Kensington - 3 Drawer 3 Door Robe Assembly Instructions - Please keep for future reference 424/7429 402/7216 Dimensions Width - 127.4cm Depth - 49.5cm Height - 198.8cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 85kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below 1 Drawer Front (DF2414) (79.1 x 19.2cm) x 3 2 Left Drawer Side (W370-124LH) (37 x 12.4cm) x 3 4 Drawer Back (W765-124) (76.5 x 12.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below 19 Small Left Door (DF3874) 20 Small Right Door (DF3780) 22 Small Back (X1892-419) 23 Large Back (X1914-816) (120.6 x 39.4cm) (189.2 x 41.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 A Prepare the 3 drawer fronts A A Screw 2 metal dowels A into each of the 3 drawer fronts 1 . 1 x3 Note: Tighten the metal dowels up fully against the panels. Step 2 Prepare the drawer sides C Insert a small locking nut C into the hole shown on the left drawer side 2 and the right drawer side 3 . C C 3 2 x3 Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Assembly Instructions Step 4 Fit the drawer base 5 Slide the drawer base 5 down the grooves in the drawer sides 2 and 3 and down into the groove in the drawer front 1 . 2 3 x3 1 Step 5 Fit the drawer back Fit the drawer back 4 between the drawer sides 2 and 3 . Make sure that the drawer base 5 fits into the groove in the drawer back 4 . F F 3 4 5 F F Hold the drawer back 4 in position and tap the knock-in pegs F through the holes in the drawer sides 2 and 3 .
Assembly Instructions Step 8 J Prepare the divider P M P a: Place 3 runners M on the divider 9 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . P a: 9 J P J J M Finished front edge M Fit 3 hinge plates P onto the divider 9 , making sure that the slot is facing towards the finished front edge. M B B B b: Slide the runners M back the other way and fit the 2nd screw J into the corresponding holes in the divider 9 .
Assembly Instructions Step 9 K Turn the divider over and prepare its other surface K O A Screw 5 metal dowels A into the divider 9 . To fit the rail holder O screw through the top hole with screw K and into the mark hole drilled in the divider 9 . Make sure that it is fitted straight, in line with the panel edges and then fit another screw K using the lower hole. A Finished front edge A A Step 10 Prepare the large shelf 9 A B D D B Insert 4 large locking nuts B into the large shelf 6 .
Assembly Instructions Step 12 Prepare the narrow base 11 Narrow Base (DF3779) B Insert 4 large locking nuts B into the narrow base 11 . D D (40 x 47.4cm) B B B Tap 4 wooden dowels D into the narrow base 11 . 10 Narrow Shelf (DF3778) (40 x 45cm) 11 Finished front edge D D Step 13 Fit the narrow base to the divider Push the narrow base 11 onto the divider 9 . 9 Use a screwdriver to tighten the 2 large locking nuts B fitted to the narrow base 11 .
Assembly Instructions Step 15 Fit the narrow rail a: a: Position the narrow rail 15 .15 up against the 2 holes in the divider 9 . c: b: Tap a double metal 15 dowel V through the divider 9 and into the narrow rail 15 until it ‘’bottoms out’’. b: U 9 V Tap a large wooden dowel U through the divider 9 and into the narrow rail 15 until it ‘’bottoms out’’. U V c: Use a screwdriver to tighten the large locking nut B fitted to the narrow rail 15 .
Assembly Instructions Step 17 Fit the narrow rail to the divider 9 Push the narrow rail 15 onto the divider 9 . Use a screwdriver to tighten the large locking nut B fitted to the narrow rail 15 . 15 Step 18 B Prepare the narrow shelf Insert 4 large locking nuts B into the narrow shelf 10 . Tap 4 wooden dowels D into the narrow shelf 10 . D D B B B 10 Finished front edge D D Step 19 Fit the narrow shelf to the divider 10 Push the narrow shelf 10 onto the divider 9 .
Assembly Instructions Step 20 Prepare the right side a: Screw 6 metal dowels A into the right side 8 . D A A B D a: A Insert 2 large locking nuts B into the right side 8 . A 8 A Finished front edge Tap 2 wooden dowels D into the right side 8 . b: K Fit 4 hinge plates P onto the right side 8 , making sure that the slot is facing towards the finished front edge. To fit the rail holder O screw through the top hole with screw K and into the mark hole drilled in the right side 8 .
Assembly Instructions Step 22 P J Prepare the left side M P a: Place 3 runners M on the left side 7 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . Fit 3 hinge plates P onto the left side 7 , making sure that the slot is facing towards the finished front edge. Finished front edge P P J J a: 7 J M M M b: Slide the runners M back the other way and fit the 2nd screw J into the corresponding holes in the left side 7 .
Assembly Instructions Step 23 Prepare 4 rails B D x4 Insert 2 large locking nuts B into 4 of the rails .17 . B 17 Tap 2 wooden dowels D into 4 of the rails 17 . D Step 24 Prepare the other rail Insert 2 large locking nuts B into the rail 17 . B x1 Tap 1 wooden dowel D into the rail 17 . B 17 D Step 25 Fit the 5 rails Push the 5 rails 17 onto the divider 9 . Use a screwdriver to tighten the large locking nut B fitted to each of the 5 rails 17 .
Assembly Instructions Step 26 Fit the left side Push the left side 7 onto the assembly. Use a screwdriver to tighten the 7 large locking nuts B fitted to the large shelf 6 and the 5 rails 17 . 17 6 17 7 17 17 17 Step 27 Prepare the top A A A A Screw 6 metal dowels A into the top 14 .
Assembly Instructions Polystyrene block Step 28 Fit the top Note: To make it easier to fit the top and plinths, place polystyrene blocks from the packaging underneath the side and divider panels to raise the assembly. Polystyrene block 14 8 9 Polystyrene block 7 Push the top 14 onto the assembly. Use a screwdriver to tighten the 6 large locking nuts B fitted to the sides 7 and 8 and the divider 9 . Polystyrene block Polystyrene block Warning: The unit is heavy. Lift with care.
Assembly Instructions Step 30 Fit the 2 back panels a: The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: Square up the unit by making sure that measurement x:x equals y:y. W c: Place the small back 22 and large back 23 , coloured surface facing down, onto the unit as shown.
Assembly Instructions Step 31 Fit the 4 plastic nails Tap 2 plastic nails L into the bottom edge of each of the sides 7 and . 8 and the divider 9 . L 8 L 9 L L L 7 L Step 32 Finished top edge B Prepare a side plinth Insert a large locking nut B into 1 of the side plinths 16 . 16 D Tap a wooden dowel D into the side plinth 16 . Step 33 Prepare the other side plinth Insert a large locking nut B into the side plinth .16 . B D Finished top edge 16 Tap a wooden dowel D into the side plinth 16 .
Assembly Instructions A Step 34 Prepare the front plinth Screw 2 metal dowels A into the front plinth 18 . Profiled top edge A 18 Step 35 Finished top edge Fit the plinths together 16 Push the 2 side plinths 16 onto the front plinth 18 . Profiled top edge Use a screwdriver to tighten the large locking nuts B fitted to the side plinths 16 .
Assembly Instructions Step 37 Fit the drawers Starting with the bottom drawer, slide both the runners M forward and locate the drawer sides . 2 and 3 between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners M . Working from the inside of the drawer, insert 2 screws I through the drawer sides and out into the 2nd threaded hole in the runner. I M 3 I 2nd threaded hole I 2 Note: Do not overtighten the screws I .
Assembly Instructions Step 39 K K Prepare the 2 small doors K Q Push fit 3 hinges Q into each of the 2 small doors .19 and 20 . Secure each hinge with 2 screws K . K K 19 K Q 90 Q Q Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door. K K K K Q K 20 K Q Q Step 40 K K Prepare the large door Push fit 4 hinges Q into the large door 21 . Secure each hinge with 2 screws K .
Assembly Instructions Step 41 a: P Fit doors and handles Q A onto the front part of the hinge plate P . The recess at the bottom of screw B goes into the slot in the hinge plate. b: Keep the hinge B c: P Q Q Note: The easiest way to attach each door 19 , 20 and 21 is to fit the top hinge first, then align and fit the other hinges. a: Push the hinge b: P Q d: P P Q Q B Q FLAT against the hinge plate P as you slide it across as far as it will go. Tighten screw A.
Assembly Instructions Step 42 Adjust the doors if needed a: a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown. b: A A b: Height adjustment. Loosen screws A on hinge plates and move door up or down as required. Retighten screw A. c: B c: Forward and Back adjustment.
Assembly Instructions Step 43 Strap T Washer Strap F Screw (not supplied) U N IT Washer O Wall fixing (not supplied) Screw T P To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit .T to the unit, or an alternative fixing method of your choice. L L WA TO Fit the overbalance protector T Wall fixings are not supplied as they will need to suit the wall type.
Assembly Instructions Step 44 Assembly is complete If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
ALR3178