User's Manual
Table Of Contents
- Scope of This Manual
- Conventions Used in This Manual
- Intended Audience for this Manual
- General Cautions and Warnings
- What is new?
- Overview Of Base Station
- 1.1 Conceptual Overview of the PacketMax System
- 1.1.1 Cell Size, Capacity, and Scalability
- 1.1.2 Frequency Bands
- 1.1.3 PacketMax Network Connectivity
- 1.2 Bridge Mode and VLAN Mode of Base Station
- 1.2.1 Bridge Mode
- 1.2.2 VLAN Mode
- 1.2.3 Point-to-Point Mode
- 1.3 Features of PacketMax System
- 1.3.1 The PacketMax System’s IP Network
- 1.3.2 Services
- 1.3.3 MIBs
- 1.3.4 Service Offerings and QoS
- 1.3.5 ARQ Feature
- 1.3.6 3 DES Encryption
- 1.3.7 Certificates and Management
- 1.3.8 Upgrades
- Base Station Components
- 2.1 PacketMAX Base Station
- 2.2 5-Slot ATCA Chassis
- 2.3 Wireless System Controllers
- 2.3.1 Major Differences Between WSC-S-24 and WSC-48
- 2.3.2 One Port WSC-S-24
- 2.3.3 QUAD Wireless Controller (QWC) Card - WSC-48
- 2.3.4 Compatibility matrix with radio
- 2.4 Main System Controller Card
- 2.5 MSC Redundancy
- 2.5.1 Redundancy support
- 2.6 AC Supply
- 2.7 Power LEDs and ESD connector
- 2.8 Hot Swap
- 2.8.1 WSC-48 Hot Swap
- 2.8.2 WSC-S-24 Hot Swap
- 2.8.3 MSC Hot Swap
- 2.9 Maintaining Proper Chassis Air FLow
- 2.10 Fan Unit
- 2.11 Serial Cable Pinout
- 2.11.1 Serial Connection Instructions
- 2.12 PacketMax 5000 Rear Panel
- 2.12.1 Grounding
- 2.12.2 DC Power Connection
- 2.13 AC Power Connection
- 2.13.1 Fuse
- 2.14 Base Station Radio
- Installing the Base Station IDU
- Installing the Base Station ODU Radio and Antenna
- 4.1 Radio Compatibility
- 4.2 Installing the Antenna
- 4.3 Installing the Base Station Radio ODU
- 4.3.1 3.3 and 3.5 GHz BSR Package Contents
- 4.3.2 5.8 GHz BSR Package Contents
- 4.3.3 Preparing and Mounting the 3.3 and 3.5 GHz BSR
- 4.3.4 Preparing and Mounting the 5.8 GHz BSR
- 4.3.5 Using the BSR with the Antenna and IDU
- Commissioning the Base Station
- 5.1 Summary of Configuration of Base Station
- 5.2 Establishing an Ethernet Connection with Cat-5 Cable
- 5.3 Establishing a Serial Connection to the Base Station
- 5.4 Configuring DHCP
- 5.5 Obtaining the MAC Address of the Base Station
- 5.6 Selecting Management or Data Traffic
- 5.7 Provisioning the Base Station with WaveCenter EMS
- 5.8 Rebooting the Base Station
- 5.9 Verifying Operations
- 5.10 Ensuring Encryption
- 5.11 Upgrading Base Station Manually
- 5.11.1 WSC upgrade
- 5.11.2 MSC Upgrade
- Event Reporting
- Command Line Interface (CLI)
- Cables, Spares and Accessories
- System Specifications
- D.1 Physical interfaces of PM 5000 - 12 sector
- D.2 Physical interfaces of PM 5000 - 4 sector
- D.3 QoS and Networking Parameters
- D.4 Dimensions and Weight
- D.5 Environmental
- D.6 Radio Specifications
- 4.6.1 PM-BSR-33 and PM-BSR-35 Radio Specifications
- 4.6.2 PM-BSR-58 Radio Specifications
- 4.6.3 Antenna Specifications
- D.7 Antenna Types, Maximum Gains and Maximum Output Power Point to Multipoint Operation
- D.8 Transmit Output Power Regulations
- Certifications
- Troubleshooting
A–4
PacketMax 5000 Installation and Operation Manual, 10007678 Rev J
Chapter A. Event Reporting
Cfg File Parse Error CPE Name: <name>, CPE
Mac Addr:
0xAA:0xBB:0xCC:0xDD:0x
EE:0xFF , CPE Id: <Id>:
CPE CFG File Parse Failed
CPE Name: <name>, CPE
Mac Addr:
0xAA:0xBB:0xCC:0xDD:0x
EE:0xFF , CPE Id: <Id>:
CPE CFG File successfully
Parsed
MSC Cfg File Successfully
Parsed
MSC Cfg File Parse Error
Version mismatch between
EMS & Base Station
Upgrade either the
device or EMS to
match the version.
Task Suspend Task SUSP
System RAM: LOW
All Tasks are not working
properly
Contact Aperto
MSC Mgmt Port
Mode Change
Mgmt Port Link Status is UP
Mgmt Port Link Status is
DOWN
Link Up, Mgmt Port Operat-
ing in Full Duplex Mode
Link Up, Mgmt Port Operat-
ing in Full Duplex Mode
Link Up, Mgmt Port Operat-
ing at 100 Mbps
Link Up, Mgmt Port Operat-
ing at 10Mbps
One of the following on the
management port has
changed:
- Speed
- Mode
- Duplex
If not indicated, check
network
MSC Backhaul Port
Mode Change
1G Backhaul Link Down
1G Backhaul Link Up
10/100 Backhaul Link Down
10/100 Backhaul Link Up
One of the following on the
management port has
changed:
- Speed
- Mode
- Duplex
Check network
MSC-WSC Back-
plane Port Mode
changes
WSC 1/Redundant MSC
Link Down
WSC 1/Redundant MSC
Link Up
WSC <Port No> Link Down
WSC <Port No> Link Up
One of the following
between the MSC-WSC has
changed:
- Speed
- Mode
- Duplex
Contact Aperto
Table A-2 MSC related Alarms/Events in PM 5000