LS 1 Product Manual English
Foreword Thank you for purchasing the Light Storm LS 1 The Light Storm LS 1 includes LS 1s and LS 1c. It is made of 1536 lamp beads which are designed and manufactured carefully to have over 95 CRI value. Delicate design and elaborating production make a robust but exquisite housing, which can fulfill low forward heat of the fixture. LS 1 offers dual power solutions. You can use V-Mount or Anton Bauer battery in a location shooting. Besides, adapter attached is for your indoor shooting.
Item check list Before starting, please check that all the following items have been included with the Light Storm LS 1. If anything is missing, contact your dealer immediately.
Nomenclature 1. Light Cable box Tilt knob Cooling fins NO.:6T001000 UID Barn door frame LED beads Barn door Hook U-frame Supporting Clamp tube handle Light label 2. Controller box Antennas (*The signal strength is the best Eyelet bar Socket when pulling the antennas as the picture's show.) Power switch Display window Battery mount Brightness wheel (*Anton Bauer or V-mount) Color temperature wheel (*only for LS 1c) Controller box label UID DMX input/output NO.
4. Display window Groups indicator Channels indicator DMX indicator Brightness percent indicator Color temperature indicator (*only for LS 1c) Channel setting button DMX model setting button DMX channel setting button(+) Group setting button DMX channel setting button(-) Installations 1. Install the hook 2. Install the light 1) Turn around the clamp handle to install the light on the tripod. 2) Set the light at a specific angle, and pull or turn around the tilt knob to fasten the light.
3. Insert the connect cable dot to dot to power the light . *Tie the connect cable around the hook 4. Power the controller box 1) Powered by the adapter Locking spring AC 100V-240V Locking slot * Please pull the power adapter out by pushing the locking spring down on the controller box.
2) Powered by the battery V-Mount Battery Anton Bauer Battery * Battery output current ≥ 8A; * Please choose the model of the Light Storm by your battery need. 5. Clip the tracing paper by the clamps 6. Insert the button battery to power the controller.
Operations 1. Press power switch to turn on the Light Storm LS 1. *“Channel 1 ,Group A” is by default. *The brightness is 10% and the color temperature is 3200K(LS 1c) by default. 2. Manual controlled by the controller box 1) Brightness adjustment and display 2) Color temperature adjustment and display (*only for LS 1c) 3. Remote controlled by the controller You can control the LS 1 of channel 2, group C according to the following directions.
*2) Group setting and display 2) The controller setting and display Press ( ) to set the channel 2 “ ” indicator lights The controller setting is finished. *The Light Storm has three channels (1/2/3) and four groups (A、B、C、D). 3) Brightness and color temperature adjustment Press ( or ) of group C to adjust the brightness and ( or ) of group C to adjust the color temperature. The brightness varies in 1%, and the color temperature varies in 100k at one press.
4.
2) The DMX setting *1) Press DMX model setting button on the controller box to enter into the DMX model. *2) Press the DMX channel setting button (+/-) on the controller box to your needed DMX channel. 3) The standard DMX console control Control the Light Storm by the standard console within the same DMX channel setting as above. * Channel 1 is by default when in DMX model. * DMX channel is between 1 and 512, but is between 1 and 511 for the Light Storm LS 1c.
Specifications Model LS 1c LS 1s Operation Current 8A 8A Power Supply DC 15V DC 15V Power Input 120W 120W Beam Angle 45° 25° Color Temperature 3200K-5500K 5500K Average Life Span ≥100,000 hours Cooling Mode Radio Frequency Natural convection heat transfer 2.4GHz Channels 1/2/3 Groups A/B/C/D Remote Range ≤100m Light Sizes (L*W*H) 377.8*320.7*33.2 mm Controller box 238.0*118.7*48.1 mm (*vertical antennas included) Controller box 238.0*118.7*59.
