--------------------------------------------------------------------------------------------- DVD±RW Dual Drive DRW8800 AAN/AAG User's Manual -1-
--------------------------------------------------------------------------------------------Laser Safety Information This drive employs a laser. Do not remove the cover or attempt to service this device when connected due to the possibility of eye damage. CAUTION Use of control of adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This label is located on top enclosure of this drive.
--------------------------------------------------------------------------------------------NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
--------------------------------------------------------------------------------------------- Table of Contents Cautions Cleaning............................................................................................................................................. 5 Handling the Disc ............................................................................................................................... 5 Part Names and Functions Front View......................................................
--------------------------------------------------------------------------------------------- Cautions Cleaning To clean the DVD R/RW drive, wipe it with a soft, damp cloth, using mild detergent if necessary. Please avoid using solvents such as benzine or paint thinner. This can cause color changes or deformation of DVD R/RW drive. Handling the Disc • Do not touch the data side of the disc (the side of the disc with no label or printing).
--------------------------------------------------------------------------------------------- Part Names and Functions Front View 1 2 3 4 1 BUSY Indicator This indicator lights green while data is being read and written. 2 Tray Panel This panel prevents dust from entering the DVD R/RW drive. The disc tray will be ejected when the Load/Eject button is pushed. 3 Emergency Eject Hole Use to remove the disc from the DVD R/RW drive if the electrical eject is disabled by software or if power failure occurs.
--------------------------------------------------------------------------------------------- Rear View 6 7 8 5 5 Jumper Blocks These blocks of jumper locations set the configuration for the DVD R/RW drive. (See page 8, “Jumper Setting” for details.) 6 DIGITAL OUT Connector This connector is used to connect CD Digital Audio to an audio board. 7 Line Out Connector This connector is used to connect CD-Audio to an audio board.
--------------------------------------------------------------------------------------------- Preparation Jumper Setting A jumper consists of a pair of pins and a connector which fits over the pins. When the connector is in place it establishes an electronic link between the pins, which enables the function being controlled by the jumper. If the connector is removed, the electronic link is broken and the function is disabled.
--------------------------------------------------------------------------------------------- Installing the DVD R/RW drive in a host PC Note Refer to the guidebook included with your personal computer for instructions on installing the DVD R/RW drive. This chapter gives one example of installation. And, when disconnecting the DVD R/RW drive from computer equipment, please wait to remove a couple of minutes until it gets cold. The enclosure may have some points over 60 C degree. 1.
--------------------------------------------------------------------------------------------- 5. Locate a spare power cable in your computer. 6. Connect that power cable to the power connector on the back of the DVD R/RW drive.
--------------------------------------------------------------------------------------------- 7. Connect the I/O BUS connector on the DVD R/RW drive and the IDE connector. Connect the colored stripe side of the cable to the side marked with the arrow . 8. Slide the disc drive and DVD R/RW drive into the computer. 9. Replace the mounting clips, keeper bracket, and computer cover.
--------------------------------------------------------------------------------------------- Inserting/Removing a Disc Using the DVD R/RW Drive Installed Vertically When using the DVD R/RW drive, in the vertical position, load and unload discs as shown on the diagram below. DVD R/RW drive installed vertically DVD R/RW drive installed vertically (left side) (right side) Caution Only 12cm discs can be used when the DVD R/RW drive is installed vertically.
--------------------------------------------------------------------------------------------Inserting a Disc 1. Press the Load/Eject button. The disc tray will be ejected. 2. Place the disc in the center of the tray with the label side facing up. 3. Press the Load/Eject button. The disc tray will be retracted. Removing a Disc 1. Press the Load/Eject button. The disc tray will be ejected. 2. Remove the disc. 3. Press the Load/Eject button. The disc tray will be retracted.
--------------------------------------------------------------------------------------------- Specifications DVD Section User Data Capacity ........................................................ 4.7 GBytes (Single layer, 12cm), 8.54 GBytes (Dual layer, 12cm) 1.46 GBytes (Single layer, 8cm), 2.66 GBytes (Dual layer, 8cm) User Data Blocks ............................................................ 2048 Bytes/block Data Transfer Rate ......................................................... 16.
--------------------------------------------------------------------------------------------CD Section User Data Capacity ........................................................ 656 Mbytes/disc (Mode 1) (1MBytes = 1024 x 1024) ............................................... 748 Mbytes/disc (Mode 2) User Data Blocks ............................................................ 2048 Bytes, Mode 1 and Mode 2 Form 1 2336 Bytes, Mode 2 2328 Bytes, Mode 2 Form 2 Access Time .......................................
--------------------------------------------------------------------------------------------IDE Interface Section Burst Transfer Rate ......................................................... PIO mode 4 DMA Single Word mode 2 DMA Multi Word mode 2 Ultra DMA 33 mode 2 Memory Buffer ............................................................... 2 MBytes Audio Section FREQUENCY RESPONS .............................................. 20 Hz - 20 kHz +3.0 dB, -3.0 dB S/N RATIO .................................
