DR899244 New Hallingford 4 Door 3 Drawer Wardrobe Assembly Instructions - Please keep for future reference 2478441 2497714 2574242 2377700 2588771 Dimensions Width - 197,9cm Depth - 60,3cm Height -205,7cm Tip : To prevent damage, we recommend that you build your unit on the carton(s) it was packed in. Important – Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible. • Keep children and animals away from the work area, small parts could choke if swallowed.
Components - Panels For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the panels listed below 1 Left side (205.6 x 58cm) P2349b 2 Right side (205.6 x 58cm) P2349b 3 Upright x2 (196.9 x 57.7cm) P2354b 4 Left mirror door (151.2 x 48.8cm) PS3725 5 Right mirror door (151.2 x 48.8cm) PS3719 6 Top/Bottom x 2 7 Large horizontal 8 Small horizontal x2 9 Drawer base x 3 10 Drawer wrap x 3 11 Drawer front x 3 (96.7 x 57.
Components - Fittings For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 J Drawer assembly x 3 a: Insert two small locking nuts J into drawer wrap 0. a: Make sure the ‘arrow’ on J is pointing towards the hole in the edge of 0. 10 J H H b: Screw 24mm locking b screws H into holes shown on back of drawer front !. Make sure 24mm locking screws H are tightened right up against drawer front !. 11 H 11 c: Slide drawer base 0 into grooves shown on drawer wrap 0.
Assembly Instructions Step 1 - continued d: Insert glue in drawer front ! groove. Turn the drawer wrap assembly over and push onto drawer front !. Use a philips or flatblade screwdriver, that is a good fit, to turn small locking nut J as far as it will go - more than 1/2 turn. d J J 11 J X H N N N N e: Fix drawer handle T onto drawer front ! using 30mm screw B Turn over drawer and slide Drawerbase supports N in corner as shown and fix them, using the attached screws .
Assembly Instructions Step 2 - continued b b: Slide top of runners R E O 3R O R back. O 3L R 3R R Fix through 1st and 9th hole of runners R using 15mm screw O. R R O 3L O O E E E O O O Finished front edge R Note: there are no predrilled holes for 15mm screw O. Step 3 E O Fix through 3rd hole of runner R and pre-drilled holes of upright 3 using 10mm fixing screw drawer E.
Assembly Instructions Step 4 Attaching panels Unfinished back edge Position large horizontal 7 onto upright 3R . Insert two large locking nuts I into large horizontal 7 as shown. 3R I I Use a screwdriver to turn locking nuts I clockwise to lock. 7 I Step 5 Attaching panels Position large horizontal 7 onto upright 3L . Insert two large locking nuts I into large horizontal 7�as shown. Use a screwdriver to turn locking nuts I clockwise to lock. 7 I 3L I Note: Internal Uprights are identical.
Assembly Instructions Step 7 Attaching plinths Align the sides of plinth front ^ with bottom 6 as shown and attach using 40mm screw A. Note: there are no predrilled holes for 40mm screw A. Note: top and bottom panels 6 are identical. Only prepare one of the panels at this stage. This will be the bottom panel A A A 17 6 A A Finished front edge A A 16 Repeat with plinth back &. A H Step 8 H Insert locking screws H 6 Screw 24mm locking screw H into bottom 6.
Assembly Instructions Step 10 8 Attaching panels Position small horizontals 8 onto uprights 3. I I 3 I I Insert three large locking nuts I into small horizontals 8 as shown. 3 I Use a screwdriver to turn locking nuts I clockwise to lock. Warning: Do not use an electric screwdriver to attach the hinges as this can weaken the fixing. H Step 11 1 Insert fittings Note: Insert 24mm locking screw H as far as shown. Do not over tighten.
Assembly Instructions Step 13 K Fitting back panels A Attach back # and foldy back $ to back of wardrobe with the coloured surface facing the inside of the unit using nails K and 15mm screws D. Use nail holder L to hold the nails K vertical and at correct distance as you secure the back # and foldy back $. Nails K should be spaced about 150mm apart. B 14 13 A A A:A = B:B A 18 6 A U Position pelent * onto top 6 as shown, fix by using three 40mm screws A.
Assembly Instructions Step 15 Inserting drawers See page 1 for link to instruction video! a: a: Pull runners out. Slide drawers onto runners so they butt up against back of drawer front. C C b: Fix through drawer sides into runners using 9mm screws C. b: C 1st small threaded hole Step 16 Fitting hinges & door handles to doors Warning: Do not use an electric screwdriver to attach the hinges as this can weaken the fixing. D Fix three hinge doors Q to each door 35% using 15mm screws D.
Assembly Instructions Step 17 Hanging doors & attaching L-bracket a: b: Q P Q Q a: With help, slot hinge P door Q onto hinge back P. b: Tighten screw shown c: W D to lock hinges in position. G Repeat a and b for other doors. W P Q See ‘Hinge adjustment’in step 18 if the doors need adjusting. P Q c: Position L-Bracket G onto top 6 as shown, fix by using 15mm screw D. P Note: there are no pre-drilled holes for 15mm screw D.
Assembly Instructions Step 18 Warning: Do not use an electric screwdriver to adjust the hinges as this can weaken the fixing. Hinge adjustment a: To move doors up or down: loosen screws shown and move doors to suit. a: Once doors are aligned, re-tighten. See page 1 for link to instruction video! b: To move doors in or out: loosen screw shown and move doors to suit. Re-tighten screws. c: To move doors left or right: loosen screw shown and move doors to suit. Re-tighten screws.
A Guide to - Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.