600mm INDUCTION Cooktop MODEL: CI6SE1-4 Zone CI6SE2-3 Zone Ins ta l l at Io n a nd o p Er at Io n Manual
Congratulations on the purchase of your new Induction Hob. We recommend that you spend some time to read this Instruction / Installation Manual in order to fully understand how to install correctly and operate it. For installation, please read the installation section. Read all the safety instructions carefully before use and keep this Instruction / Installation Manual for future reference. Product Overview Top View MODEL: CI6SE1 1. max. 1200/1500 W zone 2. max. 2300/2600 W zone 3. max.
Control Panel 1. Power regulating key 2. Timer regulating key 3. keylock control 4. BOOST control 5. ON/OFF control Induction Cooking How It Works Induction cooking is a safe, advanced, efficient, and economical cooking technology. It works by electromagnetic vibrations generating heat directly in the pan, rather than indirectly through heating the glass surface. The glass becomes hot only because the pan eventually warms it up.
Before using your New Induction Hob • Read this guide, taking special note of the ‘Safety Warnings’ section. • Remove any protective film that may still be on your Induction hob. Using the Touch Controls • • • • The controls respond to touch, so you don’t need to apply any pressure. Use the ball of your finger, not its tip. You will hear a beep each time a touch is registered. Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. Use pans whose diameter is as large as the graphic of the zone selected.Using a pot a slightly wider energy will be used at its maximum efficiency.If you use smaller pot efficiency could be less than expected.Pot less than 140 mm could be undetected by the hob. Always centre your pan on the cooking zone. Always lift pans off the Induction hob – do not slide, or they may scratch the glass.
3. Select a heat setting by touching the “-“ or “+” control. • If you don’t choose a heat setting within 1 minute, the Induction hob will automatically switch off. You will need to start again at step 1. • You can modify the heat setting at any time during cooking.
2. Beware of hot surfaces H will show which cooking zone is hot to touch. It will disappear when the surface has cooled down to a safe temperature. It can also be used as an energy saving function if you want to heat further pans, use the hotplate that is still hot. Using the Boost function Actived the boost function 1. Select the heating zone by touching the”-“ or”+” control. 2. Touching the boost control ,the zone indicator show “P.” and the power reach Max. Cancel the Boost function 1a.
• The function can work in any cooking zone. • The cooking zone returns to its original setting after 5 minutes. • If the original heat setting equals 0, it will return to 9 after 5 minutes. Locking the Controls • You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on). • When the controls are locked, all the controls except the ON/OFF control are disabled. To lock the controls Touch the keylock control.
go on to standby in 1 minute. The fan will keep cooking down the induction hob for a further 1 minute. Auto Shutdown Protection Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you forget to turn off your cooking.
3. Set the time by touching the “-“ or ”+” control of the timer Hint: Touch the “-“ or ”+” control of the timer once to decrease or increase by 1 minute. Touch and hold the“ -“ or “+” control of the timer to decrease or increase by 10 minutes. 4. Touching the “-“ and ”+” together, the timer is cancelled, and the”00” will show in the minute display. 5. When the time is set, it will begin to count down immediately. The display will show the remaining time and the timer indicator will flash for 5 seconds.
2. Set the time by touching the or control of the timer Hint: Touch the “-“ or “+” control of the timer once will decrease or increase by 1 minute. Touch and hold the ”-“ or “+”control of the timer will decrease or increase by 10 minutes. 3.Touching the ”-“ and “+” together, the timer is cancelled, and the ”00” will show in the minute display. 4. When the time is set, it will begin to count down immediately. The display will show the remaining time and the timer indicator flash for 5 seconds.
(set to 15 minutes) 2. (set to 45 minutes) Once the countdown timer expires, the corresponding zone will switch off. Then it will show the new min. timer and the dot of corresponding zone will flash. (set to 30 minutes) Cooking Guidelines Take care when frying as the oil and fat heat up very quickly, particularly if you’re using PowerBoost. At extremely high temperatures oil and fat will ignite spontaneously and this presents a serious fire risk.
point. • Some tasks, including cooking rice by the absorption method, may require a setting higher than the lowest setting to ensure the food is cooked properly in the time recommended. Searing steak To 1. 2. 3. cook juicy flavorsome steaks: Stand the meat at room temperature for about 20 minutes before cooking. Heat up a heavy-based frying pan. Brush both sides of the steak with oil. Drizzle a small amount of oil into the hot pan and then lower the meat onto the hot pan. 4.
7-8 9 • • • • • • sautéing cooking pasta stir-frying searing bringing soup to the boil boiling water Care and Cleaning What? How? Important! Spillovers on the 1. Switch the power to the cooktop off. 2. Soak up the spill 3. Wipe the touch control area with a clean damp sponge or cloth. 4. Wipe the area completely dry with a paper towel. 5. Switch the power to the cooktop back on. 1. Switch the power to the cooktop off. 2. Apply a cooktop cleaner while the glass is still warm (but not hot!) 3.
Hints and Tips Problem Possible causes What to do The induction hob cannot be turned on. No power. The touch controls are unresponsive. The controls are locked. The touch controls are difficult to operate. There may be a slight film of water over the controls or you may be using the tip of your finger when touching the controls. Rough-edged cookware. Make sure the induction hob is connected to the power supply and that it is switched on. Check whether there is a power outage in your home or area.
The induction hob or a cooking zone has turned itself off unexpectedly, a tone sounds and an error code is displayed (typically alternating with one or two digits in the cooking timer display). Please note down the error letters and numbers, switch the power to the induction hob off at the wall, and contact a qualified technician. Technical fault.
Cooking Hob CI6SE2 Cooking Zones 3 Zones Supply Voltage 220-240V~ Installed Electric Power 7200W Product Size 590X520X56.5 L×W×H(mm) Building-in Dimensions A×B (mm) 560X490 Dimensions are approximate. Because we continually strive to improve our products we may change specifications and designs without prior notice. Installation Selection of installation equipment Cut out the work surface according to the sizes shown in the drawing.
A(mm) B(mm) C(mm) D E 760 50 mini 20 mini Air intake Air exit 5mm Induction cooktops heat rapidly and unlike other cooktops require air intake and air exhaust outlets. HEAT BARRIER Heat barrier should be the width of the internal cabinet. The barrier is fitted about midway (front to back)of the cooktop to separate the rear inlet and front outlet.It is affixed between cooktop base and the heat shield or oven.
Before you install the hob, make sure that • the work surface is square and level, and no structural members interfere with space requirements • the work surface is made of a heat-resistant material • if the hob is installed above an oven, the oven has a built-in cooling fan • the installation will comply with all clearance requirements and applicable standards and regulations • a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, moun
Cautions 1. The induction hotplate must be installed by qualified personnel or technicians. We have professionals at your service. Please never conduct the operation by yourself. 2. The hob will not be installed directly above a dishwasher, fridge, freezer, washing machine or clothes dryer, as the humidity may damage the hob electronics 3. The induction hotplate shall be installed such that better heat radiation can be ensured to enhance its reliability. 4.
• If the cable is damaged or to be replaced, the operation must be carried out the by after-sale agent with dedicated tools to avoid any accidents. • If the appliance is being connected directly to the mains an omnipolar circuit-breaker must be installed with a minimum opening of 3mm between contacts. • The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. • The cable must not be bent or compressed.
• could reduce your installation costs. • In order to avoid a hazard, this appliance must be installed according to these instructions for installation. • This appliance is to be properly installed and earthed only by a suitably qualified person. • This appliance should be connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply. • Failure to install the appliance correctly could invalidate any warranty or liability claims.
• Do not allow children to play with the appliance or sit, stand, or climb on it. • Do not store items of interest to children in cabinets above the appliance. Children climbing on the cooktop could be seriously injured. • Do not leave children alone or unattended in the area where the appliance is in use. • Children or persons with a disability which limits their ability to use the appliance should have a responsible and competent person to instruct them in its use.
PRODUCT SERVICE NUMBER 1800 805 300 RSDMC1208
