Owner's Manual
Table Of Contents
- Handbook
- Safety Guidelines
- Welcome
- Contents
- Overview
- Rear Panel Connections and Controls PA720
- Rear Panel Connections and Controls PA240
- Rear Panel Connections and Controls PA410
- Control System Connections
- Front Panel Connections and Controls
- Operation
- Connecting Sources and Loudspeakers
- Bridged Mono Mode - PA240 only
- Dual Mono / Bi Amp Mode - PA240 only
- Troubleshooting
- Specifications
- Warranty
EN-16
Bridged Mono Mode - PA240
only
Bridged mono mode requires the use of a PA240 for
each channel.
Note: In bridged mode only the L+ and R+ speaker
outputs are required.
WARNING: Do not make any connections to the L- or
R- speaker terminals, doing so will severely damage
your amplier.
On one of the PA240’s, connect the RED positive
speaker terminal labelled L+ to the positive terminal of
your left speaker.
Connect the RED positive speaker terminal labelled R+
to the negative terminal of your left speaker.
Repeat this process for the right speaker, using the
SAME terminals on the other PA240.
In this setup only one interconnect is required to
each power amplier and it should be connected to
the IN L input. The interconnects can be either XLR
(recommended for longer cable runs) or phono (RCA).
Set the INPUT switch on both of the PA240’s to the
appropriate setting for the cables used.
Note: The IN R input has no function in this
arrangement.
Note: L+ must be connected to the positive speaker
terminal and R+ to the negative speaker terminal on
BOTH speakers otherwise the speakers will be out of
phase.
WARNING: Make ABSOLUTELY sure you have used the
L+ and R+ terminals of the PA240. L- and R- terminals
are NOT required in this arrangement.
RCA
XLR
INPUT
+
4-16 OHMS. CLASS 2 WIRING
+
- -
R
ST BRIDGE DM
GAIN
25dB 31dB
MODE
L
INR INL
INR
OUTR
INL
OUTL
HF
LF
HF
LF
Right
Left
RCA
XLR
INPUT
+
4-16 OHMS. CLASS 2 WIRING
+
- -
R
ST BRIDGE DM
GAIN
25dB 31dB
MODE
L
INR INL
INR
OUTR
INL
OUTL
MODE
ST BRIDGE DM
GAIN
25dB 31dB
RCA
XLR
INPUT
Note:
Make sure INPUT switch
is set to input type RCA
or XLR
It is recommended that the
GAIN switch is set to 25dB
Make sure MODE switch
is set to bridged mode,
BRIDGE
115 230
SWITCH POSITIONS
115 = 110 - 115V~
230 = 220 - 240V~
HEIGHT1 HEIGHT2
SUB 2
L
R
PREAMP OUT
FL C SL SBL
FR SUB 1 SR SBR
BD CD
PVRSAT
DIGITAL AUDIO
STB AV
OUTPUT 2
OUTPUT 1
ARC
ZONE 2
OUT
PVR
VCR
BD
SAT
AV
GAME
STB/MHL
HDMI
L
R
Z2 OUT
STB
GAME
AV
BD
PVR
CD
ANALOGUE AUDIO
ETHERNET
USB 5V
1A
FM/DAB
DC 6V
1.2A MAX
RS232
TRIG Z1 Z1 IR
TRIG Z2 Z2 IR
23425
POWER INLET
~50/60Hz 50W MAX
BALANCED OUTPUTS
FL C SL SBL HEIGHT 1 L HEIGHT 2 L
FR SUB 1 SR SBR HEIGHT 1 R HEIGHT 2 R
AV860
PREAMP OUT
FL
C
SL
SBL
FR
SUB 1
SR
SBR
FL
FR
Note: Unit should be connected via RCA or XLR.
Both versions shown for illustrative purposes
only.
PA240
PA240