Instructions / Assembly

ManualsBrandsArboria ManualsGarden Center44.75 in. x 59.5 in. Natural Cedar Potting Bench with Classic Shelf

Product ID 820.1492 / Instruction ID 445.35.65 Updated 12/4/15

LWO Corp. / PO Box 17125 / Portland, OR / Cust. Serv. 800-459-8718

POTTING BENCH

REVIEW ALL STEPS BEFORE STARTING ASSEMBLY

GARDEN STRUCTURES

HARDWARE LIST PRELIMINARIES

TOOLS REQUIRED

ASSEMBLED PRODUCT

PARTS LIST

Quantity

4” Screw (8)

2” Screw (4)

Allen wrench (for 4” screw)

 Power screwdriver or drill

Handy to have:

 Tape measure

 Bit holder may be needed if using a drill with a

quick-change chuck

Selecting a Work Area

Select an area close to where the Potting Bench

will be installed. The assembly area should be

relatively flat and open. A lawn, driveway or

wide path will be satisfactory. It is a good idea to

lay out the box on your work surface to protect

the bench from nicks and scratches. Always use

caution when assembling or moving the bench.

Tub

Sliding Tops

Legs

Bottom Shelf

ASSEMBLY INSTRUCTIONS

Rails

Summary of content (6 pages)

PAGE 1
GARDEN STRUCTURES ASSEMBLY INSTRUCTIONS POTTING BENCH REVIEW ALL STEPS BEFORE STARTING ASSEMBLY HARDWARE LIST PB PRELIMINARIES Quantity A 4” Screw (8) B 2” Screw (4) C Allen wrench (for 4” screw) Selecting a Work Area Select an area close to where the Potting Bench will be installed. The assembly area should be relatively flat and open. A lawn, driveway or wide path will be satisfactory. It is a good idea to lay out the box on your work surface to protect the bench from nicks and scratches.
PAGE 2
GARDEN STRUCTURES ASSEMBLY INSTRUCTIONS POTTING BENCH STEP 1  Insert one rail piece into one of the leg mortises (grooves). Set the rail into the bottom of the groove. Attach two 4” screws into each leg.  Repeat that process on each leg. STEP 2  Attach the shelf to the legs at your height preference with 2” screws through the pre-drilled holes in the shelf supports (recommended 8” above ground). Product ID 820.1492 / Instruction ID 445.35.65 LWO Corp. / PO Box 17125 / Portland, OR / Cust. Serv.
PAGE 3
GARDEN STRUCTURES ASSEMBLY INSTRUCTIONS POTTING BENCH STEP 3  Set the plastic tub on the supports of the rail pieces. STEP 4  Place the sliding tops on the bench by aligning the plastic bushings into the grooved slots on the rail pieces. NOTE: If you plan on leaving your bench exposed to the weather, tub drainage may be accomplished by drilling holes in the bottom of the tub. Product ID 820.1492 / Instruction ID 445.35.65 LWO Corp. / PO Box 17125 / Portland, OR / Cust. Serv.
PAGE 4
GARDEN STRUCTURES ASSEMBLY INSTRUCTIONS POTTING BENCH ENVIRONMENT Congratulations, this garden structure is crafted from natural and chemical-free Western Cedar. Wood, as a building component, is recognized by the USDA1 as yielding fewer greenhouse gases than other common materials. The use of wood provides substantial environmental benefits when compared to oil-based plastics.
PAGE 5
GARDEN STRUCTURES ASSEMBLY INSTRUCTIONS POTTING SHELVES REVIEW ALL STEPS BEFORE STARTING ASSEMBLY PS ASSEMBLED PRODUCT HARDWARE LIST Quantity A 1¼” Screw (4) B 2½” Screw (4) PARTS LIST 1 Support posts Shelf unit 2 2 1 TOOLS REQUIRED  Power screwdriver or drill Handy to have:  Tape measure  Bit holder may be needed if using a drill with a quick-change chuck Instruction ID 445.35.66 Updated 12/4/15 LWO Corp. / PO Box 17125 / Portland, OR / Cust. Serv.
PAGE 6
GARDEN STRUCTURES ASSEMBLY INSTRUCTIONS POTTING SHELVES STEP 1  Attach shelf unit to support posts with 1¼” screws through the predrilled holes. Align the vertical ends of the shelf flush to the edge of the support. STEP 2 NOTE: Assemble the shelf to post supports with the spacing blocks on the same side as the shelf. ENVIRONMENT  Align the top of the spacing block (on the support post) to the top of the leg, centering the shelf assembly to the back of the bench.