/TG TH 931 D2/A B/LPG TH 931 D2/A B/NG TH 931 D2/A B/TG TH 721 D22 E/LPG TH 721 D22 E/NG TH 721 D22 E/TG TH 731 D2/A E/LPG TH 731 D2/A E/NG TH 731 D2/A E/TG TH 931 D2/A E/LPG TH 931 D2/A E/NG TH 931 D2/A E/TG 1
Table of Contents For your safety Warnings The appliance Description of the appliance Installation Start-up and Use Precautions and tips General safety Assistant Cleaning and maintenance Practical tips FAQs and Trouble shooting Electrical connection Pg2 Pg2 Pg3 Pg3-5 Pg6-12 Pg13-14 Pg14 Pg14 Pg15 Pg15 Pg16 Pg17 Pg18 1
For your safety These instructions have been drawn up for your safety and that of others. You are therefore requested to read them carefully before installing and using the appliance. Keep this instruction manual for future reference as necessary. If the appliance is sold or moved, make sure that the manual is handed over to the new user. WARNINGS WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
THE APPLIANCE TH 721 D22 B/LPG TH 731 D2/A B/LPG TH 721 D22 B/NG TH 731 D2/A B/NG TH 721 D22 B/TG TH 731 D2/A B/TG TH 721 D22 E/LPG TH 731 D2/A E/LPG TH 721 D22 E/NG TH 731 D2/A E/NG TH 721 D22 E/TG TH 731 D2/A E/TG TH 931 D2/A B/LPG TH 931 D2/A E/LPG TH 931 D2/A B/NG TH 931 D2/A E/NG TH 931 D2/A B/TG TH 931 D2/A E/TG DESCRIPTION OF THE APPLIANCE 1. 2. 3. 4. 5. 6.
The Gas cooktop, which can be used built-in, are supplied with two or three burners with glass panel.Please refer to the table below for the detail of wok burner. All of the burners are manufactured by HORISUN. Each burner, which is operated by a FSD/plug type gas valve, is controlled by metal control knobs positioned on the front of the panel, Each burner incorporates a flame supervision device(Thermo couple).The appliance incorporated a battery supply of 1.
Burner Variants Model number Wok Semi-rapid burner burner TH 721 D22 B/NG 2 TH 731 D2/A B/NG Total Dimensions 0 9kW (760 X 450)mm 2 1 10.7kW (760 X 450)mm TH 931 D2/A B/NG 2 1 10.7kW (860 X 500)mm TH 721 D22 E/NG 2 0 9kW (760 X 450)mm TH 731 D2/A E/NG 2 1 10.7kW (760 X 450)mm TH 931 D2/A E/NG 2 1 10.7kW (860 X 500)mm Note: Wok burner = Rated at 4.5kW Auxiliary burner = Rated at 1.7kW Injector Injector Full rate size(mm) marking kW Inner ring 0.
Installation Instructions for Built-In The following instructions are intended for the installer so that the installation and maintenance procedures may be followed in the most professional and expert manner possible. Positioning This appliance may only be installed and operated in permanently ventilated rooms in compliance with provisions laid down by current regulations and standards.
B）The room must also allow for the influx of the air needed for proper combustion. The flow of air for combustion purposes must not be less than 2 m3/h per kW of installed capacity. The supply of said air can be effected by means of direct influx from the outside through a duct with a inner cross section of at least 100 cm2 which must not be able to be accidentally blocked.
Installation of Built-In cooktops The appliance can be installed next to furniture units which are no taller than the top of the cooker. The wall in direct contact with the back panel of the cooker must be made of non-flammable material. During operation the back panel of the cooker could reach a temperature of 500C above room temperature.
The dimensions of the cutout for the appliance must be those indicated in the figure D. Clamps are provided to fasten the cooktop to counters measuring from 20 to 60 mm in thickness. To fasten the cooktop securely, it is recommended that all the clamps be used.
The cooktop can also be installed above built-in ovens provided with cooling ventilation. In the event the cooktop is installed above a built-in oven, a wood panel must be inserted as insulation. This panel must be placed at about 50 mm from the bottom of the cooktop itself. Important: When installing the cooktop above a built-in oven, the oven should be placed on two wooden strips; in the case of a joining cabinet surface, remember to leave a space of at least 45 x 560 mm at the back.
Gas Connection for Cooktop The cooktop should be connected to the gas supply by an authorized installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas tanks must be carried out according to the safety standards currently in force, and only after it is ascertained that it is suitable for the type of gas to be used.
Check the Seal Once the appliance have been installed, make sure all the connections are properly sealed, using a soapy water solution. Never use a flame. a) Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible b) The adjustment conditions for this appliance are stated on the label (or data plate) c) This appliance is not connected to a combustion products evacuation device.
Step 1 - Remove the outer cap Step 2 - Remove the inner cap Step 3 - Remove the burner Step 4 - Place the burner back ensuring the thermocouple and igniter (Circled) are fitted to the appropriate slots in the burner Step 5 - Please follow the steps below a. Place the inner cap so that it fits properly b. Place the outer cap ensuring that the arrow in the burner aligns with the yellow mark indicated or slot on the outer cap (Highlighted) c.
START UP AND USE The position of the corresponding gas burner is indicated on each control knob. Gas Burners The burners differ in size and power. Choose the most appropriate one for the diameter of the cookware being used. The burner can be regulated with the corresponding control knob by using one of the following settings: Symbol description To turn on one of the burner, please press the corresponding knob all the way in and turn in the counter-clockwise direction to the “high” setting.
PRECAUTIONS AND TIPS General safety This appliance has been designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully. Call only the Service Centers authorized by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. This Manual is for a class 3 built-in or or class 2 built with oven beneath.
It is recommended that you follow the guidelines below: Only use the appliance to cook food, avoiding all other uses. Check the condition of the appliance after it has been unpacked. When not in use, take out the battery and turn off the gas valve (if present).
Greasing the Taps The taps may jam in time or they may become difficult to turn. If so, the tap itself must be replaced. N.B.: This operation must be performed by a technician authorized by the manufacturer. PRACTICAL TIPS Using the Burners For best performance, follow these general guidelines: 1. Use the appropriate cookware for each burner (see table) in order to prevent the flame from reaching the sides of the pot or pan; 2. Always use cookware with a flat bottom and keep the lid on; 3.
FAQ and TROBULE SHOOTING It may occur that the cooktop does not function or does not function properly. Before calling customer service for assistance, check with below. First of all, check to see that there are no interruptions in the gas and battery supplies, and, in particular, that the gas valves for the mains are open. FAQs The burner does Possible Reasons Burner Solutions The gas holes on the The gas holes on the not light or the burner are clogged. burner are not clogged.
FAQ and TROBULE SHOOTING FAQs The burner has wobbled and not Possible Reasons Burner not aligned properly leading to wobbling and deterioration 1. Replace the burner 2. Follow the instructions on page 12 & 13 1. Ignition not getting activated 2. Gas not flowing 3. Battery need replacement 1. Users must press the knob (>5 seconds) down enough to activate the micro switch which would ignite the igniter 2. Turning the knob would allow the gas to flow and combustion to take place 3.
Electrical connection 19 20
Electrical connection models TH 721 D22 E/LPG TH 721 D22 E/NG TH 721 D22 E/TG TH 931 D2/A E/LPG TH 931 D2/A E/NG TH 931 D2/A E/TG TH 731 D2/A E/LPG TH 731 D2/A E/NG TH 731 D2/A E/TG 21
