Introduction 1 Copyright Copyright © 2000 by AOpen Inc. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of AOpen Inc. AOpen makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice.
Table of Contents 1. Introduction........................................................................... 1-1 1.1. 1.2. 2. Parts Description.................................................................. 2-1 2.1. 2.2. 2.3. 2.4. 2.5. 2.6. 2.7. 3. Opening Chassis ............................................................................... 3-1 Installing Motherboard into Chassis................................................... 3-2 Fastening Slide Rails to FDD and 5.25” CD-ROM...............
Introduction 1. 1-1 Introduction The H800 is a user-friendly server chassis that has been tested and found to be complied with the restrictions for a Class B device of the FCC Rules, CE, C tick and all EMC requirements. Any accessing, upgrading and maintenance operation to the system can be easily performed and done.
1-2 1.1. Introduction Configuration Dimension: Front panel, foot stand excluded: (H x W x D) 16.93 x 8.58 x 21.65 in. (430 x 218 x 550 mm), Front panel, foot stand included: 17.72 x 8.58 x 23.43 in. (450 x 218 x 595 mm) Motherboard Support to 12 x 13 in. (305 x 330 mm) Size: Baby AT, Full ATX & AT, and SSI M.B. (W x L) Drive Bays: Nine external 5.25” drive, one FDD, one HDD cage. (2*5.
Introduction 1.2.
1-4 Introduction nd Redundant power supply: 337W (with or without 2 power) Standard ATX 12V power supply: 350 / 400W ATX power supply Rack mount assembly kit (optional) Support 5U rack mount accessories Hot swap HDD cage (optional) BPL6: Support 6pcs Hot swap SCSI HDD (4 x 5.25” changeable to 6 x 3.5” HDD) Chassis key lock and Key set Support key lock solution to provide security solution Air filter Supporting air filtering HDD cage for three 3.5” HDD and one optional 8 cm fan 2 x 5.
2-1 Parts Description 2. Parts Description The H800 is designed to maximize the extension ability of the system for you to access, upgrade, and maintain it.
2-2 2.1. Parts Description Front Cover and Front Panel The H800 is designed with a key lock on the door to protect against inadvertent access to the power button, reset button, and disk drives. Behind the door are mountings for nine 5.25” and one 3.5” drive bays, one Power button, one Reset button, one Intrusion Alarm Detector, and three LED indicators. 2.1.1. Front Cover Key Lock: This is a mechanical key lock, which lock all components inside the door.
2-3 Parts Description 2.1.2 Front panel Drive Bays: The H800 is designed with nine 5.25” drive bays and one 3.5” drive bays. You can occupy the space of two 5.25” drive bays with one standard HDD cage; and the space of HDD cage can be occupied with three 3.5” IDE HDD likewise. The Drive Bays can be easily arranged based on your needs to have the best system performance. 3.5-inch Drive Bays 5.
2-4 2.2. Parts Description Back Panel There are four components available to be installed on the back panel of H800: (1) Power Supply, (2) I/O Ports, (3) Expansion Slots, and (4) Housing Fans. 2.2.1 Power Supply The H800 provides 2 solutions: 1. Standard ATX 12V 350W/400W power supply : you have to assemble this standard ATX 12V power together with the power bracket before installed to chassis. Standard ATX 12V 350/400W Power Bracket b nd 2.
2-5 Parts Description 2.2.2 I/O Ports The H800 provides standard ATX ports bracket, which meets the standard definition of PC99. For detail output, please see the following diagram: 2.2.3. Expansion Slots All of the I/O signals go through the ATX I/O ports; and there’re 7 expansion slots at the rear panel in total. 2.2.4. Housing Fans The H800 has a built-in 8cm FAN and one optional 8cm FAN on its back panel.
2-6 2.3. Parts Description Main Body The H800 provides a strong structure and impediment-free design for easy assembly. 9x5.25” drive Sliding in or screwing for components assembly Long Card Guide x2 pcs MB size: supports up to 12x13” MB with Pentium4 CPU mounting holes MB type: SSI, Full ATX, AT & Baby AT Foot for stand-alone Long Card Guide x2 pcs P/N: 42.96501.
2-7 Parts Description 2.4. Cooling System The H800 is equipped with one 8cm fan at the rear panel, and is also possible to add one more optional 8cm fan to make it a two-fan cooling system. There is one more optional way of adding another 8cm fan to the 3.5” HDD cage located at front panel. All fans are hot swappable, allowing users to replace malfunctioning fans without turning off the system. g g If you want to install one more 8cm fan, you must take out the fan cover first.
2-8 2.5. Parts Description Security Device The H800 has one mechanical key lock on the front panel cover and one electrical chassis intrusion alarm to prevent unauthorized access to components inside the chassis. The chassis intrusion alarm is an electrical detecting device that came with the motherboard. It will alarm whenever the front panel or side panels are opened. The overall security system protects this server chassis perfectly.
2-9 Parts Description 2.6. Power Supplies nd The H800 supports standard ATX 12V and redundant 337W (with or without 2 power) power supplies. 2.6.1 Standard ATX 12V power supply Before Assembly standard ATX 12V power supply, it must assemble power bracket with power than can install to chassis. Standard ATX 12V 350/400W Power Bracket b Standard ATX 2.6.1.1. 350W ATX 12V Power Supply Specification GENERAL REQUIREMENTS This specification describes a 350 watts power supply.
2-10 Parts Description INPUT REQUIREMENTS The power supply shall operate from 95 to 132 Vrms or 180 to 264 Vrms. The power supply shall operate from an AC mains frequency of 47 through 63 Hz. The Ac mains single-cycle peak inrush current shall be limited to 80 amps cold, 100 amps warm measured at 132 Vrms, 60 Hz and coinciding with the AC main voltage peak. The AC mains steady-state RMS input current shall be: 10 amps maximum / 115 Vrms, 60 Hz. 5.0 amps maximum / 230 Vrms, 50 Hz.
2-11 Parts Description -Primary to Secondary : 1800 Vac for 1 sec. INSULATION RESISTANCE -Primary to Secondary : 20 Meg. ohms Minimum. -Primary to FRAME GROUND : 20 Meg. ohms Minimum. GROUND LEAKAGE CURRENT -The power supply ground leakage current shall be less than 3.5mA. EMISSION REQUIREMENTS -When testing the power supply must operate within the listed requirements.
2-12 Parts Description OUTPUT REQUIREMENTS OUTPUT VOLTAGE AND CURRENT *+3.3V MINIMUM LOAD NORMAL LOAD MAXIMUM LOAD 0.2A 14.0A 10.6/28A LOAD REG. ±5% RIPPLE & NOISE 50mV P-P +5V 2.0A 14.0A 40/28.5A ±5% 50mV P-P +12V 0.2A 6.0A 15A ±5% 120mV P-P -12V 0.0A 0.4A 0.8A ±5% 100mV P-P -5V 0.0A 0.15A 0.3A ±5% 100mV P-P +5Vsb 0.0A 1.0A 2.0A ±5% 50mV P-P *OPTIONAL (1) +3.3V &+5V total output not exceed 235 W. When +3.3V is load to 28A,the +5V maximum load is 28.5A. When +3.
2-13 Parts Description When testing the power supply must operate within the listed requirements. OTHER REQUIREMENTS COOLING With the fan voltage set to around 12 volts, the fan will deliver greater than 38 CFM with the power supply in open air. INPUT CONNECTIONS Refer to Mechanical Specifications for placement. The AC mains input are through a three-circuit IEC type connector mounted on the rear of the power supply chassis.
2-14 Parts Description 1 x 337W Main power only Support Redundant 337W x 2 2.6.2.1. DPS-300AB-1A 337W redundant Main power module specification General description : This specification describes the performance characteristic of 337 watts Hot-swap redundant power unit with +5V, +12V,+3.3V,-5V and –12V DC outputs. Forced output current share : the SPS unit(DPS-300AB-1) is intended to work with cage unit(RPS-600A) to form a redundant power module.
2-15 Parts Description DPS-300AB-1) shall meet the IEC-1000-3-2 Standard. (7) Electrical performance should compatible with RPS-600A. Static Output Characteristics: OUTPUT VOLTAGE LOAD RANGE MIN. +3.3V 0.5A 14A +5V 0.5A +12V LOAD RANGE REGULATION MAX. RIPPLE P-P MAX. RIPPLE +NOISE +4% ~ -4% 50mV 80mV 33A +5% ~ -5% 50mV 100mV 0.2A 10A +5% ~ -5% 120mV 200mV -5V 0A 0.3A +10% ~ -10% 100mV 200mV -12V 0A 0.5A +10% ~ -9% 200mV 200mV 5V AUX 0A 0.
2-16 2.6.2.2. Parts Description RPS-600A 337W redundant power cage Specification General description : This specification describes the performance characteristic of 337 watts Hot-swap redundant power supply with +5V, +12V,+3.3V,-5V and –12V DC outputs. Forced output current share : this module (RPS-600AB A) is intended to work with two Power supplies module (DPS-300AB-1) to form a redundant power system.
2-17 Parts Description Conducted EMI : -FCC docket 20780. Part 15. Class B. -CISPR 22. Class B. -BZT vfg 243 Class B requirements -VCCI class 2 requirements. Product safety : this power supply is designed to meet the following specs. -UL 1950.3rd . edition./CUL -CSA C22.2 NO. 950-95 -IEC-60950 2nd edition. -VDE, TUV. -CCIB. -CE marking. -B.C.I.Q. Environment : -Operating temperature: 5 to 50 dec.C (dual power supply operate in system) -Operating relative humidity: 20% to 90%.
2-18 2.7. Parts Description Drive Bays The H800 is consists of nine 5.25” drive bays and one 3.5” floppy drive bay. The nine 5.25” drive bays are designed horizontally on the front panel from top to bottom, while the 3.5” floppy drive is vertically designed on the upper right side of it. These drive bays can be installed by screw or slide rails. install the rail with HDD cage then slide in to chassis. FDD If it desn’t support spare rail, the drive can assembly by screw It can use 2 X 5.
Optional Parts Lists 3. Installation 3.1. Opening Chassis 4-1 Unlock the key lock on the front panel cover. Open the front cover to about 90 degrees and take it off. Unscrew the four thumb screws on the left and right side cover Pull the left and right side covers straight off to release them.
3-2 3.2. Optional Parts Lists Installing Motherboard into Chassis This server chassis supports the motherboard form factor of SSI, Baby AT, AT, Full ATX & AT, which can be integrated into a standalone or standard 19” rack mount, and thus greatly enlarges its working field. H800 provides an Intel standard I/O port bracket, please check the motherboard I/O port to see whether it can meet the size and port output or not.
4-1 Optional Parts Lists 3.3. Fastening Slide Rails to FDD and 5.25” CD-ROM Secure each slide rails on the left and right side of FDD with four screws. Connect the FDD cable. Choose screw hole for slide rails and then secure each slide rails on the left and right side of 5.25” CD-ROM with four screws. (please screw your device to the c-hole on the rail if the device is a standard type. If not, please adjust the screw hole to meet request. ) P/N: 50.01905.001 d d d d P/N : 60.96505.
3-4 3.4. Optional Parts Lists Installing FDD and 5.25” CD-ROM into Chassis Slide the FDD with slide rails and cables into the drive bay. Slide the 5.25” CD-ROM with slide rails into the drive bay. You may fasten the 5.25” CD-ROM with four screws if the slide rails are not available. e d The 1st location don’t support screw way, it just can support rail way only.
4-1 Optional Parts Lists 3.5. Installing HDD Cage into Chassis Note: The hard disk is a sensitive mass storage device. Any accidentally impact on the hard disk might cause serious damage, so please handle it with care. Insert the 8cm fan into the HDD cage for a better heat-dissipation if necessary and fasten it with four screws. Secure each slide rails on the left and right side of HDD cage with four screws. Fix the HDD into HDD cage by screw. Slide the HDD cage into the drive bay.
3-6 3.6. Optional Parts Lists Final Assembly Install CPU and RAM module onto the motherboard, and install Add-on card if necessary. Connect cables to the correct position step by step according to the motherboard manual. Connect other devices (keyboard, mouse, monitor) and try to power on to check the system configuration. Slide the side panel and fasten it with thumbscrew before putting down the front panel and lock.
4-1 Optional Parts Lists 3.7. Rack Mount Placement Release all handle, wheels, and foot stands first. Release top cover. Screw off the top cover 6pcs screw then change the top cover to rack mount type and screw on. For another assembly please follow up rack mount kits install manual for detail. Secure each slide tracks on top and bottom of the cover with three screws. Put the chassis into the rack mount.
3-8 3.8. Optional Parts Lists Explosive View, parts and icon 3.8.1. ITEM Explosive view Q’TY ITEM 1 ASS’Y L-CASE ACER 002( C ) H800 PARTS NAME 1 15 SPRING EMI (LONG) 8 2 PANEL ASS’Y 1 16 BOX FOR H800 ACCESSORY 1 3 SIDE COVER 2 17 ASSY I/O BRACKET A3.
4-1 Optional Parts Lists 3.8.2. parts A FOOT STAND P/N : 60.96512.011 B C MAIN BOARD I/O BRACKET A3.2 P/N : 60.96533.001 D FOOT BASE P/N : 42.96504.001 FAN COVER P/N : 42.96514.001 E FDD RAIL P/N : 34.96508.001 F RAIL P/N : 60.96505.001 G EMI COVER P/N : 34.96504.001 H THUMB SCREW P/N : 86.2R526.AR5 I 2ND FAN 500mm 3PIN P/N : 60.96526.001 J ASS HDD CAGE WITH 8CM FAN P/N : 60.96504.001 ASS HDD CAGE WITHOUT FAN P/N : 60.96504.
3-10 3.8.3. accessory box 3.8.4.
4-1 Optional Parts Lists 4. Optional Parts Lists 4.1. WH (wheels and Handle) kit (Optional) The H800 is convenient in transportation with two wheels at the lower front side and one handle at the rear panel side under power supply.
4-2 Optional Parts Lists Wheels 4.2. Rack Mount Assembly kit The H800 can be easily served as a standalone or rack mount system. Detail please see the manual of Rack mount kit.
5-1 Technical Support 5. Technical Support 5.1. How to Get Technical Support Dear Customer, Thanks for choosing AOpen products. To provide the best and fastest service to our customer is our first priority. However, we receive numerous emails and phone-calls worldwide everyday, it is very hard for us to serve everyone on time. We recommend you follow the procedures below and seek help before contact us. With your help, we can then continue to provide the best quality service to more customers.
5-2 5.2. Technical Support How to contact us Please do not hesitate to contact us if you have any problem about our products. Any opinion will be appreciated. Pacific Rim Europe AOpen Inc. AOpen Computer b.v. Tel: 886-2-2696-1333 Tel: 31-73-645-9516 Fax: 886-2-8691-2233 Fax: 31-73-645-9604 China Germany 艾尔鹏国际上海(股)有限公司 Tel: 49-2102-157700 AOpen Computer GmbH. Tel: 49-2102-157700 Fax: 49-2102-157799 Fax: 49-2102-157799 America AOpen America Inc.
