® LR510 Self Levelling Rotary Laser Level USER GUIDE
LR510 Lufkin LR510 Horizontal self-levelling by magnetically-dampened pendulum system, vertical alignment via adjustable base. Laser 635 nm, accuracy 2 mm / 10 m, dust and splash protected to IP 54. Self-levelling range, 3.5° with tilt alarm. For all horizontal and vertical alignment work. The plumb up vertical reference beam is suitable for dropping a perpendicular line or for aligning partition walls. The wall/floor bracket can be used to level the unit vertically or fasten it to a wall.
LR510 Plumb beam aperture Rotating laser window Carry handle Bubble adjusting point Control panel Bubble for vertical operation Note: During transport and in vertical operation, make sure that the pendulum lock is set to “lock” failure to do so may result in damage to the d evice.
LR510 Battery cover Charger / power supply socket Pendulum Lock Vertical foot recepticle used in vertical operation 4
LR510 Horizontal use of LR510 • Set up the LR510 on a surface that is as level as possible or fasten it to a tripod. • Turn the pendulum lock in the arrow’s “Unlock” direction to its limit. This releases the locking mechanism that protects the pendulum during transport. • Press the On/Off button. • Within its range of +/- 3,5°, the LR510 will level itself automatically and the prism head will begin to turn. • The speed of rotation can be changed using the up & down buttons from 100 - 300 RPM.
LR510 Control Panel: Laser Speed & Scan Direction Button: In continuous rotation mode: Increase speed In scan mode: Scan range shifts clock wise Laser Speed & Scan Direction Button: In continuous rotation mode: Reduce speed In scan mode: Scan range shifts counter clock wise Scan mode button On/Off button: push the button to power the laser on or off SCAN MODE INDICATOR: CONTINUOUS GLOW indicates continuous rootation FLASHING indicates scan Power Indicator: GLOWING indicates ON NOT GLOWING indicates OFF
LR510 Laser Detector & Remote Control Unit: Horizontal vial Level reference grove LCD Detector bracket Backlight Hand receiver mode Volume On off switch Laser beam receiver Laser Detector Laser Speed & Scan Direction Button: In continuous rotation mode: Increase speed In scan mode: Scan range shifts clock wise Laser Speed & Scan Direction Button: In continuous rotation mode: Reduce speed In scan mode: Scan range shifts counter clock wise Scan mode Off switch Remote Control Unit 7
LR510 Gradient Mode: • Turn the pendulum lock in the arrow’s “Lock” direction to its limit. Now the tilt function is inactive and the unit cannot align itself automatically. • Press the On/Off button. The prism head will begin to rotate. • The speed of rotation can be changed using the up & down buttons. • Adjust the unit to the desired angle. Slope angle can be set precisely and quickly with the aid of the optional tilt plate, Part No.
LR510 Operation of the LR510 • Open the battery compartment, insert the battery pack with the exposed metal ends of the battery pack aligned with the + & - terminals (see pictures on right). Close the battery compartment. Charging the batteries • Before using the LR510, fully charge the batteries. • Connect the battery charger/mains unit to a mains source and plug into the socket. Please only use the charger/mains unit supplied with the device. If a different one is used, the warranty will become void.
LR510 Technical Specifications LR510 Specifications Self-levelling range ± 3.5° (horizontal) Accuracy ± 3mm / 10m Vertical levelling manual Perpendicular reference beam 90° to rotation plane Rotation speed 100 - 300 rpm Laser wavelength 635 nm Laser Class IIIA (EN60825-1:2007-10) Laser output rating ≤ 5 mW Rechargeable Batt. / batt. operating time approx. 20 h / 45 h, 4 x type AA Battery recharging time approx.
LR510 Calibration Check To check the calibration of the LR510 Laser, place the Laser on a surface or preferably a tripod approximately 10m from a wall or post with the control panel away from the wall or post. 1. Release the pendulum lock and switch on the Laser. 2. Mark the level point on the wall or post and label this point “A” using the detector. 3. Rotate the Laser on the surface or Tripod 180º. Be certain NOT to move or adjust the tripod.
Limited Lifetime Guarantee Apex Tool Group quality products are Guaranteed against any defect in material or workmanship. Damage caused by abuse, improper use or excessive wear is not covered by this warranty. This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
