LV-667 Mini-ITX Motherboard User’s Manual Edition 1.
LV-667 User’s Manual Copyright Copyright 2004 - 2005. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.
LV-667 User’s Manual Packing List Please check the package before you starting setup the system Hardware: LV-667 series motherboard x 1 Cable Kit: 40-pin ATA100 IDE flat cable x 1 26-pin slim type floppy cable x 1 Serial ATA ribbon cable x 1 I/O Shield x 1 SDTV cable (LV-667T only) DVI output cable kit (LV-667D only) Other Accessories: YPrPb component cable (LV-667T only) Divers CD (including User’s Manual) x 1 3
LV-667 User’s Manual Index Chapter 1 ..................................................................................... 7 1.1 ................................................................................. 7 1.2 ........................................................................... 8 1.3 ........................................................................... 11 1.4 .....................................
LV-667 User’s Manual 2.15 ............................................................... 32 2.15.1 .......................................................................... 32 2.15.2 ...................................................................... 32 2.16 ......................................................................... 33 Chapter 3 .............................................................
LV-667 User’s Manual (The Page is Left For Blank) 6
LV-667 User’s Manual Introduction Chapter 1 1.1 LV-667 is the Mini-ITX motherboard based on VIA chipset. It integrates the last VIA embedded chipset for CN400 with VT8237, DDR266/333/400 SDRAM, and serial ATA with RAID to provide the economical embedded platform.
LV-667 User’s Manual Introduction 1.2 General Specification Form Factor CPU Memory Chipset BIOS Green Function Watchdog Timer Real Time Clock Enhanced IDE Serial ATA Mini-ITX motherboard Embedded VIA C3/Eden processor Ratio: 1.0GHz/800MHz L1/L2 Cache: 128/64KB Front side bus: 133MHz Fanless with Eden 800MHz processor Optional up to 1.2GHz with 200MHz FSB 1 x 184-pin DDR 266/333/400 SDRAM up to 1GB Unbufferred, none-ECC memory supported only VIA CN400 and VT8237 Phoenix-Award v6.
LV-667 User’s Manual Introduction Optional SDTV/HDTV Interface Codec TV system Output Interface Output Format VIA VT1625 NTSC (M and J) or PAL (B, D, G, H, I, M, N and Nc) TV system Composite, S-Video, Component (YPbPr) and D terminal SDTV output mode for 525p or 625p HDTV support for 1080i (D3) and 720p (D4) NTSC - 525i(480i) , 525p(480p) , PAL - 625i(576i) , 625p(576p) , HDTV - 1080i , 720p Resolution Optional DVI Interface Codec Standard Input Clock Resolution Output Interface VIA VT1632 Compliant w
LV-667 User’s Manual Introduction Software support Operation System Windows 98SE/ME, Windows 2000, Windows XP Windows CE 4.0 or later, Windows XP Embedded Linux (Fedora Core 1, Mandrake 9.2 and Red Hat 9.0) Ordering Code LV-667 VIA CN400 with Embedded C3 1.0GHz, VGA, SATA, 5.1CH Audio, CF, PCI, 4 x RS232, Dual LAN, Mini-AGP LV-667D VIA CN400 with Embedded C3 1.0GHz, VGA, SATA, 5.1CH Audio, CF, PCI, 4 x RS232, Dual LAN, DVI LV-667T VIA CN400 with Embedded C3 1.0GHz, VGA, SATA, 5.
LV-667 User’s Manual Introduction 1.
LV-667 User’s Manual Introduction 1.4 Embedded VIA C3 1.0GHz processor CRT/LCD Monitor Optional HDTV Optional DVI 1 x 184-pin Optional LVDS DDR266/333/400 Up to 1GB Optional AGP8x CN400 Ultra V-Link 1GB/s 6 x USB2.0 Ports 2 x SATA PCI VT6103 PHY VT8237 3 x IEEE1394a AC97 5.
LV-667 User’s Manual Hardware Setup Chapter 2 2.
LV-667 User’s Manual Hardware Setup 2.
LV-667 User’s Manual Hardware Setup 2.3 2.3.
LV-667 User’s Manual Hardware Setup 2.4 2.4.1< CPU> The board supports Embedded VIA C3/Eden processor, default ratio is C3 1.0GHz with CPU cooler fan, Eden ESP8000 (800MHz) with heatsink only. 2.4.2 The board supports one 184-pin DDR266/333/400 SDRAM and up to 1GB of capacity, only non-ECC, unbuffered memory is supported. DIMM 104-pin 80-pin Please check the pin number to match the socket side well before installing memory module.
LV-667 User’s Manual Hardware Setup 2.5 The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
LV-667 User’s Manual Hardware Setup 2.6 The board supports two enhanced IDE interface, dual channel for 4 ATAPI devices with ATA133. Based on embedded application, the board has one 40-pin IDE connector with jumper selectable for pin-20 +5V supported, and one 44-pin IDE connector. The jumper JDOM is two-pin type for pin-20 supplied with +5V to apply the DOM (Disk on Module).
LV-667 User’s Manual Hardware Setup 2.7 Based on VIA VT8237 Southbridge, the board supports two Serial ATA interfaces with RAID 0 and 1 array function. The following is the list of the specification of the Serial ATA. 1. Complies with Serial ATA Specification Revision 1.0 2. Dual Channel master mode PCI 3. On-chip two-channel Serial ATA (S-ATA) PHY for support of up to two S-ATA devices directly. 4.
LV-667 User’s Manual Hardware Setup 2.8 The board provides a slim type floppy port; please use the 26-pin ribbon cable in the package to connect the floppy device. FDD Floppy rear side 1. 20 4. Lift up this plastic bar 5. Slot the cable in (Blue paste for outside) 6. Press back the plastic bar Lift up the brown plastic bar 2. Slot the cable in (Blue paste for 3.
LV-667 User’s Manual Hardware Setup 2.9 The board provides two 10/100Mbps LAN interfaces with VIA VT6103 PHY and REALTEK 8100B PCI controller, and compliant with standard IEEE 802.3 Ethernet interface for 100BASE-TX. The jumper of JLAN can let you enable/disable LAN2 with REALTEK 8100B. The CN_WOL is the interface for your PCI LAN card to wake the system up.
LV-667 User’s Manual Hardware Setup 2.10 Based on VIA CN400, the board supports integrated S3 Graphics UniChrome Pro IGP graphics, with BIOS selectable 16/32/64MB shared with system memory for frame buffer. 2.10.
LV-667 User’s Manual Hardware Setup 2.10.2 The board provides optional DVI-D interface with VIA VT1632, compliant with DVI 1.0 standard, and supports dual display (clone or extended desktop) function with CRT. Connector: CN_DVI Connector type: 26-pin header connector (pitch = 2.
LV-667 User’s Manual Hardware Setup 2.10.3 The board provides an HDTV and SDTV interface with VIA VT1625, supports PAL and NTSC of TV system, and dual display (clone or extended desktop) function with CRT. Connector: CN_SDTV Connector type: 8-pin header SDTV connector (pitch = 2.54mm) Pin Number 1 3 5 7 Assignment GND C GND CVBS Pin Number 2 4 6 8 Assignment Y GND GND GND Connector: CN_HDTV Connector type: 10-pin header HDTV connector (pitch = 2.
LV-667 User’s Manual Hardware Setup To connect the TV set, please follow the diagram below to setup your system: YPrPb Component Cable (For HDTV) S-Video & Composite Cable (For SDTV) Onboard Display Interface 25
LV-667 User’s Manual Hardware Setup 2.11 The board provides the onboard AC97 5.1-channel audio interface with VIA VT1616, with three phone jacks on rear I/O panel for Line-out, Line-in, MIC(stereo)-in as 2-channel sound system, and Front, Rear, Center as 5.1-channel sound system. It also has one 10-pin header for additional audio output and 4-pin S/PDIF interface for optical/coaxial output.
LV-667 User’s Manual Connector: CN_AUDIO Type: 10-pin (2 x 5) header (pitch = 2.00mm) Pin Description Pin 1 Line – Left 2 3 Line – Right 4 5 MIC2 6 7 N/C 8 9 Line Out – Right 10 Hardware Setup Description Ground MIC1 Ground Line Out – Left Ground Connector: CDIN (LV-667E8 series do not have this connector) Type: 4-pin header (pitch = 2.54mm) Pin Description 1 CD – Left 2 Ground 3 Ground 4 CD – Right Connector: SPDIF Type: 4-pin header (pitch = 2.
LV-667 User’s Manual Hardware Setup 2.12 Based on VIA VT8237, the board provides 6 USB2.0 ports, and 3 IEEE1394a with VIA VT6306. The USB2.0 interface provides up to 480Mbps of transferring rate, the IEEE1394a provides up to 400Mbps of transferring rate. Interface IEEE1394a USB2.0 Controller VIA VT6306 VIA VT8237 Transfer Rate 100/200/400Mb/s Up to 480Mb/s Output Voltage 12V 500mA 1394_1 1394_2 USB1/2/3/4 8 1 CN_1394 10 1 CN_USB 28 USB2.
LV-667 User’s Manual Connector: CN_1394 Type: 8-pin header (pitch = 2.00mm) Pin Description 1 CPWR 3 TPB25 TPA27 GND Hardware Setup Pin 2 4 6 8 Description GND TPB2+ TPA2+ GND Connector: CN_USB Type: 10-pin (5 x 2) header for USB5/6 Ports Pin Description Pin 1 VCC 2 3 Data04 5 Data0+ 6 7 Ground 8 9 Ground 10 Description VCC Data1Data1+ Ground N/C PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you insert an USB1.1 device, the port will be changed to USB1.
LV-667 User’s Manual Hardware Setup 2.13 The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK. Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.
LV-667 User’s Manual Hardware Setup 2.14 The board provides four RS232 serial ports, with jumper selectable +5V/+12V output for COM3 and COM.
LV-667 User’s Manual Hardware Setup 2.15 2.15.1 Connector: ATXPWR Type: 20-pin ATX power connector PIN assignment 1 12V 2 5VSB 3 PWOK 4 GND 5 5V 6 GND 7 5V 8 GND 9 3.3V 10 3.3V 11 12 13 14 15 16 17 18 19 20 5V 5V -5V GND GND GND PSON GND -12 3.3V 2.15.
LV-667 User’s Manual Hardware Setup 2.16 The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.
LV-667 User’s Manual (This Page is Left For Blank) 34
LV-667 User’s Manual System Configuration Chapter 3 3.1 The board supports two Serial ATA ports onboard, and supports RAID 0, 1 and JBOD disk array, the RAID 0, 1 and JBOD are specified below: RAID 0 (Stripping): Two hard drives operating as one drive for optimized data R/W performance. It needs two unused drives to build this operation.
LV-667 User’s Manual System Configuration You also can edit disk array under OS, please install the VIA RAID Utility in the driver CD.
LV-667 User’s Manual System Configuration 3.2
LV-667 User’s Manual System Configuration 3.3 The board provides onboard analog VGA interface, and optional digital display interface with HDTV, LVDS and DVI, please install the VIA video driver before enjoy the vivid display. Based on the VIA CN400 with S3 UniChrome Pro graphic, the board provides dual display function for clone or extended desktop modes with secondary display device attached. After installing video driver, please launch the desktop display properties.
LV-667 User’s Manual System Configuration Please select S3Display for advanced device setting. Connected Devices Click check box to enable/disable device Specified display setup When you set dual display clone mode, you’ll see the same screen display on two devices. When you set the dual display for extended desktop mode, you can have the independent desktop on the second device.
LV-667 User’s Manual (This Page is Left for Blank) 40
LV-667 User’s Manual BIOS Setup Chapter 4 The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
LV-667 User’s Manual (This Page is Left for Blank) 42
LV-667 User’s Manual I/O Port Pin Assignment Appendix A A.
LV-667 User’s Manual Connector: IDE2 2 44 1 43 Type: 44-pin (22 x 2) box header Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 44 Description Reset D7 D6 D5 D4 D3 D2 D1 D0 Ground REQ IOW-/STOP IOR-/HDMARDY IORDY/DDMARDY DACKIRQ A1 A0 CS1 ASP1 Vcc Ground Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 Description Ground D8 D9 D10 D11 D12 D13 D14 D15 N/C Ground Ground Ground Ground Ground N/C SD A2 CS3 Ground Vcc Ground IDE Port
LV-667 User’s Manual I/O Port Pin Assignment A.2 Connector: FDD Type: 26-pin connector Pin Description 1 VCC 3 VCC 5 VCC 7 DRV1 9 MTR1 11 RPM 13 N/C 15 Ground 17 Ground 19 N/C 21 N/C 23 Ground 25 Ground Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 Description INDEX DRV0 DSKCHG N/C MTR0 DIR STEP WRITE DATA WRITE GATE TRACK 0 WRPTR RDATASEL A.
LV-667 User’s Manual 6 A.4 < VGA Port > Connector: VGA Type: 15-pin D-sub female connector on bracket Pin Description Pin Description 1 RED 6 Ground 2 GREEN 7 Ground 3 BLUE 8 Ground 4 N/C 9 LVGA5V 5 Ground 10 Ground A.5 1 1 2 3 4 5 11 12 13 14 15 10 Pin 11 12 13 14 15 Description N/C 5VCDA HSYNC VSYNC 5VCLK 7 Connector: CN_SATA1/2 Type: 7-pin wafer connector 1 2 3 4 5 6 7 GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND A.
LV-667 User’s Manual I/O Port Pin Assignment A.8 1 Connector: RJ45_1/2 Type: RJ45 connector with LED on bracket Pin Description 1 TX+ 2 TX- 3 RX+ 4 N/C 8 5 N/C 6 RX- 7 N/C 8 N/C A.
LV-667 User’s Manual (This Page is Left for Blank) 48
LV-667 User’s Manual I/O Port Pin Assignment Appendix B B.1 BIOS Auto Flash Tool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below: http://www.award.com http://www.commell.com.tw/support/support.htm TU UT TU UT File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS. B.2 Flash Method 1. Please make a bootable floppy disk. 2.
LV-667 User’s Manual (This Page is Left for Blank) 50
LV-667 User’s Manual System Resources Appendix C C.
LV-667 User’s Manual Address Range Devices System Resources x03F6 - x03F6 Primary IDE controller (dual fifo) x03F7 - x03F7 Standard Floppy Disk Controller x03F8 - x03FF Communications Port (COM1) x0400 - x047F Motherboard resources x04D0 - x04D1 Motherboard resources x0500 - x050F Motherboard resources x0CF8 - x0CFF PCI bus xD000 - xD0FF Realtek RTL8139/810x Family Fast Ethernet NIC xD400 - xD4FF VIA SATA RAID Controller xD800 - xD8FF Vinyl AC'97 Codec Combo Driver (WDM) xDC00 - xDCFF
LV-667 User’s Manual System Resources C.
LV-667 User’s Manual System Resources C.3 C.3.
LV-667 User’s Manual IRQ Number Devices 12 PS/2 Compatible Mouse Port 13 Numeric data processor 14 Primary IDE controller (dual fifo) 14 VIA Bus Master PCI IDE Controller 15 Secondary IDE controller (dual fifo) 15 VIA Bus Master PCI IDE Controller System Resources C.3.
LV-667 User’s Manual (This Page is Left for Blank) 56
LV-667 User’s Manual Power Consumption Test Appendix D Hardware CPU Memory HDD CDROM Power Supply Embedded VIA C3 1.0GHz HYNIX DDR400 1GB Seagate ST340014A SONY DDU1621 DVD-ROM AOPEN FSP300-60ATV (not counted) (not counted) Software OS Application Windows XP SP1 English Version 3DMARK 2001 Test Result 3.3V 5V 12V 0.3A 3.5A 0.2A 0.99W 17.5W 2.4W Embedded VIA C3 1.
LV-667 User’s Manual Contact Information Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your pr Taiwan Commate Computer Inc. Address 8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih Taipei Hsien, Taiwan TEL +886-2-26963909 FAX +886-2-26963911 Website http://www.commell.com.tw TU UT info@commell.com.tw (General Information) E-Mail TU UT tech@commell.com.
