ITEM #0065835 0065487 BATHROOM FAUCET ® AquaSource is a registered trademark of LF, LLC. All Rights Reserved. MODEL #67509-6001 67509-6027H2 Francias / Español p. 10 ATTACH YOUR RECEIPT HERE Serial Number ____________ Purchase Date ____________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday. Lowes.
PACKAGE CONTENTS A B C M I N G O S U W P H J V R D E T Q F K L PART A B C D E F G H I DESCRIPTION J Spout Hot End Valve Cold End Valve Washer (Preassembled to Hot End Valve (B) and Cold End Valve (C)) Bracket (Preassembled to Hot End Valve (B) and Cold End Valve (C)) Locking Screw (Preassembled to Bracket (E)) Metal Washer (Preassembled to Spout (A)) Nut (Preassembled to Spout (A)) Block (Preassembled to Spout (A)ǃHot End Valve (B) and Cold End Valve (C)) Hose K L M N O P Q R S T U V W Q
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. WARNING: Follow the installation instructions carefully. Proper installation is the installer’s responsibility. Failure to follow correct installation procedures can result in the faucet being loose, which can result in serious injury. CAUTION: Check local building codes before beginning installation to ensure compliance.
ASSEMBLY INSTRUCTIONS 2. Install the spout (A): 2 a. Remove the preassembled metal washer (G) and nut (H) from the spout (A) and place the spout (A) through the center hole of the sink. A b. From underneath the sink, thread the metal washer (G) and nut (H) onto the spout (A). c. Turn the nut (H) clockwise to secure the spout (A) to the sink. G H 3. Install the hot and cold end valves (B and C). 3 a. Position the hot and cold end valves (B and C) on the sink.
ASSEMBLY INSTRUCTIONS 5. Connect a 1/2 in. IPS faucet connector or coupling nuts (not included) with 3/8 in. O.D. ball-nose risers (not included) to the water supplies underneath the sink using wrenches (not included). 5 Note: Refer to the local plumbing codes for permissible types of water supply connectors. 6.
ASSEMBLY INSTRUCTIONS 8. Apply silicone sealant (not included) to the underside of the (N). 8 N 9. Insert the pop-up body (Q) into the sink and screw the (N) onto the pop-up body (Q). Ensure the pivot hole is facing the back of the sink. Tighten the nut (P) and remove the pivot nut (R). 9 N P R Q 10. Insert the stopper (M) onto the sink. Remove the preassembled horizontal rod (S) and clip (T) from the lift rod strap (V).
ASSEMBLY INSTRUCTIONS 11. Re-attach the lift rod strap (V) to the horizontal rod (S) using the clip (T). 11 V T S 12. Insert the lift rod (W) through the spout (A) and into the lift rod strap (V). Tighten the screw (U) on the lift rod strap (V). 12 W A U V OPERATING INSTRUCTIONS 1. After the installation is complete: 1 a. Turn on the water supply and allow both hot and cold water to run for at least one minute each. b. While the water is running, check for leaks. 7 Lowes.
CARE AND MAINTENANCE Clean carefully by gently wiping with a grit-free damp cloth. Use only mild soap with water. Never use acids, harsh chemicals, or abrasive detergents to clean the surface. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION There is a leak from under the handle. The cartridge is damaged. Remove the handle and replace the cartridge. The spout has a leak. The cartridge is damaged. Remove the handle and replace the cartridge.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.
